Question about 2000 Jaguar S-Type

1 Answer

S type can you tell me how to remove left side rear door glass

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 547 Answers

Remove door panel adjust window so you can see the mounts the window is attched to remove screw's/ bolt's lower window lift up at angle and pull out slowly don't hit glass on edges will break .

Posted on Feb 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing quarter glass on left side on 2005 pontiac gto


Remove the door opening weather-strip. Refer to Door Opening Weatherstrip Replacement in Doors.
Remove side sill trim plate. Refer to Door Sill Plate Replacement in Interior Trim.
Remove the lower quarter panel trim. Refer to Rear Quarter Trim Panel Replacement in Interior Trim.
Remove the center pillar upper trim panel. Refer to Center Pillar Upper Trim Panel Replacement in Interior Trim.
Remove the quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.
Remove the center pillar outer applique. Refer to Center Pillar Applique Replacement in Exterior Trim.
Remove the roof drip molding. Refer to Body Side Roof Drip Molding Replacement in Exterior Trim.

Important: It is necessary to use new nuts when reinstalling the quarter window.
Remove the nine quarter window nuts (1), securing the quarter window assembly (2) to the body opening.
Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
Important: When removing the quarter window from the body opening make sure that the attaching pins are clear of the outer body.
Remove the quarter window (2) from the body opening.

Remove the rear seat cushion. Refer to Rear Seat Cushion Replacement in Seats.
Remove the rear seat back. Refer to Rear Seat Back Replacement in Seats.
Remove the door sill plate. Refer to Door Sill Plate Replacement .

Remove the 3 quarter trim panel retaining screws (1).
Starting at the lower edge of the trim panel and moving alternately clockwise and counterclockwise, pull outward on the trim panel to disengage the eight rear quarter trim panel attaching clips (2).
Remove the quarter trim panel from the vehicle.
Remove the 4 radio speaker grille speed clips (1), securing the speaker grille.
Remove the speaker grille (2).
Remove the rear quarter trim panel insulator (1), from the back of the quarter trim assembly (2).
Remove 7 rear quarter trim panel armrest retaining clips (1).
Remove 7 rear quarter trim panel armrest retaining nuts (2).
Gently pry the quarter trim panel armrest insert assembly (3), away from the rear quarter trim panel and remove.

You mite look for a video on youtube !

Dec 23, 2016 | Pontiac Cars & Trucks

1 Answer

The left rear door window fell off the track. How do I remove the door panel to access it.


This is the complete procedure you stop when you see the problem.



1. REMOVE REAR DOOR INSIDE HANDLE BEZEL


(a) Remove the screw.


(b) Using a screwdriver with its tip taped, disengage the 2 claws A.


(c) Pull out the the rear door inside handle bezel in the direction indicated by the arrow, disengage the claw B, and remove the rear door inside handle bezel.


2. REMOVE DOOR PULL HANDLE


(a) Using a screwdriver wrapped with the protective tape, disengage the 2 clips and remove the door pull handle.


3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


(a) Remove the screw.


(b) Disengage the 7 clips.


(c) Disconnect the connector and pull up on the rear door trim board sub-assembly to remove it.


4. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


(a) Remove the bolt.


(b) Disengage the 2 claws and separate the rear door inside handle sub-assembly.


(c) Disconnect the 2 cables and remove the rear door inside handle sub-assembly.


5. REMOVE REAR SPEAKER


6. REMOVE REAR DOOR SERVICE HOLE COVER


(a) Disconnect each connector and remove the rear door service hole cover.


HINT:


Remove the remaining tape on the door side.


7. REMOVE REAR DOOR GLASS RUN


(a) Connect the window regulator switch assembly.


(b) Fully lower the door glass.


(c) Remove the rear door glass run.


8. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


(a) Remove the 2 bolts, the screw and rear door window division bar sub-assembly.


9. REMOVE REAR DOOR QUARTER WINDOW GLASS


(a) Pull out the direction indicated by the arrow, remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit.


10. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


(a) Remove the rear door glass sub-assembly as shown in the illustration.


(b) Disconnect the window regulator switch assembly.


12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


(a) Disconnect the connector.


(b) Loosen the temporary bolt.


NOTICE:


If the temporary bolt is removed, the rear door window regulator may fall and become deformed.


(c) Remove the 3 bolts and the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.


(d) Remove the temporary bolt from the regulator.


13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR


(a) Using a "torx" driver (T25), remove the 3 screws and power window regulator motor assembly rear.


14. REMOVE REAR DOOR LOCK ASSEMBLY


(a) Disconnect the connector.


(b) Remove the bolt.


(c) Using a "torx" socket wrench (T30), remove the 3 screws.


(d) Slide the rear door lock assembly downward, pull out the link from the outside handle frame, and remove the rear door lock assembly and cables as a unit.


(e) Remove the door wire harness packing.


(a) Using a "torx" socket wrench (T30), loosen the screw.


(b) Disengage the 2 claws and remove the rear door outside handle cover.


(a) Disengage the 2 claws and remove the rear door outside handle pad rear.

Jan 03, 2011 | 2006 Toyota Highlander

2 Answers

Rear door glass fell down, will not wind back up.


do not force anything ,remove the door panel and have a look then post if you need more help ,but it sounds like the either the clamp or the support is loose or corroded away

May 30, 2010 | 2000 Jaguar S-Type

1 Answer

How do i replace left door mirior


remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation
  1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
  1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
  1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
  1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
  1. To install reverse Removal procedure.
------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove front door trim panel (23942). Refer to Section 01-05 .
Trim Panels, Door Front—Town Car
Removal
  1. Snap out two door pull strap retaining screw covers. Remove screws.
  1. Remove three screws on front and rear side and center of front door trim panel (23942).
  1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

    Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
  1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

    Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
  1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
  1. Remove the door trim panel.
  1. Disconnect two electrical connectors.
  1. Remove nut from outside rear view mirror mounting base.
  1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
  1. Remove screw from outside rear view mirror base.
  1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
  1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-

Nov 05, 2009 | 1996 Lincoln Town Car

1 Answer

How to remove rear window in 1992 Jetta


there is difference but you did'nt mentioned the rear window but which one sir the rear main windshield glass or the rear door left or right door glass . 1. the rear windshield glass comes with a fixing silicon compond or silicate material which hold the glass firmly fixed attached to the body untill it break up then in this you need to consult to your nearest authorised dealer or authorised service centre for changing or removal of this sort's of glass  2. the rear door glass weather it is left side or right side the auto mechanic can do the job for you it's simple you your self can do for youself but some precaution measure has to be taken or either the glass will get break up so better consult the authorised service station 1st so for more soultion do write to us & till then drive safe drive carefully...!

May 24, 2009 | 1992 Volkswagen Jetta

1 Answer

Rear Window- Drivers side- won't work


Removal and Installation
  1. Remove the rear door trim panel. For additional information, refer to Section 501-05 .
  1. Remove the watershield.
  1. Remove the interior weatherstrip.
  1. Remove the exterior-weatherstrip.
  1. Remove the nut and the rear window stabilizer.
  1. syh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removing the rivet center pins, place suitable support between the door outer panel and the glass to stabilize the glass.
    NOTE: Lower the window to access the rivets.
    Remove the two rivets retaining the rear door window glass to the rear door window glass run and bracket.
9eaea6b.gif
  1. Remove the rear door window glass.
  1. To install, reverse the removal procedure.

Apr 09, 2009 | 2000 Ford Taurus

1 Answer

'88 toyota camry rear window stuck in down position


To get to the Window:

Remove Door Inside Handle:
remove screw, slide the handle forward.
Disconnect the control link and remove the handle.

Remove Door Trim with Inner WeatherStrip:
Remove the two screws from the armrest.
Insert a screwdriver between the trim retainers and the door panel to pry it loose.  Eight hidden fasteners. 1 top left side of door.
1 right side about same height as top of armrest. 1 (each side) about same height as bottom of armrest. 1 on each corner bottom. 1 bottom in middle.  1 on left side between bottom corner and the previous at about lower armrest height...

Remove Service Hole cover.
Remove Door Glass Run.

Remove Division Bar (upper window section divider):
Remove the two screws under the weatherstrip
Remove the bolt.
Pull out the division bar.

Remove the Window Glass:
Place the glass in the door cavity.
Remove the two glass channel mounting bolts.
Remove the window glass by pulling it upwards.

You now have access to the Power Window Regulator; possible replacement of motor etc.

What type of 'things' have you tried for fixing the window and restoring operation?

Jan 22, 2009 | 1988 Toyota Camry

1 Answer

Rear window regulator line broken


Hi lec the rear glass has a white plastic clip holding the glass to the regulator. try from  the door side, pushing the center plastic pin out toward you then the glass will lift out   D

Jan 15, 2009 | 2000 Jaguar S-Type

2 Answers

Dodge caravan sliding doors


First, keep in mind that as you begin to remove these doors you run the risk of causing serious scratches to the paint and glass, so put some masking tape and/or plastic sheeting around both sides of the door (rear quarter panel and rear glass, front door and front door glass)
I would get a Haynes repair guide since that's what I have to work from and it will tell you step by step with pictures, what to do. It's not hard, but you need to get all of the attach points unhooked to be successful. Suggest you have a helper working with you to keep the door steady.

Oct 27, 2008 | 2005 Dodge Caravan

1 Answer

Glass


is that glass a half pane on the rear door ?

Robert

Jun 11, 2008 | 1995 Honda Odyssey

Not finding what you are looking for?
2000 Jaguar S-Type Logo

876 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

447 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...