Question about Chrysler Crossfire

1 Answer

Headlights only working in bright mode chrysler crossfire any way to fix this?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Chrysler Master
  • 442 Answers

Check fuse panels for low beam fuses high and low beam are normally separately fused ,if that checks out most likely your mutifuction switch

Posted on Jan 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can the 2005 Chrysler Crossfire Limited Coupe automatically turn on the low beam head lamps at night?


No. It has auto lamps.all newer vehicles have them. Some you can turn off. You have to have the light switch in the dash. If it is in the turn signal switch/ column. Your out of luck.

Dec 04, 2014 | 2005 Chrysler Crossfire

1 Answer

I need to see a diagram on how to replace headlight harness connector that is located inside the headlight on 2004 chrysler crossfire


Pull the rubber dust cover back you will see the electrical wires going to the bulb you can pull the old connector off from there it is not inside the housing, the bulb is held in by a small spring clip at the back of the bulb socket.

Sep 06, 2014 | 2004 Chrysler Crossfire

1 Answer

How do you replace the Drivers Side Headlight (bulb?) for 1998 Chrysler LeBaron (there is a coolant reservoir right behind the light assembly under the hood :(


Raise the hood and look at the headlight assembly from the top, you should see a couple of pins to remove and pull them up...the headlight assembly should come out. then just remove the plug and replace the bulb

May 26, 2014 | 2004 Chrysler Crossfire

1 Answer

Went to buy an 05 Chrysler Crossfire Convertible from a used car dealer. He was replacing the spring in the key fob. When he tried to start the car, the engine turn over then stop. When tried again nothing...


Try using a code reader to reset the CPU and have him reprogram the key correctly as well. Personally I would not buy a car from this person until he had everything fixed properly.

Jan 10, 2014 | 2005 Chrysler Crossfire

1 Answer

How do I remove the headlight cover from 2005 crossfire to clean the precipitation


they are sealed units and not meant to be taken apart, if there is moisture inside it means there is a crack or hole somewhere allowing it in, look for anywhere moisture can get in and seal it, the moisture that is there now will dry up over time.

Oct 14, 2012 | 2005 Chrysler Crossfire

1 Answer

I'm having a problem removing the headlight assembly from my 2004 chrysler crossfire, i've removed the 2 screws from the top and removed 1 from below through the wheel well, are there two screws...


Last I checked Chrysler had changed it's headlight mounting from external screws to just the two adjusting screws. Looking down from the top, you should be able to see two Torx head screws that are used to adjust the headlight assembly. The remove teh head light assembly you remove those and the assembly should come right out. Both of these screws or adjusters will be 6 to 8 inches long. I hope your not removing this to change the headlight it self. Chrysler has been using the insert bulbs for several generations and to replace the bulb you only have to unlock the collar on the back of the light assembly and pull and then replace the bulb.

May 14, 2011 | 2004 Chrysler Crossfire

1 Answer

Passenger side headlight assembly removal, is there more than 2 bolts, if so where


You can replace the headlights on your Crossfire easily by yourself. headlight image by Carbonbrain from Fotolia.com

When a headlight burns out on your Chrysler Crossfire, you do not need to rush to the repair shop to have it replaced. You can access the headlights in your Crossfire from within the engine compartment, allowing you to change the headlight yourself. The Crossfire uses an H7U headlight bulb, which you can find at auto parts retail stores or at a Chrysler dealership.
Difficulty: Easy

  1. 1 Open the hood of your Crossfire to gain access to the headlight assemblies. Press down on the tab on top of the light assembly cover. Remove the cover and set it aside.
  2. 2 Pull the electrical connection free of the bulb socket. Press the spring clamps securing the bulb into the light assembly. Pull the bulb straight out of position.
  3. 3 Insert the new bulb in the same position. Ensure that the spring clamps secure the bulb. Press the electrical connection into place.
  4. 4 Replace the light assembly cover and press it into position until it clicks, securing it in place. Repeat the same process on the opposite headlight if required. Close the hood and test the headlight operation.



Dec 12, 2010 | 2004 Chrysler Crossfire

1 Answer

I just replaced the battery in my 2005 Chrysler Crossfire and the engine still will not even turn. Just clicking sounds. Does this battery need to be charged first?


Normally, they are pre-charged at the store. To check, turn on the headlights--they should glow brightly without dimming over a short time. From the symptoms, you have either a bad starter or starter solenoid. You need a test light or meter to make this check--test for power at the starter motor terminal. If the light comes on when the key is turned, the starter motor is defective. If no light, then the high-current contacts in the solenoid are defective. Replacing the defective part should get you running again. Good luck!

Oct 02, 2010 | 2005 Chrysler Crossfire

2 Answers

2004 Chrysler Crossfire won't start. Drove in


This is not the problem I have a chrysler crossfire and experienced the same problem there is some good news if it frequently stops working for no reason the problem is most likely the RCM module has a shortage in it I fixed my crossfire and 3 others buy repairing the RCM its easy and simple any question you can email me I can give you a easy walk through to fix the problem and avoid paying hundred at the dealership it shouldn't take no more than 15 minutes to fix DIY!!

Apr 05, 2010 | 2004 Chrysler Crossfire

2 Answers

Headlights shut off when I turn on the brights.


Your bright bulbs are probably burn out. And yes they can both burn out at the same time, its rare but not as rare as some think

May 14, 2009 | 2000 Chrysler Concorde

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...