Question about 2003 Jaguar S-Type

1 Answer

Ihave a 2003 Jaguar S-Type, What do PO133, PO153 and P1000 codes mean? Afriend said oxygen sensors; how to change the oxygen sensor for a 2003 Jaguar S-Type?

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,400 Answers

You might check this site out for Jag codes. Oxygen sensors can be a sticky job, they're screwed into exhaust and can literally weld themselves in place. Plus in most cases you need special wrench/socket to get around the sensor. (they can be a real pain)

http://www.obd-codes.com/

Posted on Jan 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My check engin light came on the codes came up as po133, p1000 what do i do to fix my car is a 1998 ford windstar?


A code P0133 may mean that one or more of the following has happened:
  • The oxygen sensor is faulty
  • The wiring to the sensor is broken / frayed
  • There is an exhaust leak
the problem is more than likely the front Bank 1 oxygen sensor. You will likely wind up replacing it but you should also consider these possible solutions:
  • Check and fix any exhaust leaks
  • Check for wiring problems (shorted, frayed wires)
  • Check the frequency and amplitude of the oxygen sensor (advanced)
  • Check for a deteriorating / contaminated oxygen sensor, replace if necessary
  • Check for inlet air leaks
  • Check the MAF sensor for proper operation
  • code p1000 refers to emission monitors not fully run and requires a couple of drive cycles from cold start to fully warmed drive cycle at different speeds.

Oct 10, 2014 | 1998 Ford Windstar

1 Answer

2003 jaguar s type code p1000 and c1165


the p1000 is a system readiness code meaning the car is checking itself..it means its not finished etc but once it has the code will change to p1111..meaning system check completed, the c1165 is a abs or wheel speed code, check the wheel where this code is originating

Apr 03, 2014 | 2003 Jaguar S-Type

1 Answer

1996 Oldsmobile LSS. Went to autozone and got code PO133. 'Fuel system running rich or lean- check other aacodes first.' and 'Oxygen sensor defective'; The guy said it probably isn't the oxygen sensor; as...


code P0133 is : o2 sensor circuit slow response (bank 1 sensor 1)
meaning;;;one heater on o2 sensor is not heating fast enough or no heat.
look for o2 sensor heater fuse first
and connector wiring for rust
if ok change o2 sensor

Oct 17, 2013 | 1996 Oldsmobile LSS

1 Answer

I've code p430 and p1000 and it said something about air gas controller


Catalitic converter mailfunction. Possible causes: - catalitic conv. mailfunction - o2 sensor mailfunction (ECU generates p430 from converter pre and post sensors data) - misfire; bad quality petrol, bad spark plugs, bad ignition coils (misfire means cat conv able to burn out without quick repair) - low fuel pressure: petrol filter needs replace, fuel pump needs replace - hole in exhaust system (sensors are ok, but measure wrong flow)

Nov 17, 2010 | 2003 Jaguar X-Type

1 Answer

2003 jaguar s type what does p 1000 code mean


If the Dianosis test Code P1000 is flagged after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles HAVE NOT BEEN COMPLETED. See http://www.bluejag.co.uk for further details on this

May 13, 2010 | 2004 Jaguar S Type

2 Answers

I have 2003 jaguar x type 2.5 and pluged a code reader and got result of "P0171" whats thats?


system too lean bank 1. check for vacuum leaks near the sid eof the engine which houses number 1 cylinder.

Dec 29, 2009 | 2003 Jaguar X-Type

1 Answer

Ihave detected an error code P1647 and P1111 on my jaguar x type. What does they mean or what could be the problem?


Code P1347 can be set for either a short to ground, short to power, high resistance or open circuit on Oxygen Sensor for bank 2, (HO2S21). Bank 2 is on your right when standing at the front of the engine facing the crank, and this sensor is the first in line; before the converters.
Code p1111
- Intake Air temperature (IAI) intermittent high voltage-low temperature condition.
Probable Cause:
1. Open circuit to IAI-Check connector
2. Failed IAI
3. Open Circuit Condition

Hope this helps

Dec 07, 2009 | 2002 Jaguar X-Type

3 Answers

What dose the code p1000 mean and p1645


P1645 EVAP Solenoid Output Circuit
P1000 Scan not complete. meaning it didnt finish scanning

Sep 14, 2009 | 2002 Jaguar X-Type

2 Answers

2002 windstar with po133 and po153 codes


do you have the meaning for the codes? if you do please descrive it, it will help a lot

May 30, 2008 | 2000 Ford Windstar

Not finding what you are looking for?
2003 Jaguar S-Type Logo

Related Topics:

823 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...