Question about 1996 GMC Yukon

1 Answer

I have a 1996 GMC Yuckon and it wont start, i have to spay starter fliud in it already put in a fuel pressure regulater and fuel pump is making noise.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Check rubber hose in tank going from pump to sending unit / also if there isnt injector pulse could be cam sensor in distributor

Posted on Jan 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is crankshaft position sensor located 1996 gmc sierra 1500


The crankshaft position sensor is located on the right-side (passenger side) of the engine. At the rear of the engine, behind the starter. You need to remove the starter to remove the crank sensor. Remember to disconnect the battery first. The starter can short against the cross member.

Mar 03, 2014 | Cars & Trucks

2 Answers

2008 ssangyong sports had new camshaft replaced but wont start


Did you test the fuel pump relay and fuel pump pressure?

Jan 20, 2014 | 2007 SsangYong Actyon 4x4

1 Answer

Before changing starter fuel pump was working fine now that new started has been put on fuel pump wont kick on what could be the problem


check to make sure oil pressure switch wires did not get knock off for it is right by the starter and it is a saftey switch for fuel pump also

Mar 19, 2011 | 1996 Chevrolet Cavalier

1 Answer

Engine has trouble firing. It turns over several times before finally firing or killing my battery. Already replaced the battery and alternator, starter seems ok. What next? Engine is 2.2L 4 cyl...


gmc put two sistems to the fuel pump 1 fuel pump relay 2 oil pressure sensor if the relay is bad it takes longer to start until oil pressure is buildup if the oil is too old or too tick or the oil pump is old not building enogh pressure all that together is very bad but depend how many miles on

Dec 16, 2010 | 1996 Chevrolet S-10 Pickup

1 Answer

1996 gmc sonoma, wont start, if i prime it it will start then it dies, already replace the fuel filter and fuel relay...help


Have you hooked up a preesure gauge, if youre priming it by turning the key a few times i would say you have a fuel pump thats low on pressure and probably should be replaced.

Aug 04, 2010 | 1996 GMC Sonoma

1 Answer

My 1996 crown vic will not start motos turns over and trys to start but wont I have replaced intake manifold spark pulgs. motor has spark


basics,,,air,,fuel,,spark,,compression,,timing,,,pull a few plugs,,smell them for fuel,,if dry,,,take snorkel off throttle body,, open throttle body or flap half way,,spay a little starting fluid or injector spay into throttle put the snorkel back on see if motor fires up,,if so then ck fuel delivery & pressure,,,,hope it helped

May 28, 2010 | 1996 Ford Crown Victoria

1 Answer

1996 gmc jimmy will turn over but wont crank un less you put eather in it and when it starts up it runs normal but wont start with out eahter


Hmmm so the old boy wont start without some starting fluid eh?
I Love GM vehicles but I am not there. Here is a checklist of what I would ask myself were I there and able to test.
1. are the batteries and starter in good condition so it cranks at the speed it should without killing the voltage necessary to fire the injectors?
2. what is the fuel pressure to the injectors?
3. when was the last tuneup?

Id lean towards the fuel pressure because by this year it started being more critical and the pumps were in the tank and they would start going bad and causing all sorts of hard to troubleshoot problems. These days I pretty much start troubleshooting with checking fuel pressure.
Fuel pressure with the key on engine off should be 60-66. anything less then that could be a problem.

Apr 12, 2010 | 1996 GMC Suburban

3 Answers

Gmc sub wont start 1996


It sounds like the fuel pump. You may still be able to hear the pump, but it needs to produce a lot of pressure. If it is weak it won't do the job.

Jul 01, 2009 | 1996 GMC Suburban

Not finding what you are looking for?
1996 GMC Yukon Logo

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...