Question about 1995 Mercury Sable

1 Answer

Where is the thermostat for cooling system - 1995 Mercury Sable

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,400 Answers

Follow your top radiator hose to housing on top of engine, under that housing is your thermostat

Posted on Jan 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thermastat diagram install


Thermostat - 3.0L (2V) Removal and Installation
  1. Partially drain the engine cooling system. For additional information, refer to COOLING SYSTEM DRAINING, FILLING AND BLEEDING .
  2. Remove the three thermostat housing bolts. Fig. 25: Removing Thermostat Housing Bolts
    Courtesy of FORD MOTOR CO.

  3. Remove the thermostat O-ring seal.
  4. To install, reverse the removal procedure.
Thermostat - 3.0L (4V) Removal and Installation
  1. Raise and support vehicle. For additional information, refer to JACKING & HOISTING .
  2. Remove the front splash shield. For additional information, refer to FRONT END BODY PANELS .
  3. Drain the cooling system. For additional information, refer to COOLING SYSTEM DRAINING, FILLING AND BLEEDING .
  4. Remove the cooling tube bolt. Fig. 27: Removing Cooling Tube Bolt
    Courtesy of FORD MOTOR CO.

  5. Lower the vehicle.
  6. Remove the radiator upper cooling tube bolt. Fig. 28: Removing Radiator Upper Cooling Tube Bolt
    Courtesy of FORD MOTOR CO.

  7. Disconnect the upper radiator hose and engine vent hose. Fig. 29: Disconnecting Upper Radiator Hose And Engine Vent Hose
    Courtesy of FORD MOTOR CO.

  8. Remove the two bolts, and separate the radiator tube from the thermostat housing. Remove the thermostat. Fig. 30: Removing Bolts And Separating Radiator Tube From Thermostat Housing
    Courtesy of FORD MOTOR CO.

  9. To install, reverse the removal procedure.

Apr 22, 2012 | 2002 Ford Taurus

1 Answer

How do you change thermostat in 03 cobra where is the thermostat


4.6L Engine - replacing thermostat



CAUTION Never remove the radiator cap under any conditions while the engine is running, or while hot. Failure to heed this caution could result in cooling system damage or severe personal injury.
  1. Drain the engine cooling system until the coolant level is below the thermostat.
  2. Detach the lower radiator hose, the return hose and the degas bottle hose from the thermostat housing.
  3. Remove the two mounting bolts, then remove the thermostat housing.
  4. Remove the O-ring and thermostat from the housing. Discard the O-ring.

  5. archaeology_16.jpg
Figure - exploded view of thermostat and Housing - 4.6L engine

To install:

NOTE To prevent installing the thermostat with an incorrect orientation, the housing contains a positioning slot. Install the thermostat so that the bridge part protrudes into the housing, not into the intake manifold.
  1. Position the thermostat and a new O-ring on the housing, then install the housing.
  2. Install the two mounting bolts, and alternately tighten them to:
    1. 4.6L SOHC engines 15-22 ft. lbs. (20-30 Nm).
    2. 4.6L DOHC engines 89 inch lbs. (10 Nm).

  3. Connect the lower radiator hose, the return hose and the degas bottle hose to the housing.
  4. Fill the cooling system, then start the engine and check for leaks.
  5. If necessary, top off the cooling system overflow reservoir.

  1. Drain the engine cooling system.
  2. Remove the air cleaner outlet pipe.
  3. Remove the 2 thermostat housing bolts and separate the lower and upper thermostat housings.
    1. Discard the thermostat O-ring seal and remove the thermostat.


To install:

NOTE Lubricate the O-ring seal with clean engine coolant.
  1. Install a new thermostat with the smaller plate facing upward and the O-ring seal.
  2. Position the lower and upper thermostat housings together and install the 2 bolts. Tighten to 89 inch lbs. (10 Nm).
  3. Install the air cleaner outlet pipe.
  4. Fill and bleed the cooling system.

Feb 20, 2011 | 2003 Ford Mustang

2 Answers

Where is thermostat on my 2005 chevy classic


Thermostat Removal & Installation 2.2L Engine 2004-2005 To Remove:
  1. Drain the cooling system. chevy_cav_02-04_tstat.gif
  2. Remove the thermostat housing-to-water pump feed pipe bolts. chevy_cav_02-04_feedpipe.gif
  3. Remove the water pump feed pipe from the thermostat housing .
  4. Remove the thermostat from the housing.
To Install:
  1. Install the thermostat on the housing.
  2. Install the water pump feed pipe on the thermostat housing with the mounting bolts. Tighten 89 in-lb (10 Nm).
  3. Fill the cooling system.
2006-2007 To Remove:
  1. Drain the cooling system.
  2. Disconnect the radiator outlet hose from the surge tank and thermostat housing cover. Thermostat & cover gm-03-39-3601.gif
  3. Remove the mounting bolts and remove the thermostat housing cover.
  4. Remove the thermostat from the housing. Discard the O-ring.
To Install:
  1. Using a new O-ring, install the thermostat on the housing.
  2. Install the thermostat housing cover with the mounting bolts. Tighten 89 in-lb (10 Nm).
  3. Connect the radiator outlet hose to the surge tank and thermostat housing cover.
  4. Fill the cooling system.
3.5L Engine (LZ4) W/ Variable Valve Timing & 3.9L Engine To Remove:
  1. Drain the cooling system.
  2. Remove the air cleaner outlet duct.
  3. Disconnect the radiator outlet hose from the thermostat housing. Thermostat 3.9L gm-03-00-3054.gif
  4. Remove the mounting bolt/stud and remove the thermostat housing.
  5. Remove the thermostat from the engine.
  6. Clean the sealing surfaces.
To Install:
  1. Using a new gasket, install the thermostat on the engine.
  2. Install the thermostat housing with the mounting bolts. Tighten 89 in-lb (10 Nm).
  3. Connect the radiator outlet hose to the thermostat housing.
  4. Install the air cleaner outlet duct.
  5. Fill the cooling system.
  6. Check the cooling system for leaks.
3.5L Engine (LX9) W/O Variable Valve Timing To Remove:
  1. Drain the coolant.
  2. Disconnect the radiator hose from the thermostat housing. Thermostat 3.5L gm_mv_ven_tstat.gif
  3. Remove the mounting bolt/stud and remove the thermostat housing.
  4. Remove the housing gasket.
  5. Remove the thermostat.
  6. Clean the mating surfaces.
To Install:
  1. Install the thermostat on the engine.
  2. Install the thermostat housing and gasket with the mounting bolts. Tighten 18 ft-lb (25 Nm).
  3. Connect the radiator hose to the thermostat housing.
  4. Fill the cooling system.
  5. Check the cooling system for leaks.

Jan 29, 2011 | 2005 Chevrolet Malibu

1 Answer

Where to locate the thermostat on an 03 pontiac grand am?


Not sure which engine you have so please pick the appropriate engine:

2.2L Engine
  1. If equipped with an automatic transaxle, remove the exhaust manifold, as outlined in this section.
  2. Drain the cooling system.
  3. Remove the thermostat housing to water pump feed pipe bolts.
  4. Remove the thermostat housing to water pump feed pipe.

2112e0a.gif

Thermostat mounting-2.2L engine


3.1L Engines

  1. Disconnect the negative battery cable.
  2. Drain the cooling system to a level below the thermostat housing.
  3. Remove the air cleaner assembly.
  4. Disconnect the surge tank line from the thermostat housing.
  5. Remove thermostat housing-to-intake manifold attaching bolt and nut, then remove the housing.
  6. Remove the thermostat.

3.4L Engine
  1. Drain the cooling system.
  2. Remove the air cleaner.
  3. Remove exhaust crossover pipe.
  4. Disconnect the surge tank line fitting from the coolant outlet.
  5. Remove the thermostat housing to intake manifold bolts.
  6. Remove the thermostat housing outlet and thermostat
  7. Clean the mating surfaces.

Nov 01, 2010 | 2003 Pontiac Grand Am

1 Answer

Location of thermostat on 2002 olds alero 2.2


Thermostat Removal & Installation 2.2L Engine To Remove:
  1. Remove the exhaust manifold. If equipped with an automatic transmission.
  2. Drain the cooling system.
  3. Remove or disconnect the following: chevy_cav_02-04_tstat.gif

    • Thermostat housing to water pump feed pipe bolts. chevy_cav_02-04_feedpipe.gif

    • Thermostat housing to water pump feed pipe.
    • Thermostat.
To Install:
  1. Install or connect the following:
    • Thermostat.
    • Thermostat housing to water pump feed pipe.
    • Thermostat housing to water pump feed pipe bolt.
      1. Tighten bolt to 89 in lbs (10 Nm).
    • Exhaust manifold if equipped with an automatic transmission.
  2. Fill the cooling system.
2.4L Engine To Remove:
Thermostat assembly 2.4L 87953024.gif

  1. Drain the cooling system.
  2. Remove the exhaust manifold heat shield.
  3. Remove the coolant inlet housing mounting bolts through the exhaust manifold.
  4. Raise and safely support the vehicle.
  5. Remove the coolant inlet housing stud from the oil pan.
  6. Remove wheel and tire assembly.
  7. Remove the engine splash shield.
  8. Remove the mounting bolts from the transaxle-to-engine block support. Remove the support.
  9. Remove the coolant housing pipe.
  10. Remove the thermostat.
  11. Clean the mating surfaces.
To Install:
  1. Install the thermostat.
  2. Install the coolant housing pipe.
  3. Install and secure the transaxle support-to-engine block mounting bolts.
  4. Install the engine splash shield.
  5. Install the wheel and tire assembly.
  6. Install the coolant inlet housing stud to the oil pan.
    • Tighten to 19 ft lb (26 Nm).
  7. Lower the vehicle.
  8. Install the coolant inlet housing bolts through the exhaust manifold.
    • Tighten the coolant inlet housing bolts to 10 ft lb (14 Nm).
  9. Install the exhaust manifold heat shield.
  10. Fill the cooling system.
  11. Inspect the system for leaks.
3.4L Engine To Remove:
  1. Drain the cooling system.
  2. Remove the air cleaner.
  3. Remove exhaust crossover pipe.
  4. Disconnect the surge tank line fitting from the coolant outlet.
  5. Remove the thermostat housing to intake manifold bolts.
  6. Remove the thermostat housing outlet and thermostat.
To Install:
  1. Install the thermostat and housing outlet.
  2. Install the thermostat housing bolts.
    • Tighten the thermostat housing bolts to 18 ft lb (25 Nm).
  3. Install exhaust crossover pipe.
  4. Connect the surge tank line fitting to the coolant outlet.
    • Tighten the fittings to 15 ft lb (21 Nm).
  5. Install the air cleaner.
  6. Fill the cooling system.
  7. Inspect the system for leaks
prev.gif next.gif

Oct 14, 2010 | Oldsmobile Alero Cars & Trucks

2 Answers

Where is the thermostat on a 2.2l ohc engine?


Removal & Installation 2.2L VIN 4 To Remove:
  1. Drain the cooling system.
  2. Remove the lower radiator hose from thermostat housing.
  3. Remove the thermostat housing bolts and outlet.
  4. Remove the thermostat.
  5. Clean the mating surfaces.
To Install:
  1. Install the thermostat.
  2. Install the thermostat housing and bolts.
  3. Install the coolant housing bolts. Tighten bolts to 14 Nm (10 ft. lbs.).
  4. Install the lower radiator hose to thermostat housing.
  5. Fill the cooling system.
  6. Inspect for leaks.
2.2L VIN F To Remove:
  1. Remove the exhaust manifold. If equipped with an automatic transmission.
  2. Drain the cooling system.
  3. Remove or disconnect the following: chevy_cav_02-04_tstat.gif

    • Thermostat housing to water pump feed pipe bolts. chevy_cav_02-04_feedpipe.gif

    • Thermostat housing to water pump feed pipe.
    • Thermostat.
To Install:
  1. Install or connect the following:
    • Thermostat.
    • Thermostat housing to water pump feed pipe.
    • Thermostat housing to water pump feed pipe bolt. Tighten bolt to 10 Nm (18 in. lbs.).
    • Exhaust manifold. If equipped with an automatic transmission.
  2. Fill the cooling system.
2.4L VIN T To Remove:
  1. Drain the cooling system.
  2. Remove the exhaust manifold heat shield bolts and shield. cavman.gif

    cavtstat.gif

  3. Remove the coolant inlet housing bolts.
  4. Lift vehicle.
  5. Remove the coolant inlet housing stud from the oil pan.
  6. Remove the wheel.
  7. Remove the right engine splash shield.
  8. Remove the transaxle-to-engine block brace bolts and brace.
  9. Remove the radiator outlet pipe.
  10. Remove the thermostat.
  11. Clean the mating surfaces.
To Install:
  1. Clean the mating surfaces.
  2. Install the thermostat.
  3. Install the radiator outlet pipe.
  4. Install the transaxle-to-engine block brace and install bolts.
  5. Install the right engine splash shield.
  6. Install the wheel.
  7. Lower the vehicle.
  8. Install the exhaust manifold heat shield and bolt.
  9. Tighten the exhaust manifold heat shield bolts to 14 Nm (10 ft. lbs.).
  10. Fill the cooling system.
  11. Inspect the system for leaks.
prev.gif next.gif

Sep 09, 2010 | 2003 Pontiac Sunfire

1 Answer

Were is my thermostat in my 1997 eagle vision


REMOVAL & INSTALLATION
  1. Disconnect negative battery cable. CAUTION
    Do not remove the radiator pressure cap with the cooling system hot and under pressure. Serious burns from hot, pressurized coolant can result.
  2. Allow cooling system to cool completely. Place a pan under the radiator drain, located at the lower right side of the radiator. Open the valve to drain the cooling system to a level just below the thermostat. Do NOT drain the cooling system completely, unless the coolant is being changed. Close the valve.
  3. Loosen the radiator hose clamp from the upper radiator hose at the thermostat housing and if necessary disconnect the hose from the housing. Fig. 1: Loosen the radiator hose clamp from the upper radiator hose at the thermostat housing 88173p06.jpg
    Fig. 2: If necessary, separate the upper hose from the thermostat housing (it is not required) 88173p11.jpg

  4. Remove the thermostat bolts and housing. Fig. 3: Loosen the thermostat housing bolt with the proper size socket 88173p07.jpg

  5. Remove the thermostat and discard the gasket. Thoroughly clean both gasket sealing surfaces. Fig. 4: Separate the housing to access the thermostat 88173p08.jpg
    Fig. 5: Lift the thermostat out . . . 88173p09.jpg
    Fig. 6: . . . then clean the mating area 88173p10.jpg
    To install:
  6. Clean the thermostat housing bolts well. On any engine, bolts that thread into the water jacket are subject to rust and corrosion. A bolt with rust or debris in the threads can easily strip out the threads in an aluminum manifold requiring a time-consuming thread repair operation. Clean the bolts well and lightly lubricate before installation.
  7. Install the thermostat into the recess in the intake manifold. Place a new gasket, moistened with water, on the water inlet mating surface on the intake manifold.
  8. Install the thermostat housing over the gasket and thermostat and tighten the mounting bolts to 21 ft. lbs. (28 Nm) on the 3.3L engine and 105 inch lbs. (12 Nm) on the 3.5L engine.
  9. Connect the upper radiator hose to the thermostat housing and tighten the radiator hose clamp.
  10. Refill and bleed the cooling system.
prev.gif next.gif

Aug 19, 2010 | 1997 Eagle Vision

2 Answers

How do i change a thermostat on a 1996 mercury sable and whre is it located


Thermostat-follow the upper radiator thick hose to the thermostatic housing. Removal & Installation 3.0L (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions in the beginning of this section.
  2. Drain the engine cooling system into a suitable container.
  3. Remove the three thermostat housing bolts.
  4. Remove the thermostat O-ring seal.
  5. Inspect and clean the sealing surfaces.
To Install:
  1. Install thermostat and o-ring seal.
  2. Install thermostat housing bolts; torque to 9 lb-ft (12 Nm).
  3. Refill cooling system.
  4. Warm-up vehicle and check for leaks.
  5. Top off cooling system.
3.0L (4V) To Remove:
  1. Drain the engine cooling system.
  2. Disconnect the lower radiator hose from the water inlet adapter.
  3. Remove the bolts, the water outlet adapter and thermostat. Discard the O-ring seal.
To Install:
  1. Clean the sealing surfaces.
  2. Install the thermostat with a new gasket. Tighten the bolts to 89 in-lb (10 Nm).
  3. Refill the cooling system.
  4. Warm-up the vehicle and check for leaks.
  5. Top off the cooling system.
3.4L (SHO) To Remove:
  1. Drain the engine cooling system.
  2. Remove battery.
  3. Remove power distribution box.
  4. Remove battery tray.
  5. Disconnect upper radiator hose and place it out of the way.
  6. Disconnect the lower radiator hose from the water inlet connection.
  7. Remove the two mounting bolts and remove the water inlet connection.
  8. Remove the O-ring seal and thermostat from the water pump.
  9. Inspect O-ring for damage and replace if necessary.
To Install:
  1. If necessary, install a new O-ring on the inlet connection.
  2. Install the thermostat in the water pump and install the inlet housing. Tighten the bolts to 71-106 lb-in (8-12 Nm).
  3. Connect the lower radiator hose to the water inlet connection.
  4. Install the upper radiator hose.
  5. Install battery tray.
  6. Install the power distribution box.
  7. Install the battery.
  8. Refill the engine with coolant.
  9. Start the engine and allow the engine to warm up so that the water thermostat opens. Check for leaks.
  10. Stop the engine. Allow the engine to cool and top off degas bottle as required to maintain minimum cold fill level.
prev.gif next.gif

Aug 03, 2010 | 1996 Mercury Sable

1 Answer

Replace thermastat where is it and i need a easy fix solution


2.0L & 2.4L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect battery negative cable from remote negative terminal on shock tower and properly isolate to prevent accidental reconnection.
    CAUTION This operation must only be performed on a cold engine.
  3. Drain cooling system to the thermostat level or below.
  4. Remove or disconnect the following:
    Coolant recovery system hose Thermostat/engine outlet connector bolts Inlet hose and coolant elbow from thermostat housing
  5. Remove thermostat assembly and clean sealing surfaces.

    240b2a6.jpg
    Fig. Thermostat and housing-2.0L and 2.4L engines

To install:
  1. Place the new thermostat assembly into the engine outlet connector. Align air bleed with notch on the cylinder head.
  2. Install engine outlet connector onto cylinder head and tighten bolts to 110 inch lbs. (12.5 Nm)
  3. Connect the coolant recovery system hose.
  4. Fill cooling system.

  1. Drain cooling system to the thermostat level or below.
  2. Remove the Coolant Recovery System (CRS) hose and thermostat/engine outlet connector bolts.
  3. Remove the thermostat assembly, and clean sealing surfaces.

    969cc63.jpg
    Fig. Thermostat assembly-2.0L engine


    f7f1b3d.jpg
    Fig. Thermostat assembly-2.4L engine

To install:
  1. Place the new thermostat assembly into the engine outlet connector.
    1. Align air vent upward with notch on the cylinder head (2.0L engine).
    2. Make sure spring side of thermostat faces cylinder head.

  2. Install the engine outlet connector onto cylinder head and tighten bolts to 110 inch lbs. (12.5 Nm)
  3. Connect the Coolant Recovery System (CRS) hose.
  4. Fill cooling system.

2.4L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system to the thermostat level or below.
  3. Remove the Coolant Recovery System (CRS) hose and thermostat/engine outlet connector bolts.
  4. Remove the thermostat assembly, and clean sealing surfaces.

    a1e1b65.jpg
    Fig. Thermostat assembly-2.4L engine

To install:
  1. Place the new thermostat assembly into the engine outlet connector.
  2. Make sure the spring side of the thermostat faces the cylinder head.
  3. Install the engine outlet connector onto cylinder head and tighten bolts to 110 inch lbs. (12.5 Nm)
  4. Connect the CRS hose.
  5. Fill the cooling system to the proper level.

Hope help with this (remember rated this post).

Apr 15, 2010 | 2002 Chrysler Sebring

1 Answer

How to change the thermostat


Alero, Grand Am 1999-2005 Thermostat - Removal & Installation 2.2L Engine
  1. If equipped with an automatic transaxle, remove the exhaust manifold, as outlined in this section.
  2. Drain the cooling system.
  3. Remove the thermostat housing to water pump feed pipe bolts.
  4. Remove the thermostat housing to water pump feed pipe.

    d1db35e.jpg
    Fig. Thermostat mounting-2.2L engine
  5. Remove the thermostat.

To install:
  1. Install the thermostat.
  2. Install the thermostat housing to water pump feed pipe.
  3. Install the thermostat housing to water pump feed pipe bolt. Tighten the thermostat housing to water pump feed pipe bolt to 89 inch lbs. (10 Nm).
  4. If equipped with an automatic transaxle, install the exhaust manifold, as outlined in this section.
  5. Fill the cooling system.

3.1L Engines
  1. Disconnect the negative battery cable.
  2. Drain the cooling system to a level below the thermostat housing.
  3. Remove the air cleaner assembly.
  4. Disconnect the surge tank line from the thermostat housing.
  5. Remove thermostat housing-to-intake manifold attaching bolt and nut, then remove the housing.
  6. Remove the thermostat.

To install:
  1. Clean all gasket surfaces completely.
  2. Insert the thermostat in the intake manifold.
  3. Attach the thermostat housing to the intake manifold.
  4. Install the mounting bolt and nut. Tighten to 18 ft. lbs. (25 Nm).
  5. Install the air cleaner assembly.
  6. Connect the surge tank line to thermostat housing.
  7. Refill the cooling system.
  8. Connect the negative battery cable, remove the radiator cap, then start the engine. Allow the engine to run with radiator cap removed, until the upper radiator hose becomes hot (thermostat open). With the engine idling, add coolant to the radiator until the level is up to the bottom of the filler neck.
  9. Install the radiator cap, making sure the arrows line up with the overflow tube.

3.4L Engine
  1. Drain the cooling system.
  2. Remove the air cleaner.
  3. Remove exhaust crossover pipe.
  4. Disconnect the surge tank line fitting from the coolant outlet.
  5. Remove the thermostat housing to intake manifold bolts.
  6. Remove the thermostat housing outlet and thermostat
  7. Clean the mating surfaces.

To install:
  1. Install the thermostat and housing outlet.
  2. Install the thermostat housing bolts. Tighten the thermostat housing bolts to 18 ft. lbs. (25 Nm).
  3. Install exhaust crossover pipe.
  4. Connect the surge tank line fitting to the coolant outlet. Tighten the fittings to 15 ft. lbs. (21 Nm).
  5. Install the air cleaner.
  6. Fill the cooling system.
  7. Inspect the system for leaks.
Hope this help (remember comment and rated this).

Apr 04, 2010 | 1999 Oldsmobile Alero

Not finding what you are looking for?
1995 Mercury Sable Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...