Question about 1995 Nissan Sentra

1 Answer

How do I remove the belt so I can remove the Water Pump?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 270 Answers

If you are referring to serpentine belt, Thisis how to do it. Lift the hood and prop it open. Find thelock nut on the serpentine belt and use a wrench to loosen it. Turn the adjustment bolt counterclockwiseto remove the serpentine belt. This bolt is located under the water pump hose.Remember how you remove the belt so that you can reroute the new beltcorrectly. Install the new serpentine belt by securingit on the pulleys in the same route as the old belt. Check the belt routing onthe underside of the hood to make sure you get it right. Create tension in the back of the belt byturning the adjustment bolt clockwise. Check that the belt is on each pulleyproperly. The belt should be centered on each pulley, not on the edge.Tightenthe lock nut to secure the serpentine belt in place.

Posted on Jan 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the water pump on a 2006 equinox ls


  1. Drain the cooling system until the coolant is below the level of the water pump.
  2. Loosen the water pump pulley bolts.
  3. Rotate the drive belt tensioner to release the tension on the drive belt.
  4. Remove the drive belt from the right idler pulley.
  5. Carefully release the drive belt tensioner spring tension.
  6. Remove the water pump pulley bolts.
  7. Remove the water pump pulley.
  8. Remove the water pump bolts.
  9. Remove the water pump.
  10. Remove the water pump gasket.
  11. Clean the water pump mating surfaces.

To install:

Fig. Remove the mounting bolts (3) to remove the water pump (1) and gasket (2).
  1. Install the water pump gasket (2).
  2. Install the water pump (1).
  3. Install the water pump bolts (3). Tighten the bolts to 10 Nm (89 inch lbs.).
  4. Install the water pump pulley. Loosely install the pulley bolts.
  5. Insure the drive belt is properly centered on all the pulleys except the right idler puller.
  6. Rotate the drive belt tensioner away from the drive belt.
  7. Install the drive belt to the right idler pulley.
  8. Release the tensioner allowing the drive belt tensioner to come in contact with the drive belt.
  9. Inspect the drive belt to insure the belt is properly centered on all the pulleys.
  10. Tighten the water pump pulley bolts. Tighten the bolts to 25 Nm (18 ft. lbs.).
  11. Fill the cooling system.
  12. Inspect the cooling system for leaks.


10177766-xy2b1ep4azxtiqpd5mnkcpdl-4-0.jpg

10177766-xy2b1ep4azxtiqpd5mnkcpdl-4-1.gif

Aug 21, 2011 | 2006 Chevrolet Equinox

2 Answers

I have no clue on how to replace water pump on a 1995 chrysler cirrus 2.5L. I have to do this myself I dont have the money for a garage.


This is found on the autozone.com website.

2.5L Engine
See Figures 3 through 7
  1. Disconnect the negative battery cable.
  2. Place a large drain pan under the radiator drain plug. Drain and properly contain the engine coolant.

This procedure requires removing the engine timing belt and the auto tensioner. To help assure proper alignment at assembly, it may be helpful to set the engine at TDC on No. 1 compression stroke. This should align all timing marks on the crankshaft sprocket and both camshaft sprockets.
  1. Remove the accessory drive belts and crankshaft damper.
  2. Remove the right engine mount. This requires safely supporting the engine with a floor jack and wood block so the mount can be removed.
  3. Remove the timing belt covers.
  4. Remove the timing belt and tensioner.



0900c152800896a7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Remove the water pump mounting bolts


0900c152800896a8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: Pull the water pump assembly off of the engine and inlet pipe


0900c152800896a9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Open the water pump housing and examine for cracks or damage


0900c152800896aa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: Replace the water pump housing gasket using a scraper tool


0900c152800896ab.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Always keep the water pump's mounting bolts lined up with their correct mounting holes

  1. Remove the water pump mounting bolts.
  2. Separate the water pump from the water inlet pipe and remove the pump.

To install:
  1. Thoroughly clean all sealing surfaces. Inspect the pump for damage or cracks, signs of coolant leakage at the vent, and excessive looseness or rough turning bearings. Any problems require a new pump.
  2. Install a new O-ring on the water inlet pipe. Wet the O-ring with water to make installation easier. DO NOT use oil or grease on the O-ring.
  3. Install a new gasket on the water pump and fit the pump inlet opening over the water pipe. Press the assembly together to force the pipe into the water pump.
  4. Install the water pump-to-engine bolts and tighten to 20 ft. lbs. (27 Nm).
  5. Install the timing belt and timing belt tensioner. Set the timing belt tension.
  6. Install the timing belt covers. Install the right engine mount. Remove the floor jack and engine block from underneath the engine.
  7. Install the crankshaft damper.
  8. Install the accessory drive belts and set to the proper tension.
  9. Connect the negative battery cable.
  10. Fill and bleed the engine cooling system.
  11. Start the engine and verify proper operation, with no leaks

Aug 20, 2011 | 1995 Chrysler Cirrus

1 Answer

How long does it take to replace a water pump on Pontiac Aztec?


It takes near to 1.5 hours to replace the water pump on Pontiac Aztec. The procedure to replace the water pump is as follows:--- Water Pump Replacement ---------
Removal Procedure :
techmecho.gif
  1. Drain the cooling system until the coolant is below the level of the water pump.
  2. Remove the drive belt guard.
  3. Loosen the water pump pulley bolts.
  4. Remove the drive belt.
techmecho_0.gif
  1. Remove the water pump pulley bolts.
  2. Remove the water pump pulley.
techmecho_1.gif
  1. Remove the water pump bolts.
  2. Remove the water pump.
  3. Remove the water pump gasket.
  4. Clean the water pump mating surfaces
Installation Procedure
  1. Install the water pump gasket.
  2. Install the water pump. Notice: Refer to Fastener Notice in Service Precautions.
  3. Install the water pump bolts.
    • Tighten the bolts to 10 Nm (89 inch lbs.) .
techmecho_2.gif
  1. Install the water pump pulley. Loosely install the mounting bolts.
  2. Install the drive belt.
  3. Install the water pump pulley bolts.
    • Tighten the bolts to 25 Nm (18 inch lbs.) .
techmecho_3.gif
  1. Install the drive belt guard.
  2. Fill the cooling system.
  3. Inspect the cooling system for leaks.
  4. That's it.

Nov 18, 2010 | 2001 Pontiac Aztek

1 Answer

How to take off the water punp


1. Drain the cooling system until the coolant is below the level of the water pump. 2. Remove the drive belt guard. 3. Loosen the water pump pulley bolts. 4. Remove the drive belt. 5. Remove the water pump pulley bolts. 6. Remove the water pump pulley. 7. Remove the water pump bolts. 8. Remove the water pump. 9. Remove the water pump gasket. 10. Clean the water pump mating surfaces. Installation Procedure 1. Install the water pump gasket. 2. Install the water pump Notice: Refer to Fastener Notice in Service Precautions. 3. Install the water pump bolts. Tighten the bolts to 10 Nm (89 inch lbs.). 4. Install the water pump pulley. 5. Install the water pump pulley bolts. 6. Install the drive belt. Tighten the water pump pulley bolts to 25 Nm (18 inch lbs.). 7. Install the drive belt guard. 8. Fill the cooling system

Aug 13, 2010 | 2002 Buick LeSabre

1 Answer

Remove and replace the water pump buick rendezvou 2003 cost and do it yourself instructions . can i do it myself concerned with loosening the serpentine belt and needing special tools?


1. Drain the cooling system until the coolant is below the level of the water pump. 2. Remove the drive belt guard. 3. Loosen the water pump pulley bolts. 4. Remove the drive belt. 5. Remove the water pump pulley bolts. 6. Remove the water pump pulley. 7. Remove the water pump bolts. 8. Remove the water pump. 9. Remove the water pump gasket. 10. Clean the water pump mating surfaces. Installation Procedure 1. Install the water pump gasket. 2. Install the water pump Notice: Refer to Fastener Notice in Service Precautions. 3. Install the water pump bolts. Tighten the bolts to 10 Nm (89 inch lbs.). 4. Install the water pump pulley. 5. Install the water pump pulley bolts. 6. Install the drive belt. Tighten the water pump pulley bolts to 25 Nm (18 inch lbs.). 7. Install the drive belt guard. 8. Fill the cooling system
Visit my Blog here

Jul 21, 2010 | 2002 Buick Rendezvous

1 Answer

How do I change a water pump on a 2004 kia sorento?


Kia Sorento 2003-05
Water Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

  9. dc45c19.jpg

    Fig. Water pump and timing belt assembly-exploded view

To install:

1016213.jpg

Fig. Water pump bolt locations
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. Refill the coolant.
  7. Run the engine and check for leaks.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

To install:


e9be8c3.jpg

Fig. Water pump bolt locations

596080e.jpg

Fig. Water pump O-ring installation
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. To adjust the drive belt tension, hang the belt on the pulley of the tensioner and install the tensioner.
    NOTE If the tensioner is already installed, loosen its mounting bolts to allow belt installation
  7. Install the drive belt.
  8. Adjust the belt tension to specification by turning the adjusting bolt clockwise or counterclockwise.
  9. Air conditioning belt tension should be 0.28-0.039 inch. Alternator belt tension should be 0.39-0.051 inch. Power steering belt tension should be 0.31-0.051 inch.
  10. Torque the tensioner assembly bolt to 33-36 ft. lbs. (45-50 Nm).
  11. Refill the coolant.
  12. Run the engine and check for leaks.

TY for using Fixya; remember comment and rated this.

Apr 01, 2010 | 2004 Kia Sorento

3 Answers

91 carolla water pump


No. You don't have to remove the timing belt to change the water pump. Check out the autozone.com website and register. It doesn't cost anything and you will have access to a repair manual for the vehicle. The steps for replacing the water pump can be found there. ( I checked) Hope this helps and best wishes.

Aug 18, 2009 | 1991 Toyota Corolla

1 Answer

How to change engine belts on a jaguar x-type 2003 3.0


To Remove BELTS : Drive Belt :
Disconnect battery ground cable
Remove wheel and tire
Detach accessory drive belt
detention drive belt
detach accessory drive belt
Remove accessory drive belt
slacken the tensioner
remove accessory belt drive

Install in reverse order
WATER PUMP BELT : Remove battery tray
Remove water pump belt
De-tension water pump belt
Remove water pump belt

Installation in reverse
Hope this is helpfull

Jul 11, 2009 | 2003 Jaguar X-Type

1 Answer

How do you replace a water pump in an aztec?


Notes Water Pump Replacement

Removal Procedure
3e77de9.gif

  1. Drain the cooling system until the coolant is below the level of the water pump.
  2. Remove the drive belt guard.
  3. Loosen the water pump pulley bolts.
  4. Remove the drive belt.


c7273fb.gif
  1. Remove the water pump pulley bolts.
  2. Remove the water pump pulley.
c102468.gif
  1. Remove the water pump bolts.
  2. Remove the water pump.
  3. Remove the water pump gasket.
  4. Clean the water pump mating surfaces
Installation Procedure
  1. Install the water pump gasket.
  2. Install the water pump. Notice: Refer to Fastener Notice in Service Precautions.
  3. Install the water pump bolts.
    • Tighten the bolts to 10 Nm (89 inch lbs.) .
f16e1fd.gif
  1. Install the water pump pulley. Loosely install the mounting bolts.
  2. Install the drive belt.
  3. Install the water pump pulley bolts.
    • Tighten the bolts to 25 Nm (18 inch lbs.) .
  • 258f600.gif
  1. Install the drive belt guard.
  2. Fill the cooling system.
  3. Inspect the cooling system for leaks

Jun 17, 2009 | 2001 Pontiac Aztek

1 Answer

How Do i replace Water Pump on 98 Chevy Metro


  1. Remove the negative battery cable.
  2. Drain the engine cooling system.
  3. Remove the air cleaner assembly.
  4. Remove the A/C compressor suction pipe bracket (if equipped).
  5. Loosen four water pump pulley bolts. Do not remove the bolts.
  6. Raise the vehicle. Support the vehicle. Remove the right lower splash shield.
  7. Remove the right lower splash shield.
  8. Remove the A/C compressor drive belt (if so equipped) by releasing the tensioner pulley and removing the belt from the crankshaft and compressor pulleys.
  9. Loosen the generator adjusting bolt (1), pivot the generator and remove the water pump/generator drive belt.
  10. Remove the crankshaft pulley.
  11. Remove the water pump pulley (four bolts).
  12. Remove the timing belt.
  13. Remove the oil level indicator (dipstick) guide tube.
  14. Remove the upper generator adjusting bracket from the water pump (one bolt).

    1. Remove the rubber seals from the water pump.
    2. Remove the water pump mounting bolts and nuts.
    3. Remove the water pump and gasket from the vehicle.
    4. Clean the water pump and the gasket mating surfaces.
    5. Install the water pump.
    6. Secure the water pump with mounting nuts and bolts. Tighten Tighten the water pump mounting nuts and bolts to 13 Nm (115 ft. lbs.).
    7. Install new rubber seals (1) to the water pump (2).
    8. Install the upper generator adjusting bracket to the water pump (one bolt).
        • Tighten the upper generator mounting bracket bolt to 23 Nm (17 ft. lbs.).
      1. Install the oil level indicator (dipstick) guide tube.
      2. Install the timing belt.
      3. Install the water pump pulley.
      4. Finger-tighten the four bolts.
      5. Install the crankshaft pulley.
      6. Install the water pump/generator drive belt to the crankshaft, water pump and generator pulleys.

Nov 20, 2008 | 1998 Chevrolet Metro

Not finding what you are looking for?
1995 Nissan Sentra Logo

278 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...