Question about 1994 Hyundai Excel

1 Answer

Hyundia lantra 1.8 crank sensor

I need help in locating were the crank angle sensor is and how to fit a new one can you help me?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 25 Answers

What model engine is in this car???if it has a distributor then thats where it is, if its multi coil then it may be behind the cambelt covers at the bottom

Posted on Aug 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I find the crank sensor on a 2009 Nissan Titan v8 truck?


i think it's the starter. On most nissans, the starter and the crank position sensor are close to each other. Some nissans have 4 position sensors, between crank sensor, crank angle sensor, cam position sensor, and sensor sensing sensor, oh and cam angle sensor. Oh wait, maybe it's a bad ground. Nope, gotta be the staerter.
25440212-xipalmoknr3fbjmp51kycajc-3-0.jpg

25440212-xipalmoknr3fbjmp51kycajc-3-1.jpg

Feb 17, 2015 | Nissan Cars & Trucks

1 Answer

How to change crank angle sensor on 2000 model vectra


Just disconnect the plug and wires undo the retainer bolt s then remove and fit the new one

Sep 12, 2014 | Opel Vectra Cars & Trucks

2 Answers

How to replace a crank case sensor on 1996 nissan pathfinder?


Crank case sensor? Sorry, I don't think I've ever heard of one. Crank position sensor? (Prob top of the bell housing directly behind the cylinder head, 10 mm headed bolt holds the shield and the sensor in place, but is only used when trouble shooting misfires.)

Jun 30, 2014 | 1996 Nissan Pickup

3 Answers

I have a 1985 fiero se v6 that was running fine but cutting off after warm up


Do you know what you are loosing when the engine stops running ?

Jan 16, 2014 | 1985 Pontiac Fiero

1 Answer

Location of cam and crank angle sensor in 96 N15


The cam and crank position sensor can be found in the front of the crank on the engine block below or next to the water pump in many applications.
It can also be located on the main crank pully or the flywheel.

Feb 09, 2012 | Nissan Pulsar Cars & Trucks

1 Answer

How do i replace the crank position sensor on a 2000 jeep grand cherokee


If you have the type of crank angle sensor shown in the image, then it will be located on the bell-housing towards the top of the bell-housing and usually on the drivers side. Dis-connect the faulty crank angle sensor and then un-bolt the two bolts that secure the crank angle sensor to the bell-housing and then remove the sensor. The best access to the crank angle sensor is from under the vehicle.


47ada7e.jpg

Jun 21, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Crank angle sensor location


The crank sensor is always located next to the crankshaft pulley. it will be inserted into the block with the top part of the housing half way out. you cant miss the wires leading into the tip of the housing next to the crank shaft pulley.

May 23, 2009 | Nissan Cars & Trucks

1 Answer

Need location of crank angle sensor on 1997 pontiac sunfire 2.2 liter


Hello oldiro: My name is Roger and I can help. From under the vehicle look up between the transmission and the side of the block. Mid motor above the pan rail there is a bolted in sensor. This should be the crank sensor.It will have two wires plugged in to it. Please rate this answer as this lets us know you received the information you asked for. Should you need further help please just ask. Thank You for using FixYa. Roger

May 06, 2009 | Pontiac Sunfire Cars & Trucks

1 Answer

Wont start


what is the code number?? you may need a new crank angle sensor. common problem. car will not start without crank angle sensor signal/input. find out what the code is and post. if code number you get is P0335, than install new crank angle sensor.

Aug 01, 2008 | 2002 Nissan Altima

Not finding what you are looking for?
1994 Hyundai Excel Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...