Question about 2002 Honda Odyssey

1 Answer

I want to install new camshaft sensor but cant find the original

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 100 Answers

Camshaft sensor is usually found on the front of engine where the front of the camshaft would be
sometimes these are hard to see as they can be sort of hidden by pulley belts

Posted on Jan 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacement of timing belt on 2001 daiwoo legansa


This should give you a clue as to how to replace the timing belt on the camshaft pulleys.prev.gif next.gif Camshaft and Valve Lifters REMOVAL & INSTALLATION 1.6L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Timing belt
    • Crankcase ventilation tube from the valve cover
    • Spark plug cover bolts and the cover
    • Camshaft Position (CMP) sensor connector
    • Spark plug wires from the plugs
    • Valve cover nuts, washers, cover and gasket
    NOTE: Be very careful not to nick or scratch the camshafts.
  4. Hold the flats of the intake camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  5. Hold the flats of the exhaust camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  6. Mark the camshaft cap locations so that they may be returned to their original positions.
  7. Remove the camshaft cap bolts in the sequence illustrated.
  8. Remove the caps and the camshafts. Fig. 1: Loosen the camshaft cap bolts in this sequence using several passes - 1.6L engine 9307zg85.gif
    To install:
  9. Lubricate the camshafts and caps with engine oil.
  10. Install the caps and the camshafts in their original positions.
  11. Tighten the camshaft cap bolts in the sequence illustrated to 12 ft. lbs. (16 Nm). Fig. 2: Tighten the camshaft cap bolts in the sequence illustrated using several passes - 1.6L engine 9307zg84.gif

  12. Measure the camshaft endplay on both camshafts. The endplay should be 0.003-0.009 in. (0.10-0.25mm).
  13. Install the intake camshaft gear. Hold the flats of the intake camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 49 ft. lbs. (67 Nm).
  14. Install the exhaust camshaft gear. Hold the flats of the exhaust camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 49 ft. lbs. (67 Nm).
  15. Apply a small amount of gasket sealer to the corners of the front camshaft caps and to the top of the rear valve cover-to-cylinder head seal.
  16. Install or connect the following:
    • Valve cover, washers and nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
    • Spark plug wires to the plugs
    • Spark plug cover and bolts. Tighten the bolts to 27 inch lbs. (3 Nm).
    • CMP sensor connector
    • Crankcase ventilation tube to the valve cover
    • Timing belt
2.0L and 2.2L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Timing belt
    • Crankcase ventilation tube from the valve cover
    • Spark plug cover bolts and the cover
    • Spark plug wires from the plugs
    • Camshaft Position (CMP) sensor connector
    • Valve cover nuts, washers, cover and gasket
    NOTE: Be very careful not to nick or scratch the camshafts.
  4. Hold the flats of the intake camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  5. Hold the flats of the exhaust camshaft in position using an open ended wrench and remove the camshaft gear bolt. Remove the gear.
  6. Mark the camshaft cap locations so that they may be returned to their original positions.
  7. Remove the camshaft cap bolts in several passes of one half turn each in the sequence illustrated.
  8. Remove the seal ring from the camshafts. NOTE: Make sure the camshafts detaches evenly from the bearing seats in the front guide bearing.
  9. Remove the caps and the camshafts. Fig. 3: Remove the camshaft cap bolts in several passes of one half turn each in the sequence illustrated - 2.0L and 2.2L engines 9307zg38.gif
    To install:
  10. Lubricate the camshafts and caps with engine oil.
  11. Install the caps and the camshafts in their original positions.
  12. Tighten the camshaft cap bolts in the sequence illustrated to 71 inch lbs. (8 Nm). Fig. 4: Tighten the camshaft cap bolts in the sequence illustrated using several passes - 2.0L and 2.2L engines 9307zg37.gif

  13. Measure the camshaft endplay on both camshafts. The endplay should be 0.0015-0.0056 in. (0.040-0.144mm).
  14. Install the intake camshaft gear. Hold the flats of the intake camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 37 ft. lbs. (50 Nm), retighten the bolt an additional 60 degree turn and finally an additional 15 degree turn.
  15. Install the exhaust camshaft gear. Hold the flats of the exhaust camshaft in position using an open ended wrench and tighten the camshaft gear bolt to 37 ft. lbs. (50 Nm), retighten the bolt an additional 60 degree turn and finally an additional 15 degree turn.
  16. Install or connect the following:
    • Valve cover, washers and nuts. Tighten the nuts to 71 inch lbs. (8 Nm).
    • CMP sensor connector
    • Spark plug wires to the plugs
    • Spark plug cover and bolts. Tighten the bolts to 27 inch lbs. (3 Nm).
    • Crankcase ventilation tube to the valve cover
    • Timing belt
    • Negative battery cable

Feb 04, 2011 | 2001 Daewoo Leganza

1 Answer

Can you explain how to replace a cam shaft censor on my 300m 99


Welcome to FIxYa.com


The camshaft position sensor is installed in the timing belt housing cover above the left camshaft sprocket.

Removal:

1. Disconnect the negative battery cable.

2. Remove the upper intake plenum.

3. Disconnect electrical connector from sensor.

4. Remove camshaft position sensor bolt.

5. Pull sensor up out of the timing belt housing.



Installation:

If the removed sensor is reinstalled, remove the old spacer from the sensor face, Attach a

new spacer to the face of the sensor.



If installing a new sensor be sure that the paper spacer is attached to the face.

1. Install sensor in the timing belt housing and push down until contact is made with the camshaft sprocket. While holding down in position, install and tighten bolt to 12 N.m(105in.lbs) torque.

Hook up electrical connector.

Connect Negative battery back up.

leedavidian_13.png


Regards, Lee Davidian


Thank you for using FixYa.com

Nov 05, 2010 | 1999 Chrysler 300M

2 Answers

Where is the camshaft position sensor located on a 1997 Oldsmobile Cutlass Supreme 3.1 ?


Removal & Installation 3.1L Engine To Remove:
CMP sensor 93174g24.gif

  1. Disconnect the battery ground cable.
  2. Remove the power steering pump and set aside with the lines connected.
  3. Disconnect the camshaft position (CMP) sensor electrical connector.
  4. Remove the CMP mounting bolt.
  5. Remove the CMP sensor.
  6. Check the O-ring for damage and replace if necessary.
To Install:
NOTE: Lubricate the O-ring with clean engine oil.
  1. Install the camshaft position sensor.
    • Tighten the mounting bolt to 89 in lb (10 Nm).
  2. Connect the CMP sensor electrical connector.
  3. Install the power steering pump.
3.4L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Detach the electrical connector from the camshaft position sensor.
  3. Remove the sensor retainer bolt and carefully pull the sensor from the camshaft carrier. An O-ring seal may hold the sensor in place. Use care not to lose the O-ring.
Camshaft Position (CMP) sensor removal (3.4L (VIN X) engine) 93174g25.gif

To Install:
  1. Installation is the reverse of the removal procedure.
  2. Before installing a replacement camshaft sensor, lubricate the new O-ring with clean engine oil.
    • Tighten the bolt to 88 inch lbs. (10 Nm). Do not over-tighten.
  3. Connect the negative battery cable.
3.8L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Detach the electrical connector from the camshaft position sensor. Camshaft Position Sensor removal (3.8L engines) 93174g26.gif

  3. Remove the retaining screw and separate the sensor from the front cover.
To Install:
  1. Installation the sensor in the front cover.
  2. Tighten the bolt to just 44 inch lbs. (5 Nm). Do not over-tighten. Verify the electrical connector is secure.
  3. Connect the negative battery cable.
prev.gif next.gif

Aug 26, 2010 | 1997 Oldsmobile Cutlass Supreme

1 Answer

I need to find the camshaft position sensor on my 2003 nissan murano


Camshaft Position Sensors are located on the cylinder head according to the following: Camshaft, Bearings & Lifters Removal & Installation To Remove:
  1. Remove the engine from the vehicle.
  2. Remove the front suspension member, transaxle and transfer case (if equipped) from the engine.
  3. Mount the engine in a suitable engine stand.
  4. Remove the timing chains and rear timing chain case.
  5. Remove the camshaft position sensors from the cylinder heads.
  6. Remove the intake valve timing control solenoid valves. NOTE: Mark the camshafts, camshaft brackets, and bolts so they are placed in the original locations during installation.
  7. Loosen the camshaft bracket bolts in several steps using the order shown.
  8. Remove the intake and exhaust camshaft brackets and the camshafts. Camshaft bracket bolt removal sequence nissan-03-35-4624.gif

  9. Remove the valve lifters and the secondary timing chain tensioner with stopper pin attached if necessary.
NOTE: Stopper pin was installed when the secondary timing chain was removed.
To Install:
NOTE: Clean sealant from front camshaft bracket, bolts and bolt holes.
  1. Turn the crankshaft until No.1 piston is at TDC on the compression stroke. The crankshaft key should line up with the right bank center line as shown. Crankshaft keyway position nissan-03-35-4625.gif

  2. If removed, install the secondary timing chain tensioners and valve lifters in their original positions. NOTE: The intake camshaft has a drill mark on the edge of the sprocket mounting flange.
  3. Position the camshafts on the cylinder heads with the dowel pins as shown. Camshaft dowel pin positions nissan-03-35-4626.gif

  4. Apply silicone sealant to the front (No. 1) camshaft bracket as shown. Apply silicone sealant to the front (No. 1) camshaft bracket nissan-03-35-4627.gif

    Camshaft bracket bolt installation sequence nissan-03-35-4628.gif

  5. Install and tighten the camshaft brackets using the following steps in the sequence shown;
    • Step 1 (bolts 7 - 10) : 1 ft-lb (2 Nm)
    • Step 2 (bolts 1 - 6) : 1 ft-lb (2 Nm)
    • Step 3 (bolts 1 - 10): 4 ft-lbs (5.9 Nm)
    • Step 4 (bolts 1 - 6) : 8 ft-lbs (10.4 Nm)
    • Step 4 (bolts 7 - 10) : 7 ft-lbs (9.3 Nm)
  6. Wipe off excess sealant from bracket No. 1.
  7. Measure the difference between the front surfaces of camshaft bracket No. 1 and the cylinder head. The specification is -0.0055 to 0.0055 in (-0.14 to 0.14 mm). Replace the camshaft and camshaft bracket if out of specification. Measure the difference between the front surfaces of camshaft bracket No. 1 and the cylinder head nissan-03-35-4629.gif

  8. Install the IVT control solenoid valves with new gaskets.
  9. If removed, install the camshaft position sensor.
  10. Install the rear timing chain case and timing chains.
  11. Install the engine in the vehicle.
prev.gif next.gif

Jul 03, 2010 | 2003 Nissan Murano

1 Answer

2000 ford tauras,auto,84k miles, small v6, missing between 45 & 55 mph. Under & over no missing noticed. spark plugs changed @ 70k. Original wire and sensors; as shop said very good. Suggestions...


Sounds like it could be a cam position sensor.



2000 Ford Taurus V6-3.0L DOHC VIN S
Camshaft Position Sensor: Service and Repair
REMOVAL
1. Disconnect the battery ground cable. For additional information, refer to Battery.
2. Remove the Camshaft Position (CMP) sensor.
1 Remove the electrical connector.
2 Remove the bolt and the CMP sensor.
INSTALLATION
1. To install, reverse it removal procedure
1. To install, reverse the removal procedure.

Sep 06, 2009 | 2000 Ford Taurus

1 Answer

1993 ford taurus, replaced all starting and charging componets still no spark to plugs. Checked all fuses and all fusible links. Replaced key switch, ignition switch,neutral safty...


The camshaft position sensor sends a signal to the PCM, powertrain control module. The PCM then determines spark plug firing. Could be the camshaft position sensor.

1996 is all I have
Camshaft Position (CMP) Sensor 3.0L (2V) Engine
The camshaft position sensor (CMP sensor) (12126):
  • is a single Hall-effect magnetic switch activated by a single vane which is driven by the camshaft (6250).
  • provides camshaft position information which is used by the ignition coil (12029) and the powertrain control module (PCM) (12A650) for fuel synchronization.
3.0L (4V) Engine
The camshaft position sensor (CMP sensor) (6B288) is:
  • a variable reluctance sensor.
  • triggered by the high-point mark on the LH exhaust camshaft sprocket (6256).
-----------------
3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder block.
Installation
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 75 degrees counterclockwise from the rear face of the cylinder block. This step will locate camshaft position sensor electrical connector in the pre-removal position.
  1. Roatate Syncro Positioning Tool T95T-12200-A clockwise slightly. This will engage oil pump intermediate shaft. Push downward while adjusting Syncro Positioning Tool T95T-12200-A until the Syncro Gear engages the camshaft gear.
  1. When synchronizer flange is fully seated against block, the installation tool should be facing counterclockwise of engine centerline approximately 33 to 45 degrees.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (13-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.
824fa44.gif
Item Part Number Description 1 T95T-12200-A Syncro Positioning Tool 2 — Water Outlet (Part of Intake Assy) 3 9424 Intake Manifold 4 N602704-S Screw and Washer 5 12126 Camshaft Position Sensor 6 12A362 Synchronizer Assembly 7 12270 Hold-Down Clamp A — Tighten to 1.5-4 Nm (13-35 Lb-In) B — Tighten to 19-30 Nm (14-22 Lb-Ft)

Apr 04, 2009 | 1993 Ford Taurus

1 Answer

Where is located the camshaft sensor on a dodge sx 2.0 2003?


camshaft sensor located on end of cylinder head near battery..remove battery..4 bolts and wire connector..clean mounting surface and install new sensor

Mar 14, 2009 | 2003 Dodge Neon

1 Answer

Remove the camshaft position sensor from my 1999 jeepcherokee


The Camshaft Position Sensor (CMP) on the 4.7L V - 8 engine is bolted to the front side of the right cylinder head. Disconnect the sensors connector. Take out the bolt that holds the sensor in place. Lightly pry out the sensor being careful not to break it. Clean out the hole and install the new sensor( put a little oil on the new sensors o-ring to help installation).

Feb 26, 2009 | 1999 Jeep Grand Cherokee

1 Answer

1997 mercury sable camshaft sensor replacement


do you have 3.L 2v or 4 valve?

3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder blocks (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (12270) (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder blocks.
Installation
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be used to position the synchronizer assembly prior to installation of the camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs. Locate camshaft position sensor electrical connector in the pre-removal position.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (14-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.

Feb 22, 2009 | 1997 Mercury Sable

1 Answer

Cant find cam sensor in 2004 dodge stratus r/t


2.0L 2.4L it is on The BACK OF the Cylinder Head REMOVAL
The camshaft position sensor is mounted to the rear of the cylinder head.

  1. Remove the negative battery cable.
  2. Disconnect the PCV hose and reposition.
    1. Disconnect electrical connectors from the camshaft position sensor.
    2. Remove camshaft position sensor mounting screws. Remove sensor.
      1. Loosen screw attaching target magnet to rear of camshaft and remove magnet.
      INSTALLATION
      The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.

      1. Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
      2. Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
      3. Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins.
      4. Connect the PCV Valve hose.
      5. Connect the negative battery cable.
2.7L V6
REMOVAL
The camshaft position sensor is mounted in the front of the head.
  1. Disconnect electrical connector from sensor.
  2. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
  1. Without pulling on the connector, pull the sensor out of the chain case cover.
INSTALLATION
The camshaft position sensor is mounted in the front of the head.

  1. Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
  2. Attach electrical connector to sensor.

Feb 12, 2009 | 2004 Dodge Stratus

Not finding what you are looking for?
2002 Honda Odyssey Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...