Question about 1993 Oldsmobile Cutlass Ciera

Open Question

How do I replace spark plugs on a '93 cutlass ciera?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: repalce front driver power window motor - 1993 cutlass ciera

Disconnect the battery negative cable, carefully remove the door panel, make sure you remove all the visible hold down screws holding the arm rest and other things in place, be careful and observant, don't force anything. If you don't have the standard door panel removal tools, use a stiff putty knife or a wide screwdriver to remove the door panel, you will have to get the power window control switch and the lock control rods out of the way, take notes so you know how they go back together, Remove the plastic weather protection shield out of the way, try not to tear it because you will want to replace it using a good contact adhesive. Getting the motor and the lift mechanism out is the biggest challenge, There are two big rivets holding the motor and regulator assembly to the door, there are two more rivets closer to the rear of the door that holds the track and window guide in place. the rivets are difficult to drill out because it's not easy to center punch them. I used my 4 inch grinder to remove the rivet heads, be careful not to injure yourself or grind through the door metal. knock the rivets out. Remove the power supply wire from the motor. Use a 10 MM socket to untighten the two cap screws that hold the lift bracket to the bottom glass channel. Don't take the cap screws all the way out. Use a piece of wire to hold the window in the closed position. Loop the wire over one of the hold down cap screws and fasten the other end through one of the convenient holes near the top of the door. Now comes the good part. the motor and lift mechanism is all in one near rigid piece. The seat belt anchor blocks the door panel opening that would make it relatively easy to remove. Don't give up, the unit will come out with some thoughtful manipulation, the V shaped track guide will tolerate a small amount of flexing, don't overdo it. I finally got the assembly out by moving it as far to the back of the the door cavity as possible, use the angles of the assembly to your advantage to free it from the door. Once free, use a black marker to ensure you align your new motor in the correct postition. If you are replacing a complete assembly that looks the same a the part you removed, install by reversing the above directions. If you are replacing only the motor, drill out the two rivets that hold the motor to the lift assembly. this will be asy to do. fit your new motor in the exact same position, referring to the previous marks you made. If you are reusing the old lift mechanism, you should pull the perforated tape out of the guide, clean, inspect it, the guide and the tape, relubricate it, I used white grease, there is probably a better grease available. The motor assembly I received from an internet supplier came with rivets and machine screws to install the assembly, I used 1/2 quarter twenty nuts and bolts to replace the big rivets, I don't have a big enough rivet gun. If you go the quarter twenty way, use thread lock, install with bolt heads on the inside the door and flat washers and nuts to the car interior. Be observant, I left the plastic bracket that attaches the drive tape to the window bottom in an unsecure place, one of my dogs used it as a chew toy,so it was off to the junkyard one more time. Be sure to secure the tape properly at both ends. If it worn or frayed, several suppliers including rockauto supply them at reasonable cost. good luck.

Posted on Oct 10, 2008

Ad
  • 1 Answer

SOURCE: STARTER - 1993 cutlass ciera

According to Chilton's, and assuming you have the 3300 V-6, it won't be fun. The first instruction is to drain the air conditioning system, and remove the front manifold. The starter is between the engine and the radiator. The deal breaker for me is the A/C draining/refill. If anyone knows of a way to avoid the A/C drain, let me know. Otherwise, I may just preemptively replace mine before my buddy runs low on R-12.

Posted on Nov 13, 2008

  • 51 Answers

SOURCE: changed spark plugs and wires now car wont start

I know this might be obvious but the obvious is often the problem. Did you replace the coil wire that goes from your coil to the distributor cap? Also, double check to be sure that your wires are connected in the correct order. A little more clarification might help. Does it turn over? Does it just click? When you turn the ignition key then let off does the car clunk or make a wheezing sound?

Posted on Jan 30, 2009

dumbtrucker
  • 102 Answers

SOURCE: 92 olds ciera won't start

Johnny, It's probably the coil pack. If you follow the spark plug wires backwards from the plugs it will lead you to the part(s). There may be more than one. Check with the local autoparts place to see if they can test it for you. If not I would try a Junk yard first, incase that isn't the problem.

Posted on Apr 05, 2009

  • 1 Answer

SOURCE: where is the flasher located on my 93 olds cutlass

can you help me find the flashers are at

Posted on Apr 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the spark plug gap for the above car which is 4 cylinder. thanks


1988 Oldsmobile Cutlass Ciera, original GM plug gap .045".
this is what i would gap new plugs too, AC Delco Part # R44LTS plugs probably gaped at this already.
press the helpful button

How To Change Spark Plugs on 1987 Cutlass Ciera SL 3 8L

Spark Plug Gap NGK Spark Plugs Tech Video

How to Gap Spark Plug

How to Gap Spark Plug

Feb 04, 2016 | 1988 Oldsmobile Cutlass Ciera

2 Answers

What makes the fuel pump not kick on on a 92 Oldsmobile Cutlass


There is a red wire close to the battery in the front. It's not connected to anything. Apply positive voltage and that will run your pump for testing purposes.

Dec 08, 2015 | Oldsmobile Cars & Trucks

1 Answer

Would the mass air flow sensor make my 93 cutlass ciera c stall and then start later


that is possible pehaps you should check code jump aldl and read light for code dirty air filters can cause problems check harness connector also

Apr 30, 2012 | 1992 Oldsmobile Cutlass Ciera

2 Answers

Need help in replacing spark plugs on a 1995 olds cutless ciera the wiring order with diagram


1995 Oldsmobile Cutlass Ciera 3.1 liter V-6 VIN "M"

zjlimited_352.gif


1995 Oldsmobile Cutlass Ciera 2.2 liter L4 VIN "4"

zjlimited_353.gif


Hope this helps (remember to rate and comment this answer).

May 09, 2011 | Oldsmobile Cutlass Ciera Cars & Trucks

1 Answer

Changing spark plugs on a 1995 Oldsmobile Cutlass Ciera


ALL YOU NEED IS 3/8 RATCHET WITH A 5/8 SPARK PLUG SOCKET.YOU NEED EXTENSIONS AND UNIVERSAL JOINTS TO GET TO HARD TO REACH PLACES.YOU NEED A SPARK PLUG GAUGE.YOUR SPARK PLUG GAP SETTING WILL BE. 0.060 THAT WILL BE FOR THE 2.2 AND 3.1 ENGINES.

Aug 17, 2009 | 1995 Oldsmobile Cutlass Ciera

2 Answers

1988 3.8 olds cutlass Ciera stalls, no spark until it cools down


Check the prrimary and secondary resistance on your coil. Also check the resistance of the plug wires and plug gap.

Aug 12, 2009 | 1988 Oldsmobile Cutlass Ciera

1 Answer

How do I change the bulb/headlight on a 93 olds cutlass ciera


behind ur headlights u should c the plug with wires it unscrews by hand counter clock wise

Apr 08, 2009 | 1993 Oldsmobile Cutlass Ciera

1 Answer

92 olds ciera won't start


Johnny, It's probably the coil pack. If you follow the spark plug wires backwards from the plugs it will lead you to the part(s). There may be more than one. Check with the local autoparts place to see if they can test it for you. If not I would try a Junk yard first, incase that isn't the problem.

Apr 01, 2009 | 1992 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1993 Oldsmobile Cutlass Ciera Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...