Question about 2002 Volvo S40

Open Question

Arbol de levas

El mecanico desajusto el arbol de levas mobible y no se ponerlo a tiempo

Posted by on

6 Suggested Answers

Benimur
  • 6966 Answers

SOURCE: benimur

Hi,

To my understanding, on an Audi A4, error code P1392 indicates camshaft sensor circuit. This could be a faulty sensor the camshafts are not correctly timed. 90s Audis are not very common in my country but from what I can gather:

The mark for the crankshaft gear is on the cover you have to remove in order to get at the timing belt. The sprocket you may be having trouble with is the intermediate shaft (in front of the water pump) and I don't believe that one matters at all since it doesn't drive any of the cams. The intake cams are driven by a chain off of the exhaust cam shaft so only the exhaust cam is driven directly by the timing belt.

Additionally, you may benefit from the Audi A4 Service Manual and/or Audi A4 Cabriolet Workshop Manual.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Posted on Aug 28, 2008

  • 1 Answer

SOURCE: hola , mi carro tiene

pudiste resolverlo? yo tengo el mismo problema

Posted on Jan 08, 2011

  • 1 Answer

SOURCE: como poner cadena de tiempo a motor de ford ranger 2003

Como loner el filtro de gasolina En 2003ford focus

Posted on Feb 26, 2011

sammyc47
  • 95 Answers

SOURCE: A PESAR QUE SE HA

Verifica el termostato,2- likeos de coolant,3- funcionamiento del radiador, bomba de agua( si no ves movimiento del agua del radiador cuando el vehiculo esta encendido, entonces la bomba del agua esta defectuosa,Verifica el tiempo,(timing). Espero que esta info. te sea de ayuda...sammyc47....

Posted on Mar 02, 2011

ZJLimited
  • 17970 Answers

SOURCE: como colocar el tiempo de

Saludos, sugiero usar algun traductor para resolver estos detalles, obtenidos de un Boletin Tecnico de Servicio (TSB = Technical Service Bulletin)

A couple things you may want to be aware of, before getting too deep into this one:
(1) There is a factory recall under which the timing belt and sometimes tensioner components are replaced on this vehicle. you may want to check with the dealer to see if yours is still under an open recall for this; if so, they will replace the timing belt and any necessary related components for free. The recall is #01L002000 (description follows):

This is not a safety defect in accordance with the Safety Act. However, it is deemed a safety improvement campaign by the agency.

Vehicle Description: 1998-2000 Rodeo (UE) and Amigo (UA) models equipped with 2.2L 4-cylinder engines. The timing belt could break before the recommended scheduled maintenance.

This condition could cause the engine to crank but will not start or the engine could stall while driving and will not restart.

Dealer will inspect the vehicle to determine the condition of the timing belt and tensioner. The dealer will replace the timing belt. Depending on the condition or model of the timing belt tensioner, the tensioner may also be replaced. Isuzu has decided to conduct a Service Campaign to replace the timing belt. Owners can contact Isuzu at 1-800-643-4070, ext. 426, concerning this program

Second, there is a revised procedure involved in indexing the camshafts during timing belt replacement. This is most likely not detailed in your Haynes manual, but is outlined in an Isuzu service bulletin. Here is the procedure as described in the TSB:

BULLETIN NUMBER: IB00-S005
GROUP: INFORMATION
ISSUE DATE: FEBRUARY 2000

3.5L V6 DOHC (6VE1) / 3.2L V6 DOHC (6VD1) ENGINES: TIMING BELT INSTALLATION

AFFECTED VEHICLES: The following models equipped with "Direct Attack" DOHC 3.2L / 3.5L V6 engine:
^ 1998-2000 Rodeo (UE)/ Amigo(UA)
^ 1998-2000 Trooper (UX)
^ 1999-2000 VehiCROSS (VX)

SERVICE INFORMATION
This information bulletin outlines the proper steps to index the camshafts with the crankshaft. In the event that camshaft timing has been disrupted, due to timing belt breakage or camshafts/crankshaft being rotated without a timing belt, this is important prior to timing belt installation. Due to the gear-ratio used by each camshaft pulley to drive the camshafts, engine timing cannot be indexed conventionally.

SERVICE PROCEDURE

IMPORTANT: In the following procedures, the references to 9 or 12 O'clock positions are based on deck plane of the cylinder deck-to-cylinder head mating surface (as viewed from the front of the engine), and NOT RELATIVE TO THE SHOP FLOOR.

1. In the event that camshaft timing has been disrupted, due to timing belt breakage or camshafts/crankshaft being rotated without a timing belt, please proceed to Step 2. Otherwise, continue with Step 22 for timing belt servicing procedures. (after removal of front timing belt covers as outlined in the appropriate Workshop Manual).

2. After cylinder head servicing as outlined in the appropriate Workshop manual, proceed to the following steps.
3. Lubricate and install the idler gear.
4. Inspect the idler gear retaining cover for wear.

NOTE: There is a 0.039 lubrication hole drilled into the idler gear retaining cover. Always inspect this hole for obstruction.

IMPORTANT: Do not use a liquid gasket material on the idler retaining cover. Always replace the retaining cover with a new 0-ring. Be sure to lubricate the 0-ring prior to installation.

5. Install the idler cover and torque (10 Nm, 8 lb ft) the 6 mm bolts
6. Align the right bank idler shaft alignment marks.

IMPORTANT: Align the idler gear dowel pin to its corresponding mark on the idler gear retaining cover before installing the camshafts

7. Use special J-tool to pre-load the sub gear assembly.

NOTE: Use special J-tool J-42686. Once the sub-gear has been pre-loaded, install the 5 mm bolt supplied with the tool and insert it into the camshaft from the back of the camshaft gear assembly. Tighten the bolt to lock the sub-gear in place.

IMPORTANT: When the sub gear is pre loaded, the teeth on the sub gear should be aligned with the teeth on the camshaft gear.

8. Install the odd bank camshaft(s) into the cylinder head.

NOTE: Before installing the camshafts, pre-lube the cam lobes using a suitable molybdenum assembly grease

IMPORTANT: The single dot on the camshaft gears must be aligned with their corresponding marks on the idler gear. Also, do not remove the 5mm bolt holding the sub-gear, until the camshaft journal caps are installed and the bolts are torqued.

9. Install the camshaft journal retaining caps and torque (10 Nm, 8 lb ft).

IMPORTANT: The camshaft journal caps are numbered to prevent mis-matching. However, pay close attention when installing the caps on the odd bank cylinders. because the cap arrows will face the front of the cylinder head.

10. Place a small amount of RTV sealer on the head surface where the cap contacts the head surface.
11. Repeat Steps 3-5 for even bank cylinders.
12. Align the left bank idler shaft marks (Refer to figure 3).
13. Pre-load the sub-gear assemblies (Refer to figure 4).
14. Install the even bank camshafts and pre-lube the cam lobes using a suitable molybdenum assembly grease (Refer to figure 5).
15. Install the camshaft journal retaining caps and torque (10 Nm, 8 lb ft).

IMPORTANT: The camshaft journal caps are numbered to prevent mis-match mg. However, pay close attention when installing the caps on the even bank cylinders, because the cap arrows will face the rear of the cylinder head.


continue...

Posted on Aug 17, 2011

  • 2 Answers

SOURCE: poner a tiempo cadenas de distribucion ford motor 4.0 mod 2002

necesito poner a tiempo las cadenas y los engranes del tiempo del motor de un altima nissan modelo 1997 2.4

Posted on Aug 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tengo el codigo 343 kia sephia 2000 a veces se desplaza algo lento!


codigo P0343 es el sensor de posicion del arbol de levas. Que no esta legendo cambiar la derecha el sensor que se encuentra por encima de la manguera de aqua en la cabeza.

Feb 17, 2015 | 2000 Kia Sephia

1 Answer

Mi camioneta isuzu se apago corriendo y ya no prende la computadora mi marca un codigo po342 que puede ser el sensor de posicion de el arbol d levas se lo puse nuevo y siguio igual. que puede ser otra


please post in english his is USA forum. and is english only.
here ill use google translate for you.
My truck Isuzu no longer running and turn off the computer turns my marks a po342 code that may be the position sensor of the tree cam d put it back and continued the same. which can be another.

Ok , P0342 is clear in the book, (but you never said engine type in car>? so......)
here are the possibles.
1: CMP sensor dead or bad.
2: cam timing way off. (is compression TEST over 150 PSI on all cylinders? (no engine stated, so.... cant tell you why see?
3: bad wiring to the CMP.
4: or CMP timed wrong.

CMP is the name of the CAM SENSOR. BTW.
no car stated.
no year stated.
no engine stated
no country, yes, cars do vary greatly by , COUNTRY.
mostly hopeless so for...


use google translate to translate ENglish back to Spanish.

to do so type, Translate in the google box and magic happens.

Nov 30, 2014 | Isuzu Cars & Trucks

1 Answer

Diagrama cadenas del tiempo de suzuki aerio 2.3lts 2005


nececito el diagrama para poner a tiempo la cadena del tiempo los puntos donde deven de hir creo que se movio el tiempo de mi carro y el mecanico me la pide

Jun 18, 2012 | 2002 Suzuki Aerio

2 Answers

Marcas para poder sincronisar tiempo toyota corolla 94


en la polea del arbol de levas veras un hueco pequeño en una de las paletas, este debe apuntar a las 12 como el reloj y veras una marca en la primera abrazadera del arbol de levas , en cuanto a la polea del cigueñal , veras una marca en la parte lisa , debe estar alineada con un punto que sobresale de la tapa frontal del motor , creo que como a las 11 del reloj,eso es todo, cualquier cosa me escribes a mecanica03@hotmail.com

Sep 06, 2010 | Toyota Corolla Cars & Trucks

1 Answer

La posicion dela banda del tiempo de caravan 3


como poner la banda de tiempo a una dodge grand caravan 1994,motor 3.0

Jan 17, 2010 | 1989 Dodge Caravan Cargo

1 Answer

Haw can change the band of distrubution?


ok sure you speak spanish because we says to timing belt = banda de distribucion. I will write in spanish :)

Lo que tienes que hacer con la banda de distribucion de tu Jetta 1994 es quitar las bandas externas de tu auto, luego de esto lo que tienes que hacer es quitar la polea del cigueñal para lo cual iras a requerir un extractor de poleas, ya que extraigas la polea del cigueñal y quites la tolva que guarda a la banda de distribucion y a los de los arboles de levas entonces gira con el maneral el cigueñal hasta las marcas del tiempo q deben estar marcadas en el motor o monoblock y/o en las tolvas, verifica estas marcas poniendo tu auto en punto muerto superior que es que el piston 1 quede hasta arriba lo puedes ver con un desarmador claro para esto tienes que quitar la bujia de tu auto del piston 1.

bueno ya que tengas esto prosigues a marcar la banda con alguna tinta o corrector tambien marca las poleas de los arboles o arbol y la del cigueñal, quita el tensor y va a salir la banda.

cuenta los dientes entre marca y marca y luego de eso marcalos en la nueva banda de distribucion. con el tensor de banda contraido pones la banda verifica que esten en sus marcas y luego vuelve a tensar la banda con su tensor.

si no sabes cuanto tensar solo verificar que la banda no debe doblar mas de 60 grados maximo 90 grados si gira mas entones esta floja.

ya puesta la banda verifica y dale 2 vueltas al cigueñal con el maneral y dado, si quedan en el mismo lugar las marcas luego de 2 vueltas completas de la polea entonces esta a tiempo si se atora se pone demaciado duro entonces las valvulas estan pegando.

vuelve a poner todo lo que desarmaste y listo!

Oct 16, 2009 | 1994 Volkswagen Jetta

2 Answers

El motor esta trabado


si se puede hacer pero de entrada es necesario desmontar el motor completo para desarmarlo xq no tiene espacio para hacwerlo montado y pues de cualquier modo podria salir algo caro y con algo de tiempo

Jul 18, 2009 | 2000 Lincoln LS

2 Answers

Como poner cadena de tiempo a motor de ford ranger 2003


Como loner el filtro de gasolina En 2003ford focus

Apr 30, 2009 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
2002 Volvo S40 Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Mark Jones

Level 2 Expert

76 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...