Cars & Trucks Logo

Related Topics:

Posted on Jan 04, 2011
Answered by a Fixya Expert

Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

I have put the second transmittion in my car and its gone bad after about 6months

Answer This Question

1 Answer

Anonymous

Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

  • Master 3,400 Answers
  • Posted on Jan 04, 2011
Anonymous
Master
Level 3:

An expert who has achieved level 3 by getting 1000 points
Superstar:

An expert that got 20 achievements.
All-Star:

An expert that got 10 achievements.
MVP:

An expert that got 5 achievements.

Joined: Jan 02, 2011
Answers
3400
Questions
1
Helped
986213
Points
10767

Was the replacement transmission used by chance? Ford & Merc are not known for trans problems unless your doing alot of towing.

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I am trying to see my 2002 lincoln ls is equipped with remote keyless entry i bought car from private owner and i try buying a remote fob from dealer but didn't work what couldbethe problem
It has to be programmed .
Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.
  1. Turn the key from OFF to RUN four times within three seconds, ending in RUN. The locks will then lock and unlock, confirming program mode has been entered.
  1. Press any button on each remote transmitter to be programmed. The doors will lock and unlock to confirm that each remote transmitter has been programmed.
  1. If additonal remote transmitters are to be programmed, repeat Step 3 within 7.5 seconds or steps 2 and 3 if more than 7.5 seconds have elapsed.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
  1. NOTE: Failure to wait at least 20 seconds will cause programming failures.
    Wait at least 20 seconds after turning the key to OFF or after the last remote transmitter has been programmed to activate a remote transmitter for testing or verification.
Read full answer
Sep 27, 2015 • Lincoln Cars & Trucks
tip

Do it Yourself: Reprogramming the Remote Keyless Entry (RKE)
Normal 0 21 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Tabla normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Jeep Grand Cherokee Alarm System (1993-1998)

I would try reprogramming the Remote Keyless Entry (RKE) transmitters before looking for anything else. Make sure the batteries in the RKE transmitters are good and replace them if in doubt. Here's the procedure for programming the RKE transmitters.

Up to 4 Transmitter Identification Codes (TIC's) can be programmed into the receiver at any given time.

1. Open the driver's door of the vehicle. Leave it open through the programming procedure.
2. Move the mechanical door lock lever to the LOCK position.
3. Insert the ignition key and turn it to the RUN position.
4. Turn the ignition to the RUN position. Within 20 seconds, aim a transmitter at the receiver dome and press the lock button, for at least 5 seconds. Once the receiver accepts the programming code the driver's door will unlock.
5. Once the first transmitter has been programmed, additional transmitters (up to 4) may be programmed into the receiver. Within 20 seconds of the previous transmitter programming, move the mechanical door lock lever to the Lock position. Aim another transmitter at the receiver dome and press the LOCK button for at least 5 seconds. The door lock will cycle again.
6. To lock the programmed codes into the receiver, the ignition must be turned off and back on within 20 seconds after programming the last transmitter's code. At that time, all previous codes are erased from the module.

If the alarm still doesn't work correctly, you probably have a bad Alarm Module. If you wanna download this procedure, clic the image.

79482d7.gif

Enjoy Jeep.
Read full tip
on Sep 23, 2009 • 1993 Jeep Grand Cherokee
1helpful
2answers

The lock button on my key fobs will not lock the doors on 06 honda crv
CHeck to see if it is the right battery - Should be a CR1616 - previous year models, had a different battery.

Does the light come on on the key fob, when you push the button?

You may have to reprogram the remote - check the owners manual for instructions - if you can't find them...

Programming the Transmitter
NOTES:
• The system accepts up to three transmitters. The
transmitter codes are stored in a stacking-type
memory. If a fourth transmitter code is programmed,
the code for the first transmitter is erased.
• Entering the programming mode cancels all learned
transmitter codes, so none of the previously
programmed transmitters will work. You must
reprogram all of the transmitters once you are in the
programming mode.
• You must complete each step within 4 seconds of
the previous step to keep the system from exiting the
programming mode. Program the transmitters within
10 seconds.

1. Turn the ignition switch to ON (II).
2. Press the "Lock" or "Unlock" button on one of the
transmitters. (An unprogrammed transmitter can be
used for this step.)
3. Turn the ignition switch to LOCK (0).
4. Repeat steps 1, 2, and 3 two more times using the
same transmitter used in step 2.
5. Turn the ignition switch to ON (II).
6. Press the "Lock" or "Unlock" button on the same
transmitter. Make sure the power door locks cycle
to confirm that the system is in programming mode.
7. Within 10 seconds, press the "Lock" or "Unlock"
button on each transmitter. Make sure the power
door locks cycle after you press each transmitter
button to confirm that the system accepted the transmitter's code.
8. Turn the ignition switch to LOCK (0) to exit programming mode.


IF so, and more likely, the fuse on the car side of the remote, is probably gone.
Read full answer
Apr 25, 2012 • 2006 Honda CR-V
0helpful
1answer

I locked my keys in my 06 mercury mariner and i need to reset the code to my car, how can i reset the code?
You must have all remote entry transmitters (maximum of four) available before beginning this procedure. According with the Mariner Owners Manual check this procedure to reprogram the remote entry transmitters:

1. Ensure the vehicle is electronically unlocked.
2. Put the key in the ignition.
3. Turn the key from the 1 (LOCK) position to 3 (RUN).
4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK) position and 3 (RUN).
Note: The eighth turn must end in the 3 (RUN) position.
5. The doors will lock, then unlock, to confirm that the programming mode has been activated.
6. Within 20 seconds press any button on the remote entry transmitter.
Note: If more than 20 seconds have passed you will need to start the procedure over again.
7. The doors will lock, then unlock, to confirm that this remote entry transmitter has been programmed.
8. Repeat Step 6 to program each additional remote entry transmitter.
9. Turn the ignition to the 1 (LOCK) position after you have finished programming all of the remote entry transmitters.
10. The doors will lock, then unlock, to confirm that the programming mode has been exited.

Note: If all remote entry transmitters are not present during the programming procedure, the missing transmitters will not work with the vehicle following programming.

Hope helps.
Read full answer
Sep 07, 2011 • 2005 Mercury Mariner
0helpful
1answer

I have a 00 petrol ford focus but the fob key does not work anymore. I saw a programming explanation for a 02 diesel focus and I am wondering if there is such a solution for my car? Thank you.
OBTAIN ALL REMOTE TRANSMITTER. TRY THIS PROCEDURE.FASTEN SEAT BELTS AND CLOSE ALL DOORS.TURN IGNITION SWITCH FROM OFF TO ON 4 TIMES WITHIN 6 SECONDS.SWITCH IGNITION OFF,ACOUSTIC SIGNAL WILL SOUND AND SYSTEM WARNING LAMP WILL ILLUMINATE INDICATES CORRECT PROGRAMMING.WITH IN 10 SECONDS.PRESS AND HOLD ANY REMOTE TRANSMITTER BUTTON. WAIT FOR ACOUSTIC SIGNAL AND SYSTEM WARNING LAMP TO FLASH INDICATES CORRECT PROGRAMMING. TO PROGRAM ANOTHER REMOTE TRANSMITTER, REPEAT ABOVE PROCEDURE WITHIN 10 SECONDS.TO EXIT PROGRAMMING MODE,TURN IGNITION SWITCH TO CRANK OR WAIT 10 SECONDS. IF THIS PROCEDURE FAILS YOUR IGNITION KEY WORN OR IGNITION SWITCH RING COIL BAD.
Read full answer
Mar 15, 2011 • Ford Focus Cars & Trucks
0helpful
1answer

Transmittion leak from factory hole in rear bottom of transmittion, just before converter. never leaked before. any thoughts?
could be a weep hole for a seal that may have gone bad ?
Read full answer
Dec 26, 2010 • 1997 Jeep Wrangler
0helpful
1answer

1997 jeep will not start thinking its the anti theft lock but dont not how to reset the code ... does anyone know how
I would try reprogramming the Remote Keyless Entry (RKE) transmitters before looking for anything else. Make sure the batteries in the RKE transmitters are good and replace them if in doubt. Here's the procedure for programming the RKE transmitters.

Up to 4 Transmitter Identification Codes (TIC's) can be programmed into the receiver at any given time.

1. Open the driver's door of the vehicle. Leave it open through the programming procedure.
2. Move the mechanical door lock lever to the LOCK position.
3. Insert the ignition key and turn it to the RUN position.
4. Turn the ignition to the RUN position. Within 20 seconds, aim a transmitter at the receiver dome and press the lock button, for at least 5 seconds. Once the receiver accepts the programming code the driver's door will unlock.
5. Once the first transmitter has been programmed, additional transmitters (up to 4) may be programmed into the receiver. Within 20 seconds of the previous transmitter programming, move the mechanical door lock lever to the Lock position. Aim another transmitter at the receiver dome and press the LOCK button for at least 5 seconds. The door lock will cycle again.
6. To lock the programmed codes into the receiver, the ignition must be turned off and back on within 20 seconds after programming the last transmitter's code. At that time, all previous codes are erased from the module.

If the alarm still doesn't work correctly, you probably have a bad Alarm Module.
Click here also; http://www.scribd.com/doc/20110658/Keyless-Entry-System-Jeep-Grand-Cherokee
Read full answer
Oct 05, 2010 • 1997 Jeep Cherokee
0helpful
1answer

Reprogram 2005 dodge durango key fob
Daimier Chrysler North American Remote Keyless Entry Programming procedures

Program Method A (Customer Program Method)

1. Press (LOCK) button 5 times at 2 second Intervals to resynchronize transmitter, Attempt to function transmitter, If working as designed discontinue programming.

2. Turn ignition to run position, (Allow Ignition chimes to stop).

3. Using any original (working )transmitter, press the [UNLOCK] button for 4 to 10 seconds.

4. Within the specified 4 to l0 seconds, continue pressing the [UNLOCK] button and press the [PANIC] button for 1 second and release both buttons (AN/DN release either button first). A chime will sound to indicate that the transmitter programming mode has been entered (allow 3 seconds for chime to sound).

5. Press [LOCK] and [UNLOCK] buttons simultaneously for 1 second and release (a short chime will sound for AN/DN).

6. Press and release any button an the same transmitter and a chime will sound after successfully programming the transmitter (locks will cycle for AN/DN).

NOTE.- (FOR DR ONLY) A CHIME WILL NOT SOUND ON STEP #6 FOR THE FIRST TRANSMITTER PROGRAMMED, BUT WILL SOUND UPON PROGRAMMING THE SECOND TRANSMITTER.

7. Repeat steps 5 through 6 to program additional transmitters.

8. Turn ignition to OF:F position. Transmitter programming mode will discontinue after 60 seconds (30 seconds for AN/DN and RS). (All transmitter programming must be completed within time specified).


Read full answer
Nov 05, 2009 • 2005 Dodge Durango
3helpful
1answer

Keyless remote wont work
try to reprogram the remotes using these instructions..........
i assume for 02 explorer not th 05 frestyle listed (although similar procedure)
Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.
  1. Make sure that the anti-theft system is not armed or triggered and key code programming is not active.
  1. Open the door, then press the driver door lock control switch UNLOCK button.
  1. Turn the key from OFF to ON 8 times within 10 seconds, with the eighth turn ending in ON. If the program mode is sucessfully entered the doors will lock and unlock to confirm.
  1. Press any button on a remote transmitter, and the doors will lock and then unlock all doors to confirm that the remote transmitter is programmed. All remote transmitters must be programmed within 20 seconds of each other. Up to four remote transmitters can be programmed to the vehicles security module each time programming mode is entered.
  1. If the door locks do not respond for any remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Locks, Latches and Entry Systems — Late Build or Locks, Latches and Entry Systems — Early Build in this section.
  1. NOTE: Exiting is acknowledged by locking and unlocking the doors if at least one remote transmitter has been programmed.
    Exiting the programming mode is accomplished if one of the following has occurred:
    • The key transitions to OFF.
    • 20 seconds have passed since entering programming mode or since the last remote transmitter was programmed.
    • Four remote transmitters have been programmed.
Read full answer
Jun 02, 2009 • 2005 Ford Freestyle
3helpful
3answers

Keyless remote does not work after replacing batteries
I had the same problem and located the addendum to the owners manual. It's kind of overcomplicated it seems. Here is what it says:
1) Confirm all doors are closed and the key is out of the ignition.
2) Open the driver's door and put the key in the ignition within 10 seconds.
3) Remove the key within 10 seconds.
4) Push and release the driver's door switch 3 times within 20 seconds.
5) Insert the ingition key within 10 seconds.
6) remove the ignition key within 10 seconds
7) press and hold both "lock" and "unlock" on the transmitter for more than 5 seconds within 20 seconds of removing the key All doors will lock/unlock to confirm the process has been properly done.
8) Press "lock" or "unlock" on the transmitter within 5 seconds of completing step 7. All the doors will lock/unlock to confirm that the process was properly done.
At this point the transmitter has been properly programmed.

Of course, this didn't help me. My transmitter still does not work. I did confirm the procedure with a known good transmitter, so it is valid. If the lock/unlock does not happen in step 7, you more than likely have a bad transmitter.
Read full answer
Oct 12, 2008 • 2003 Suzuki Aerio
Not finding what you are looking for?

View Most Popular

1988 Grand Marquis

  • Cars & Trucks

Related Question

I am trying to see my 2002 lincoln ls is equipped with remote keyless entry i bought car from private owner and i try buying a remote fob from dealer but didn't work what couldbethe problem

  • Lincoln Cars & Trucks

Related Topics

61 views

Ask a Question

Usually answered in minutes!

Popular Questions

Why do my windshield wipers only work on high speed and when turning them off they stop where ever they happen to be, not going all the way down?

1995 Mercury Grand Marquis

Code 24 and 25 (blend door actuator)are showing up

2000 Mercury Grand Marquis

P1405, p1131, p0171, p1150, p1130,

Mercury Grand Marquis Cars & Trucks

How many quarts of oil does the 4.6 liter V8 take?

1993 Mercury Grand Marquis

Fuel gauge not working all the time.

1983 Mercury Grand Marquis

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Mercury Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...