Question about 1999 Chevrolet Malibu

1 Answer

Wiring diagram for blower motor controls

1999 chevy malibu

Posted by on

  • 2 more comments 
  • naiwlin Nov 13, 2008

    the blower does not work for the first two speed but work for the others speed

  • keeskoster Dec 09, 2008

    Only 3 and 4 position works but I could live with that. The blower motor quit altogether that was seemingly the problem.

    I found that connection on motor itself was intermittend also on the one I bought from carwreckers, I bought 2nd one and secured connector on blowermotor with 2 component glue so that it could not move and break something internally this one worked fine straight on battery and wiggling the connector.

    After putting in that motor stopped again after a short trip and I suspect that my frustastions were caused by 2 problems as it seems what is my second problem I don't know yet..........

  • Anonymous Feb 04, 2009

    I'm having the same problem with my blower motor, But its on a 2000 malibu. I only have one speed that will work and its the highest speed.

  • Anonymous Mar 20, 2014

    Will the 2011 2.4L gasoline motor out of a chevy malibu work in a 1999 chevy malibu also a 2.4L



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,039 Answers

The resistor is bad its beside the blower motor pierre

Posted on Nov 28, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need to replace blower fan motor 2006 Chevy Malibu

2004 and up, the old blower motor must be cut out with a utility knife and the new one screws into the opening to the screw holes molded into the plastic housing. It is located under the passenger side dash, you may have a silencer / plastic cover there you have to remove to view it.
  • Remove the passenger's side lower silencer panel.
  • Remove the blower motor wire harness connector.
    Two diagrams show how it goes:
    Cut along the narrow groove where the arrows indicate. Do not cut too deep, only enough to remove motor, as the cup will be re used.
  • Install new motor assembly with three screws, usually provided with new unit. Tighten securely.
  • Atatch wire harness. Test unit. If functioning properly, replace silencer / cover.
  • Jul 22, 2014 | Cars & Trucks

    1 Answer

    I need a wiring diagram for the blower motor on a 1999 jeep grand cherokee limited. I have two wires sticking out of the blower motor and I don't know where they go

    Usually you have to splice the wires into the old plug.
    You might be able to find a diagram on the websites for auto parts stores such as autozone.

    Jul 06, 2012 | 1999 Jeep Grand Cherokee

    1 Answer

    99 chevy malibu serpentine belt diagram

    There are 2 possible diagrams for your car depending on which engine it has. Both diagrams are listed below:

    1999 Chevy Malibu 2.4L

    1999 Chevy Malibu 3.1L


    Aug 16, 2011 | Chevrolet Chevy Cars & Trucks

    1 Answer

    I need a layout for the resistor for the a/c fan speed control in a '99 Malibu

    I do not have the diagram for you. but i can tell you how to change it! first, its behind glove box. to make things easier remove the glove box. remove insulating pad from underneath glove box, next loosen and slide the ecm to one side. now you can see resistor and blower motor. resistor is beside blower motor. remove wiring to resistor. take out the screws that hold it in. then pull it out of heater box. have a good day !!

    May 17, 2010 | 1999 Chevrolet Malibu

    1 Answer

    Replace blower motor resistor unit on 99 Malibu ?

    the blower motor resistor is below glove box. remove panal under box. slide the pcm out of the way, resistor is beside blower motor. unplug wiring, take out screws holding it in then pull straight out to remove.

    Jul 10, 2009 | 1999 Chevrolet Malibu

    1 Answer

    How do I change the blower motor resistor on a 1999 chevy malibu?

    There should be maybe two screws and the connector sitting by the blower area. A little awkward but not impossible.

    Jul 05, 2009 | 1999 Chevrolet Malibu

    1 Answer

    Blower or resistor on 99 malibu?

    the resistor usualy has good diagrams or go to the libruary n get a service book

    May 16, 2008 | 1999 Chevrolet Malibu

    Not finding what you are looking for?
    1999 Chevrolet Malibu Logo

    1,072 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts


    Level 3 Expert

    77499 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22306 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides