Question about 2004 Dodge Ram 2500

Open Question

2004 dodge cummings turbo diesel truck is cutting out at hights greater than 1000' at RPM's over 1800

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

freetek
  • 5568 Answers

SOURCE: Nissan 3.0 Hardbody Turbo Diesel

Your description sounds like a waste-gate problem.
These are intended to prevent overpressure from the turbo and yours might be faulty.

The oil leaks may not be related to the other problem - Jeez, would love to own some vehicle that never leaks oil from somewhere.

Posted on Jul 09, 2008

MomsyKat
  • 52 Answers

SOURCE: 99 dodge ram 3500 5.9 turbo diesel fuel problem

Did you check the fuel filter? It can be cleaned out manually. I just hold it to my mouth and blow but make sure the gunk-side is away from you.

Posted on Aug 27, 2008

  • 29 Answers

SOURCE: Charging problem on 1996 Dodge Ram 3500 Cummins Turbo Diesel

I had the same problem on a 94 dodge with the cummins. It seems the crank sensor that reads from a notch on the harmonic balancer was the problem Without this sensor reading that the engine is running the alternator wont charge. Possibly the same problem with yours

Posted on May 03, 2009

  • 66 Answers

SOURCE: I am looking for the I.A.T. Sensor location on my truck

If your looking for the Intake Air Temp/Manifold Absolute Pressure sensor (IAT/MAP)(2003 model year and up) It is on the top of the intake manifold, just to the left of the #3 injector fuel line. There are 2 small Torx screws holding it.

Posted on May 27, 2009

co7196
  • 3433 Answers

SOURCE: how do you remove the flywheel when replacing the clutch

Take trans out, clutch out, and remove the flywheel bolts.

Posted on May 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have code p3202 coming up on my 04 jeep liberty


never heard of google. or an fsm ?
no engine stated
no transmission
dang that makes help hard, we are blind here, unlike you or your mechanic.

i look in my FSM and there is no P3 codes. so did Autozoned do this?
i see only one car showing that code
a Diesel Cummings.
Dodge Cummins Turbo Diesels.

surely you know what under the hood and what transmission is in the car.???

Oct 18, 2014 | 2004 Jeep Liberty

1 Answer

D3500 dually diesel has rough running problems for about ten minutes. Then runs great. Smoke is blue/white at first and truck wont run over 1800 rpm for ten minutes; then runs fine. I am told that it is...


I would look more at your injector pump than the lift pump....Dodge does have a problem with there fuel delivery ( not enough consistent PSI ) which in turn takes out the injector pump mainly because the pump has be running to lean...So look at replacing your delivery pump with something 14PSI or greater, unfortunately sounds as though you will have to get your injector pump either replaced or rebuilt

Dec 31, 2010 | 2002 Dodge Ram 3500 Truck

1 Answer

Need instructions on how to replace water pump on 92 dodge ram 2500, 5.9 diesel turbo cummings


  1. Disconnect the negative battery cable.
  2. Drain the coolant.
  3. Use a 3 / 8 in. drive breaker bar to lift the belt tensioner and remove the belt.



0900c15280070771.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 12: Always install a new O-ring in the diesel water pump

  1. Remove the two water pump retaining bolts and remove the pump from the engine.
  2. Remove the O-ring from the pump groove.

To install:
  1. Clean the O-ring groove and install a new O-ring.
  2. Clean the pump mating surfaces and install the pump to the engine.
  3. Tighten the mounting bolts to 18 ft. lbs. (24 Nm). Fill the radiator with coolant.
  4. Install the drive belt.
  5. Connect the negative battery cable, run the vehicle until the thermostat opens, fill the radiator completely and check for leaks.
  6. Once the vehicle has cooled, recheck the coolant level.

Dec 24, 2010 | 2004 Dodge Ram 2500

1 Answer

FUEL IN OIL PAN


There is a good chance that one of the injectors are leaking and needs to be replaced. It's common on the cummings for the injectors to leak if there is a lot of idle time. Good luck and keep me posted. 

Jun 27, 2009 | 2004 Dodge Ram 3500 Truck

1 Answer

How do you remove the flywheel when replacing the clutch


Take trans out, clutch out, and remove the flywheel bolts.

May 30, 2009 | 2007 Dodge Ram 3500 Quad Cab Laramie

1 Answer

I am looking for the I.A.T. Sensor location on my truck


If your looking for the Intake Air Temp/Manifold Absolute Pressure sensor (IAT/MAP)(2003 model year and up) It is on the top of the intake manifold, just to the left of the #3 injector fuel line. There are 2 small Torx screws holding it.

Apr 05, 2009 | 2004 Dodge Ram 3500 Truck

1 Answer

2002 duramax will heat up underload but not at idle any ideas why


No diesel I have ever owned will heat up to operating temp while idling. I have had semi's and dump truck and a Dodge with a Cummings turbo diesel. If you don't idle a diesel up to around 1200 rpm while sitting the combustion chamber temperature will drop because the diesel does not ignite fully at low rpm. You may also notice after an extended period of idling 1/2 hour or more that when you pull away the exhaust will be whitish blue because of the unburnt diesel fuel sitting on top of the rings. Also extended low idle will wash down the cylinder walls with unburnt diesel and remove the oil from lubricating the cylinders and rings. Hope this helps you understand why your diesel won't heat up while idling. Mike

Jan 06, 2009 | 2002 GMC Sierra

1 Answer

RPM Oscillating


have you had the vehicle speed control reprogrammed if not that could be your problem

Jun 26, 2008 | 2005 Dodge Ram 3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...