Question about 1982 Porsche 911

1 Answer

Indicators The indicators do not work or the hazards the flasherunit was working but only rght hand rear indiator flashed now I have nothing also front indicators were not wired correctly I hve no idea where to wire them. Can you help Alan I might add the car has been in or a e spray and is a porsche 911 sc 3ltr

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 132 Answers

Mark from exoticars will help 97370311

Posted on Nov 09, 2008


1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My rear turn signals are not working. front turn signals work rear parking lights work brake lights work


In the diagram for rear lamp, the top wires are voltage, the bottom black wire is ground. The brown wire on either side should be tail lamps, goes hot when you turn on the headlamp switch. The other top wire on either should be for turn signal. With everything turned on, is there voltage on that wire?
Because the front works and the rear don't, possible wiring circuit problem? The voltage for turn signals comes from bcm. The bcm knows when you turn on turn signal switch, either side, then the bcm sends voltage to turn signal lamp at the rear and front.

rear-turn-signals-not-working-front-nrw1b5lbo1usuvcsnuvurzx3-3-0.jpg

Oct 17, 2016 | 2009 Chevrolet Chevrolet HHR LS

1 Answer

Left rear turn signal, rear hazard lights not working


You will be needing a good electric meter.
With the key on and the turn signal activated, test the leads inside the light socket and see if electricity is getting to the bulb.
When you mentioned it flashes really fast, that says one of the bulbs is not working.
Although it could be burned out, it could also not be making contact, or the ground wire could be bad.
Since the early '80's, cars and trucks have had separate ground wires to each and every bulb and electrical component, and a bad ground will cause this problem also.
Remember, a bulb can look good and still be no good.
God bless your efforts.

Apr 19, 2016 | 2007 Ford Freestyle Limited

3 Answers

Turn signals not working


all else on car works perfectly (other shoe drops??????)
waring 1: no scan tool, you will fail (99%)
is battery fully charged to 12.6vdc rested or at 10v?
all 4 corners dead?
not working means dead?, flashes too fast/slow or dim? or they stick on? (5 modes to fail not counting L/R and haz)
do the hazards work? (prime evidence and not stated)
most cars before 2007 have fuse marked TURN.
but not this car... its not at all like older cars....
did you scan it first after the fuse tests? any PCM scan tool.?
2009 WK jeep
the FSM chapter 8L shows the huge list of errors the lamps can fail. DTC errors.
in fact 8 blinker codes, ! DTC errors,

there is no fuse, just for turns, (trailer lamps fuse 19)

read this excerpt from the FSM book.

The turn signal system operates on battery current received on a fused ignition switch output (run) circuit so that the
turn signals will only operate with the ignition switch in the On position. The hazard warning system operates on
non-switched battery current received on a fused B(+) circuit so that the hazard warning remains operational regardless
of the ignition switch position. When the turn signal system is activated, the circuitry of the left multi-function
switch and the FCM will cause the selected (right or left) turn signal indicator, front park/turn signal lamp, front side
marker lamp and rear tail/stop/turn signal lamp to flash on and off. When the hazard warning system is activated,
the circuitry of the hazard warning switch and the FCM will cause both the right side and the left side turn signal
indicators, front park/turn signal lamps, front side marker lamps and rear tail/stop/turn signal lamps to flash on and
off. The Front Control Module (FCM) can also activate the hazard warning system lamps.
end quote)

the module front control MFC, runs this
and it uses fuse 18 , if 18 blows the module goes off line and vast things fail and huge numbers OF DTCs store.
and fuse 27 MFC
MFC needs these fuses good.
keep in mind nobody has MFC internal schematics...so........



this module drives left and right side front and rear.
electronic drivers, not fuses.
the MFC is here.
the fuses are 12,13,18, 20,27 that power MFC.


25812039-lb3yimx2pwhstnjl4tgwffiq-2-0.jpg ground this end.

Aug 07, 2015 | 2009 Jeep Grand Cherokee

1 Answer

The indicator lights are all stuck on. AU Ford station wagon. Removed relay, and all fuses, but still on. Disconnected battery and they turned off. Reconnected battery and they all came back on with no...


The AU ford has two indicator relays , turning lights and hazard lights ,both use the indicator lights ,the hazards flash both front and rear lights , the turning indicator flashes one front and one rear light. I think the fault may be in the hazard circuit.

Feb 25, 2015 | Ford Cars & Trucks

1 Answer

I have a renault megane 2.0 convertible, my lefthand indicator stays on when stalk is in lefthand position and also in mid position, it only cancels in righthand position which means I have no righthand...


Hi, my lefthand indicator light is not functioning propely on my Renault megane scenic 1.6. 2001 model. there is that flicker sound when I turn it on and it ticks very fast and nothing flashes on the dash and nothing on the external lights as well. It also does the same thing on the hazards but the right hand side works perfect. please help. EDDIE

Jul 10, 2013 | Cars & Trucks

1 Answer

Front indicators dont flash


Quick flashing is usually a burnt out bulb.

Oct 27, 2012 | Nissan Cars & Trucks

1 Answer

1999 oldsmobile aurora side marker light flash on and off when the car is turned off


Power is appliedat all times through the 20A HZRD/ STOP LPS fuse in the right rear junction block. The ORG wire connects to the hazard flasher and the BRN output wire connects to the A5 terminal of the TURN/HAZARD switch assembly. When the HAZARD switch is engaged, power is applied to the front and rear turn signals and the left and right turn indicators in the instrument cluster, causing them to flash. Obviously an open fuse, a defective flasher, a defective HAZARD switch, or a defective TURN/HAZARD switch assembly will prevent the lamps from flashing. If the turn signals operate normally, they are not the problem.

Sep 05, 2012 | 1999 Oldsmobile Aurora

1 Answer

The blinker indicators inside blink super fast. the front ones work fine, nothing with the rear ones. same thing wiht the hazards-the fronts flash but not the rear.


They blink fast because there is not enough load on the system a bulb or two are out replace the two rear bulbs if they are not flashing

Sep 18, 2011 | 2005 Chrysler Pacifica

1 Answer

I havea 1995 Ford Fiesta and the indictor lamps(front and rear) only work on the right hand side, if you try to indicator to turn left you just get a ticking from behind the instrument panel and neither...


Try the hazard lights to check if all four lights flash, if not then check the bulbs. If the bulbs are ok check the contacts and the connections. if all all these are ok the problem could be the indicator switch. The flasher unit is fitted in the circuit before the indicator switch, that is why it operated although the lights might not.

Jan 17, 2011 | Ford Fiesta Cars & Trucks

1 Answer

Rear turn signal and hazard light don't flash (left side only)


The rear left turn signal bulb must be replaced immediatly before it melts the light socket, if it has'nt yet. Also please verify that the correct light bulb is being installed. because even though many bulbs look the same they are not identical. Installing the wrong bulb can be the begining of many, many problems in the particular circuit

Mar 26, 2010 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

64034 Answers

Randy Ohler

Level 3 Expert

14584 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...