Question about 1987 GMC Suburban

1 Answer

Just put 454 in my 1987 truck and looks like the crankshaft pulley is off could it be the wrong pulley for the year?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 100 Answers

When you say pulley loks like it is off, are you referring to the timing marks not ligning up?
if this is what your talking about, it is more likely that the distributor has been installed a notch or two wrong

Posted on Jan 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is crankshaft position sensor


usually down by the crankshaft pulley, the one the serpentine belt spins around down low. look for something electrical.
25439652-xipalmoknr3fbjmp51kycajc-1-0.jpg if its a nissan, change the starter. no lie. They are in the wrong place on nissans.
25439652-xipalmoknr3fbjmp51kycajc-1-1.jpg

Feb 16, 2015 | Cars & Trucks

1 Answer

2005 santa fe serpentine broke then bad vibrating and it died replaced serpentine and tensionor, now motor locked. Is the motor shot or could something else be wrong?


Put a socket and wrench on the crankshaft pulley bolt, and see if you can turn the crankshaft-clockwise. If the crank won't turn, something internal is bad. If you can turn the crankshaft normally, check that another pulley has seized.
Or try it this way: take the serpentine belt back off and see if the starter can spin the crankshaft. If it does, look for a seized pulley. If a good battery cannot make the starter turn the crankshaft, likely the motor is shot.

Aug 15, 2014 | 2005 Hyundai Santa Fe GLS

3 Answers

I need to remove my front seal ( crankshaft) possibly without any fancy tools?


Pulling and replacing a main seal on a crank cannot be done without "fancy" tools. If you go to www.autozone.com and make a free account and then put in the make and model and year, you will be able to access the free online repair guides. Also if there is an autoparts chain near you, you can rent those fancy tools.

Dec 05, 2012 | Cars & Trucks

1 Answer

Looking for scheme of fan belt for audi a6 2.5 tdi 150 bhp 1999 year Thanks


The fan belt routing scheme for Audi A6, 2.5 TDI, 150 HP, MY 1999

564eb29.jpg
CS = Crankshaft
F = Fan pulley
Gen = Alternator
G = Guide pulley

T = Tensioner pulley
AC = Air Conditioning
PAS = Power Assisted Steering

Oct 16, 2010 | Audi A6 Cars & Trucks

2 Answers

I need to know where the crankshaft position sensor is located on my jeep grand cherokee


The crankshaft position sensor is located around the crank. Look for a stubby piece of plastic aimed at the edge of the crank pulley. The crank pulley is in central pulley which all the belts are ultimately driven from. It will be in the center-line & bottom of the front of the engine. Typically they are ~45deg off to a side. It's possible you may not be able to remove it without first removing the crank pulley.

Jul 05, 2010 | Cars & Trucks

1 Answer

My crankshaft is very wobbley and make a very high pitched squeak


You need a harmonic balance. Very common problem!

May 21, 2010 | 1995 Geo Prizm

1 Answer

Jsut want to know where crankshaft position sensor


Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Apr 15, 2010 | 2002 Ford Escape

2 Answers

I am having trouble removing the crankshaft pulley are there any hints.


1. Remove the Center Bolt and Washer.
2. Use a correct size Puller - available at most auto parts stores (some even rent them "for free" (with deposit); also available in sets at Harbor Freight.
3. DO NOT USE the outside Crankshaft Pulley lip- the Puller will snap the edge off!
4. Use a smaller sized Bolt inserted where the Crankshaft Bolt was, and use a set of washers small enough to fit on the bolt, but small enough to allow the Crankshaft Pulley to be "pulled" off the Crankshaft. The Puller Pivot Leg will be place againsgt this bolt.

Click on the following free direct Link. It has the Diagrams that may prove helpful in your work.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

http://www.2carpros.com/car_repair_information/year/2003/make/hyundai/model/santa_fe/2003_hyundai_santa_fe_timing_belt_diagram_marks.htm

Mar 16, 2010 | 2003 Hyundai Santa Fe

2 Answers

I am trying to locate the crankshaft sensor on a 92 pontiac bonneville se


It is by the crankshaft pulley.It is behind the pulley and you have to remove the pulley to replace it.There is a special tool for installing the new one.If you look through the pulley you should be able to see it.Hope this helps.Good luck.

Feb 24, 2010 | 1992 Pontiac Bonneville

2 Answers

When i start the car, making loud squeaking sounds


do not add oil to belts. remove belt and spin all pulleys (except crankshaft pulley) any pulley does not turn freely (except crankshaft pulley) is where you will find your problem

Jun 29, 2009 | 2000 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...