Question about 1994 Ford Explorer Limited

1 Answer

Wont go into overdrive and reverse works, kinda

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Probably needs a new shift arm- wires get frayed. Dealer will do it for about $100. Takes about 30minutes

Posted on Jan 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2006 chevy cobalt wont run in drive it dies but will run good in reverse


On some old Buicks and Oldsmobiles the overdrive would stick on. A bandaid cure for them was to unplug the cable under the hood, but you no longer had overdrive. I heard that changing the transmission fluid would clear that up. There's no overdrive in Reverse.. placing the car in 1st or 2nd gear could bypass o/d also if they don't use the same gear set. Once up-to-speed, place the car in Drive. This only works if the reason the car dies is it can't accelerate in that high a gear at such a slow speed.

Oct 12, 2015 | 2006 Chevrolet Chevrolet Cobalt LS

1 Answer

Wont go in overdrive after it rained what is it


have the same problem. went kinda slow through a puddle cause someone in front of me was going slow. now wont shift into 4th and my check engine light came on. any ideas? is it the serpentine belt like the answer says above?

Jun 19, 2012 | 1997 Dodge Ram 1500 Club Cab

1 Answer

1996 honda accord wont shift into overdrive


For Automatic transmission problem,click the link below:----Overdrive light in the dash blinks? http://repairhelpcenter.blogspot.com/2012/01/overdrive-light-in-dash-blinks.html
--------- Automatic transmission troubleshooting:----

http://howtobyme.blogspot.com/2011/11/automatic-transmission-will-not-go-into.html

---------
Automatic transmission shift lever issues?-------

http://technoanswers.blogspot.com/2012/01/automatic-transmission-shift-lever-hard.html

-----------
AUTOMATIC TRANSMISSION FLUID LEVEL? --

http://schematicsdiagram.blogspot.com/2011/07/how-to-check-automatic-transmission.html

--------------

AUTOMATIC TRANSMISSION FLUID AND FILTER?

http://schematicsdiagram.blogspot.com/2011/07/how-to-change-automatic-transmission.html

-----------
Transmission fault light on car dash?

http://schematicsdiagram.blogspot.com/2011/12/transmission-fault-light-on-car-dash.html

--------
Transmission shifting problem?

http://schematicsdiagram.blogspot.com/2012/01/transmission-shifting-problem-on-toyota.html

--------
Transmission Slips out of 2nd gear?

http://repairhelpcenter.blogspot.in/2012/02/transmission-slips-out-of-2nd-gear.html

-----------
OD light flashing and transmission fluid leaking?

http://repairhelpcenter.blogspot.in/2012/02/od-light-flashing-and-transmission.html

----------
Why Transmission fluid leaks near radiator?

http://repairhelpcenter.blogspot.in/2012/02/transmission-fluid-leaks-near-radiator.html

----------
Transmission fluid leaking?

http://technoanswers.blogspot.in/2012/02/ford-windstar-transmission-fluid.html

-------------
****** wont go in reverse?

http://technoanswers.blogspot.in/2012/02/dodge-neon-wont-go-in-reverse.html

-------------
Automatic transmission will not go into reverse?

http://technoanswers.blogspot.in/2012/02/dodge-automatic-transmission-will-not.html

----------
Transmission is making buzzing noise?

http://technoanswers.blogspot.in/2012/02/transmission-is-making-buzzing-noise.html

-----------

This will help.

Thanks.

Mar 04, 2012 | 1996 Honda Accord

2 Answers

Transmission makes whining noise in park and neutral. Wont shift into overdrive. And reverse wont work.


Time for a rebuild or a new tranny, this one won't last much longer, sounds like there are bearings and clutches failing or failed already.

May 04, 2011 | 1999 Chevrolet K1500

1 Answer

First of all i have to grandchildren iam raising iam brook and my truck wont go in to overdrive all the time i need to know how to put overdrive syinoyed and tourkconverter syinoyed in iam kinda mach...


Ok first of all there is no solenoid deticated to overdrive.You have two shift solenoids and a combination of the being on/off gives you the different gears.My first question would be do you have any codes stored?

Mar 28, 2011 | 2002 Chevrolet Silverado 1500HD

2 Answers

I have a 2002 ford focus and the car will not move in reverse. It moves forward in drive only, but won't kick into overdrive. Any ideas


sounds like its internal, like the reverse band, that applies the overdrive, or the clutches that apply when in overdrive, either way the reverse band and overdrive clutches work hand in hand, for overdrive and reverse... id say you need a rebuild or a junk yard unit.... :( sorry for the bad news.

Nov 29, 2010 | 2001 Ford Focus

1 Answer

I have a 2000 Expedition 4.6L Triton. I've had truck about 7 years and love it. I have had all the transmission issues this truck can have...(I thought) until now this: SYMPTOM Transmission drives well in...


4R100 or 4R70W?

Geartrain
Power is transmitted from the torque converter to the geartrain components through the input shaft and forward clutch cylinder.
  • By holding or driving certain members of the gearset, four forward ratios and one reverse ratio are obtained and transmitted to the output shaft. The ratios are as follows:


GEAR RATIO 1ST 2.71 to 1 2ND 1.54 to 1 3RD 1.00 to 1 4TH 0.71 to 1 REVERSE 2.18 to 1
Input Shaft
The input shaft is supported by two bushings in the stator support. End positioning of the input shaft is controlled by the splines in the converter turbine and the overdrive planet assembly.
Output Shaft
The output shaft is supported by two bushings in the case and by the slip-yoke and bushing in the extension housing. End positioning is controlled by the parking pawl gear and snap ring or shoulder and by the reverse ring gear hub and snap ring.
Overdrive System
The overdrive planetary system consists of the overdrive planet assembly, overdrive sun gear, overdrive ring gear, coast clutch cylinder, overdrive one-way clutch assembly and the center shaft, as shown in the following illustration. The overdrive planet assembly is splined to the input shaft. The overdrive sun gear is centered by a bushing on the input shaft and held in place laterally by needle bearings on the reactor support and the overdrive planet assembly. The overdrive sun gear is splined to the coast clutch cylinder, which in turn is splined to the overdrive one-way clutch inner race.
The outer race of the one-way clutch is splined to the overdrive ring gear, which is splined to the center shaft. The center shaft is centered by the forward planetary assembly and is laterally held by needle bearings on the center support and the overdrive planet assembly. The center shaft is splined into the forward clutch cylinder.
Two friction clutches are assembled in the overdrive planet assembly. The coast clutch is splined between the coast clutch cylinder and the overdrive ring gear. The coast clutch is activated to perform engine braking in MANUAL 1, MANUAL 2 and third gear with the transmission control switch engaged.
The overdrive clutch is splined between the case and the coast clutch cylinder. The overdrive clutch holds the coast clutch cylinder and, in turn, the overdrive sun gear, to permit the planet assembly to overdrive the ring gear.
--------------------------------------------------------------------------------------------
Forward Drive System
The forward drive system consists of the forward clutch cylinder, intermediate brake drum, intermediate one-way clutch, input shell, forward ring gear, forward ring gear hub, forward/reverse sun gear and the forward planetary carrier and forward planetary gears.
The forward clutch cylinder is splined on the center shaft. The forward ring gear is piloted on the forward ring gear hub. Thrust bearings on the forward planet assembly and forward clutch cylinder hold the forward ring gear hub in place.
The intermediate brake drum is radially supported by bushings on the center support and is laterally controlled by thrust washers on the forward clutch cylinder and center support. The intermediate brake drum has the inner race of the intermediate one-way clutch press-fitted on its pilot. The intermediate one-way clutch's outer race is splined to the intermediate friction clutch, which is splined to the case. The intermediate brake drum has lugs that are slotted into the input shell to form a mechanical connection. The input shell is splined into the forward/reverse sun gear. The forward/reverse sun gear is common to two planetary gearsets. The forward planet is splined to the output shaft and is laterally positioned by needle bearings on the sun gear and on the forward clutch cylinder, as shown in the following illustration.
Two friction clutch assemblies, the direct clutch and the forward clutch, are shown with the forward planetary assembly. The direct clutch assembly splines the forward clutch cylinder to the intermediate brake drum. The forward clutch assembly splines the forward clutch cylinder to the forward ring gear. The forward clutch is activated during all forward gears. While in third or fourth gear, both the direct and forward clutches are applied to hold the forward planetary assembly and enable it to act as a solid shaft.
In second gear, the intermediate clutch assembly holds the forward/reverse sun gears. It is applied, along with the intermediate one-way clutch, to hold the intermediate brake drum, input shell and forward/reverse sun gear. In higher gears, the one-way clutch overruns.
----------------------------------
Low and Reverse Drive System
The reverse planetary assembly consists of the reverse planetary carrier, reverse planet gears, the reverse ring gear, the reverse ring gear hub, the reverse clutch hub and the low-reverse one-way clutch assembly.
The reverse ring gear hub is splined to the output shaft and to the reverse ring gear. The reverse ring gear hub is laterally held by a needle bearing on the inner race of the low-reverse one-way clutch and a snap ring on the output shaft. The reverse planet assembly is splined to the low-reverse clutch hub. The low-reverse clutch hub is connected by the reverse clutch to the case. The inner race of the one-way clutch is bolted to the case.
The reverse clutch assembly is activated in REVERSE gear and in MANUAL 1. The reverse clutch bypasses the reverse one-way clutch during coast and MANUAL 1. The reverse clutch holds the reverse planet assembly in REVERSE gear to enable the sun gear to drive the reverse ring gear in the opposite direction.
-------------
Apply Components
The following information describes the operation of the three 4R100 one-way clutches.
One-Way Clutch—Overdrive
The overdrive one-way clutch, shown in the following illustration, transmits engine torque from the overdrive sun gear to the overdrive ring gear in first, second and third gear range. The overdrive one-way clutch transmits power when the sprags are engaged between the inner and outer races. The inner race is splined to the coast clutch cylinder, which in turn is splined to the overdrive sun gear. The outer race is splined to the overdrive ring gear.
The overdrive one-way clutch engages whenever the overdrive planetary system attempts to drive the overdrive sun gear clockwise when the overdrive ring gear has a counterclockwise torque from the vehicle. When torqued counterclockwise, the overdrive one-way clutch engages and acts as a wedge to lock the sun gear and the ring gear together. During coast, the overdrive one-way clutch enables the ring gear to overrun or spin at a faster rate than the sun gear.
The overdrive one-way clutch overruns when in overdrive (fourth gear). In overdrive, the coast clutch cylinder is held by the overdrive one-way clutch, which in turn holds the overdrive sun gear. This causes the overdrive planet assembly to walk around the sun gear and overdrive the overdrive ring gear. The inner race of the overdrive one-way clutch is thus held stationary while the outer race is allowed to overrun clockwise.
--------------------------------------------

Nov 10, 2009 | 2000 Ford Expedition

1 Answer

I HAVE A 2001 EXPIDITION WHILE YOU ARE DRIVING THE TRANSMISSION WONT FIND OVERDRIVE IT ACT LIKE IT IS IN NEUTRAL BUT WHEN YOU TURN OVERDRIVE OFF RUNS FINE AND THE TRUCK WONT GO IN REVERSE WITH OVERDRIVE ON...


It sounds like your tranny is nearing the end of its life.Have you ever had it flushed?If it has high miles on it i wouldnt do it.The fact that it wont go into reverse sounds like it is time to replace/rebuild the unit.

Mar 29, 2009 | 2001 Ford Expedition

2 Answers

Transmission wont get into overdrive or reverse.


sounds like a 700r4 tranny thats usually what happens when they decide to quit you loose overdrive and reverse. About 900 to 1000$ to rebuild.

Dec 14, 2008 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
1994 Ford Explorer Limited Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...