Question about 1994 Isuzu Rodeo

1 Answer

Clutch how many bolts are there in the transmission and if they are all out why won't the transmission come of the engine. i am replacing the clutch

Posted by on

  • laurie_conle Oct 18, 2008

    Hi there yes I was pulling my transmission to replace the clutch and I can not get the transmission to back off.I kept thinking that I must have missed a bolt.It is a 1990 isuzu pickup extended cab.So all I have to do is take the pressure off and it should eventually loosen off?



×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 250 Answers

There are quite a few around the bell. It depends on your year exactly how many. If you have all the bolts off and it transmission won't drop it's because it's bound up. Do you have a transmission jack under it? The transmission is very heavy and you won't likely get it back up there without a jack. The jack would also relieve the pressure that is causing it to bind up. Once you relieve that pressure you should be able to slide the transmission back and it'll come loose from the motor.

Posted on Jul 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace a clutch in a 1998-99 Geo metro


why not post symptoms first, (like, my clutch pedal is dead) or?
manual or automatic trans/ both have clutches.?????
metro ended in 97 and was then and a Chevrolet nameplate from 1998 to 2001
metro, is covered in all metro, FSM books
all metro forums
see vast links here
http://www.fixkick.com/swift.html

online:
and at alldata.com
mitchels.
dont know year, ?

my wild guess. on what is there, M/T stick shift car.

M/T stick
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Transmission assembly and matchmark the flywheel to the engine
    • Clutch pressure plate cover by slowly and evenly loosening the bolts until the spring tension is released
    • Clutch disc

Trans out,
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the transmission fluid.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Both front wheels
    • Backup lamp switch electrical connector
    • Clutch release lever from the clutch release shaft
    • Clutch cable bracket and move it aside
    • Negative battery cable and hanger from the transmission
    • Gearshift guide case bolts and set the engine wire harness and bracket aside
    • Speedometer cable
    • Starter motor
    • Two right side upper case-to-engine bolts
  4. Install an engine support fixture.
    • Both drive axles after properly supporting the transmission
    • Flywheel cover
    • Control joint shaft through bolt and separate the control shaft from the control joint
    • Gearshift control lever guide plate and separate the extension rod from the lever guide plate
  5. Support the transmission.
    • Bolts from the rear transmission mount
    • Left side mounting bracket bolts
    • Right side case-to-engine mounting bolts
    • Transmission through the left side of the engine compartment and make certain that the input shaft clears the clutch pressure plate

Feb 14, 2015 | Geo Cars & Trucks

1 Answer

Replace clutch


Disconnect wires and sensors from above (under the hood). Raise car. Disconnect wires and sensors underneath the car. Support the engine and transmission. Loosen or disconnect some motor mounts. Remove the bolts that hold the engine and transmission together. Remove bolts that attach clutch to flywheel. Seperate engine and tranny. Remove clutch. Installation in reverse.

Better directions given if you say what car you're asking about.

Nov 28, 2014 | Cars & Trucks

1 Answer

Mitsubishi lancer my gears wont go into gear or reverse at all


I assume you have a manual transmission. There are three main possibilities:

1. The clutch slave cylinder has failed. Its on the front side of the transmission. If its leaking, replace it. If its not, you should be able to see the actuator shaft move about 12mm or so when someone presses the clutch.

2. If the actuator shaft does not move, the clutch master cylinder has failed. Replace it.

3. If the actuator shaft does move the right distance, there's a problem with the clutch itself, which means removing the transmission and replacing the clutch.

4. Before doing that, pull your battery out and check that the 4 M10 bolts that secure the transmission to the engine are still present. There's two bolts at the top of the trans, and two more at the bottom edge of the engine block.

Nov 10, 2014 | Mitsubishi Lancer Cars & Trucks

1 Answer

Manual trans won,t shift 87f150


When there is an issue with a manual gear box not working after a clutch replacement I am always suspicious that the clutch plate has been fitted the wrong way and the crank bolts are fowling on the cluch plate center . If the gear box was fine before and i now faulty I would go to what was done with the clutch. Also check that the clutck slave cylinder is working ok.

Feb 22, 2013 | 1987 Ford F 150

1 Answer

Remove a flywheel


The clutch come out with the engine since it is bolted to the fly wheel. If you had an automatic transmission then you would need to remove the torque converter bolts from the flywheel so that the torque converter would stay in the transmission. If you pulled the manual transmission the clutch would stay attached to the flywheel. It's the same when pulling the engine.

Aug 07, 2012 | Saturn Vue Cars & Trucks

1 Answer

How to replace the clutch on front wheel drive cars


It is best to replace the clutch driven plate, pressure plate and release bearing at the same time.
You have to remove either the transmission or the engine(or both). On some vehicles it is not possible to remove the engine without the transmission. I prefer removing the transmission only, since it does not require a hoist. (Removing engine and transmission complete is a bit more complicated,theres much more things to disconnect, but makes things easier when mating the transmission to the engine after replacing the clutch assembly). When removing the transmission only make sure the engine is properly supported, since the engine is supported by the transmission and vise versa.
Take note of all pipes and cables that you remove and mark them with masking tape since that gives you something to write a description on. Remember to mark the spot that you disconnect from as well. Taking close-up pictures of the engine bay will work wonders when your memory fails.
Read through this : http://www.fixya.com/cars/t4984410-remove_front_axle_get_engine (solution 2)
Drain transmission oil. Remove the driveshafts as described. Remove any electrical connections to the gearbox.
Remove the gearshift linkage. Remove the clutch cable/clutch operating mechanism(hydraulic clutch) Remember to support the engine before unbolting the transmission from the engine. Remove any mountings still connecting the transmission to the body of the car..
Remove the transmission from the engine bay. It is possible to do this by hand (a helper would be a plus at this point)
The clutch pressure plate is then visible on the engine and held in place by 6 bolts. It can be removed along with the clutch plate(which will drop free once the pressure plate is removed. Replacing the clutch is pretty straightforward, except that the clutch plate needs to be centered, or the transmission wont go back on. Autozone stocks a clutch centering tool which you can purchase although some clutch kits come with the centering tool supplied, else you can fashion one out of a wooden dowel. The dowel needs to fit snugly into the recess in the centre of the flywheel. Use insulation tape to build it up if it is too thin. The clutch plate can go in one way only. You will note that the clutch plate centre has a metal plate fitted on one side. This is the transmission side of the plate. Fit the clutch plate and pressure plate to the flywheel and tighten the bolts just enough to hold the clutch plate in place so that it doesnt move around. Using your centering tool make sure the clutch plate is nicely centered. Then tighten the bolts to the specified torque. Which means tighten them up without breaking them. Get the transmission fitted to the engine. This may take some doing especially if the clutch centering didnt go too well. Now reconnect everything and drive the vehicle to the nearest alignment centre to re-set the wheel alignment.

Jul 07, 2010 | Cars & Trucks

2 Answers

Replace clutch in a 2003 hyundai Elantra


  • The manual transmission in your Hyundai Elantra uses a clutch to engage and disengage the power from the engine to the transmission.
  • The clutch disc is sandwiched between the engine flywheel and the transmission pressure plate.
  • When you switch gears and let off the clutch pedal, there is a short period during which the clutch is slipping to transmit the power in a controlled way. This causes wear on the clutch; over time it will require replacement.
The procedure to replace the clutch is as follows:--- 1) Jack up the Hyundai Elantra and place on jack stands. 2)Drain the transmission gear oil into a catch pan. To drain the gear oil, loosen the drain bolt with a ratchet. 3)Disconnect both drive axles (half shafts) from the transmission. Use a ratchet to remove the two bolts that hold the steering knuckle to the strut. Once those are out, you can easily pull the axles out of the transmission. The steering knuckle is the component that the wheel and strut attach to. 4)You can locate the two bolts to remove by following the strut down from where it's bolted into the engine bay Removing these two bolts allows you to pull the steering knuckle outward so you can pull the drive axle out of the transmission. 5)Remove the exhaust downpipe from the rest of the exhaust. It will be held on with two bolts at both ends and can be removed with a ratchet. Removing this piece is necessary to gain access to the transmission. 6)Disconnect the shifter cables connected to the transmission. Use a ratchet to remove each shifter cable and its housing.Remove the bolts holding the transmission to the engine block (there will be about seven or eight bolts). Place a transmission lift underneath the transmission to hold it and lower it down. If you don't have a transmission lift, you can use a transmission attachment for your jack.Shift the transmission back and forth until it drops onto the jack. Pull the transmission straight back, ensuring that no pressure is put on the input shaft, then lower the transmission to the ground. 7)Remove the pressure plate and clutch disc from the flywheel with a ratchet tool. Then remove the flywheel with a ratchet tool and replace it with a new flywheel. Alternatively, have your flywheel professionally machined at a machine shop then replace it in your car. Torque the flywheel down to the manufacturer's specifications. 8)Place the clutch disc on the clutch disc alignment tool and insert the tool into the flywheel input shaft hole. Connect the new pressure plate to the flywheel and torque the bolts. Once the pressure plate is torqued down, remove the clutch alignment tool. 9)Grease the new throw-out bearing and place it on the input shaft of the transmission. Once the transmission is installed, it will push against the pressure plate. 10) Reconnect all the parts which you removed while replacing the clutch. Thanks. you can rate this solution and show your appreciation.

May 19, 2010 | Hyundai Motor 2003 Elantra

1 Answer

Change transmission instructions


this is for rear wheel drive only front wheel drives require removing axle shat and dropping tie rod end and lower ball joint to get tranny out. If you start this I will give tork setting when I know what you have as it is a lot of work to type this out.

First disconnect the battery, inside the cab pull shifter boot off and remove snap ring to remove shifter, next get a block to go under engine remove drive line bolts and be sure E-brake is set and block the wheels, next put bolts from driveline into the read differential in order so you will be able to find them next disconnect the two starter bolts from the starter and tie starter up as not to allow the starter weight to hang on the wires. Remove two bolts holding slave cylinder on let hang off the side do not lose the shaft out of slave. Next remove the transmission mount bolt out next pull four bolts out of transmission cross member, next remove 5 bolts out of bell housing now get a baggie and a couple of rubber bands and pull drive shaft slide baggie over the transmission tail shaft and put on rubber band on bag to keep from losing fluid move drive shaft out of the way. Next disconnect the Speedo cable and wiring harness the reverse switch is at the top so will have to drop the tranny down to keep from breaking wire. Once you have a gap between the transmission and engine put block under back of engine slide the transmission out let the front drop down then lift up on rear of transmission and slide the cross member out of the way. Next slide tranny out of the way next remove the 6 bolts on the clutch assembly turning each bolt 1 and a ½ turns each till clutch is loose remove the clutch pressure plate and the throw out bearing, remove flywheel take to machine shop and have surfaced, replace the clutch plate pressure plate and the throw out bearing reinstall in reverse if you see any oil leaks replace seals, also replace rear transmission seal now if you don’t it will leak next after it is back together be sure you put new fluid in the transmission and bleed the slave cylinder.

Jun 28, 2009 | Nissan Pickup Cars & Trucks

1 Answer

Need help fitting a clutch on a VW GTI Golf


undo centre wheel hub nut 30mm/32mm, socket. undo lower wish-bone outer bolts, disconect battery,/remove starter motor,/remove transmission mounting bolts to body frame ,/ remove all surrounding bolts around bell housing transmission,/ remove clutch cable from transmission,/ remove drive shafts from centre hub and transmission,/ make sure car is standing on axle stands at front of jacking points,/use a trolley jack to suport engine sump with a piece of wood,/ slide transmission away from flywheel,/lower transmision on floor,/undo all clutch plate preasure bolts 10mm,/remove thrust bearing located on centre transmision shaft ,.also make sure if fitted speedo cable needs to be removed.new clutch plate should indicate flywheel ,without fitting clutch plate wrong way round/otherwise transmision will not bolt to engine block.,

May 17, 2009 | 1999 Volkswagen GTI

3 Answers

How long will it take to repair a 87 suzuki samurai clutch, 4x4


Remove the shifter from inside, two connectors to the sensorson the trans at the firewall, remove 4 bolts holding front driveshaft to the front diff, slide rear section of front driveshaft out of the splines, remove 4 bolts holding rear driveshaft to transfer case and slide the driveshaft out of the transmission tailshaft, remove the two starter bolts ( hardest part of the job), leave the starter in the engine bay with the wires still attached, remove the clutch ARM from the transmission, remove the rear transmission mount (4 12mm bolts) support the transmission on a jack, put another jack in from of the engine to pitch the engine so the rear is sagging down slightly (this is so you have enough clearance to remove the transmission), remove the four 14 mm bellhousing bolts (remember the longer one goes onto the passenger side top) tip the tailshaft up to the floor of the Sammy and slide it to the rear as far as possible, let the front come down slowly ( it will barley rub the pressure plate but not enough to hurt anything) presto its out, replace the clutch assembly and grease throwout and transmission splines the reverse these steps. I have done 3 of these and accomplished my last one in 4 hours total. No need to remove the exhaust, transfer case or engine as others have stated on numerous write ups. You will need two 12mm combo wrenches, one 14mm combo wrench, one 3/8 drive ratchet with 12mm shortwell socket, a couple extensions for said ratchet, one small pair of pliers (to hold the clutch cable while adjusting) and a hammer to gently tap the clutch arm onto the splines.

Apr 28, 2009 | 1987 Suzuki Samurai

Not finding what you are looking for?
1994 Isuzu Rodeo Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...