Question about 1991 Chrysler New Yorker

1 Answer

Replace oil pressure sensor - 1991 Chrysler New Yorker

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,400 Answers

It's easy fix if it's V8 it's in back by distributor, unplug cable, unscrew sender from engine, screw new one in and connect wire. If it's six cylinder it's next to distributor on side of engine.

Posted on Jan 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2007 Buick oil light comes on and off at random. Recently changed oil. GTX extended milage. .5w30. Oil level good. Any ideas


Oil pressure sensor, or most likely, oil level sensor, either sensors, wires, or connections.

Sep 04, 2016 | Buick Cars & Trucks

1 Answer

Where is oil sending unit located?


You're vehicle has two sensors for the oil,an oil pressure sensor switch & oil pressure sensor.If oil pressure gets below 6psi,the oil pressure sensor switch will turn a dash light on to let you know the pressure is at a dangerously low amount.So if you've got a dash light on,the pressure sensor switch needs to be replaced.Its located to the right of the oil filter housing,on a 2.0 liter.Its located to the left of the oil filter housing,on the 3.0 liter.
If your oil pressure gauge is reading inaccurately,you need to replace the oil pressure sensor instead.Its located near the ac compressor.

Oct 15, 2015 | 2003 Ford Escape

1 Answer

Replaced oil sensor light still comes on


MAY---May-be you really have low oil pressure.. The way this sensor works is when you turn off the engine it closes to ground.. and when you start the engine.. the oil pressure opens it and the light goes out.. SO.. if the wire going to it is grounded out somewhere between the sensor and the dash board the light will stay on.. 3 choices.. 1. bad sensor (even though you replaced it) 2. wire is shorted to ground.. remove wire from sensor while engine is running.. light should go out. 3. you actually have really low oil presure. next.. after you have exuasted #1-2. you can remove sensor and install a real oil pressure guage and see what the pressure really is.. If you have very low or no oil pressure..1. Check oil level.(probably should have done this first) 2.pull oil pan and replace oil pump.. while you are there check a main bearing and a rod bearing for wear.. worn out bearings will cause low oil pressure. If you have good oil pressure install the pressure guage permanetly and forget about light.

May 25, 2014 | Buick LeSabre Cars & Trucks

1 Answer

2003 Dodge Neon Check Oil light wont go off. Car has oil-full, and just put in new Sensor.


Do you mean the oil level sensor was replaced, or do you mean the oil pressure sending unit was replaced?
If it was the oil pressure sensor was replaced, then I would look into an oil pump going bad, not supplying enough pressure to the oil pressure sensor. This can be tested by putting an oil pressure gauge into where the oil pressure sensor normally goes, bypassing the circuitry that leads to the dash light for the oil pressure.

If it was the oil level sensor, then check for bad wiring.

Oct 26, 2010 | 2003 Dodge Neon

1 Answer

Oil sending unit is toast. What is the trick to changing it, besides having very small hands and can see around corners? 2003 gmv v8


Engine Oil Pressure Sensor / Switch Replacement Removal & Installation 4.3L Engine To Remove:
Oil pressure sensor removal/installation (4.3L engine shown) gm-04-43-572.gif

  1. Clean the area near the oil pressure sensor.
  2. Remove the distributor.
  3. Disconnect the electrical connector from the oil pressure sensor.
  4. Using J 41712 or equivalent, remove the oil pressure sensor from the fitting. NOTE: Note the orientation of the oil pressure sensor fitting before attempting to remove it. This is so it can be installed in the original position.
  5. Remove the oil pressure sensor fitting, if necessary.
To Install:
NOTE: If the fitting has been removed, clean and apply sealant to the threads before installing it.
  1. Install the fitting until snug, if it was removed.
    • Tighten the fitting to 11 lb ft (15 Nm). Continue to tighten the fitting until in the original position.
  2. Apply sealant to the threads of the sensor.
    • Install and tighten the sensor to 22 lb ft (30 Nm).
  3. Connect the electrical connector to the oil pressure sensor.
  4. Install the distributor.
  5. Check the engine oil level and adjust if necessary.
4.8L, 5.3L & 6.0L Engine To Remove:
  1. Remove the engine sight shield. chevy_aval15_02-04_opcon.gif

  2. Disconnect the oil pressure sensor electrical connector. chevy_aval15_02-04_opsocket.gif

  3. Using J41712 sensor socket or equivalent, remove the oil pressure sensor.
To Install:
  1. Apply sealant GM P/N 12346004, (Canadian P/N 10953480), or equivalent, to the threads of the sensor.
  2. Using J41712 sensor socket or equivalent, install the oil pressure sensor.
    • Tighten the sensor to 15 ft. lbs. (20 Nm).
  3. Connect the oil pressure sensor electrical connector.
  4. Install the engine sight shield.
6.6L Diesel Engine To Remove:
  1. Raise and safely support the vehicle NOTE: Clean the area around the sensor. Do not allow debris to enter the engine
    6.6L Oil pressure sensor gm_trk_sil25_02-04_66_oil_press_sensr.gif

  2. Remove or disconnect the following:
    • Engine oil pressure sensor electrical connector
    • Engine oil pressure sensor using a suitable tool
To Install:
  1. Apply sealant to the threads of the oil pressure sensor
  2. Install or connect the following:
    • Engine oil pressure sensor and tighten the sensor
      1. Torque to: 22 ft. lbs. (30 Nm)
    • Engine oil pressure sensor electrical connector
  3. Lower the vehicle
  4. If required, check and adjust the engine oil level
  5. Test drive the vehicle to confirm the repairs
8.1L Engine To Remove:
  1. Remove the engine appearance cover.
  2. Disconnect the electrical connector from the oil pressure sensor.
  3. to remove the sensor.
To Install:
  1. If installing the old sensor, apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent, to the threads of the sensor.
  2. Using J 41712 or equivalent, install the sensor.
    • Tighten the sensor to 22 lb ft (30 Nm).
  3. Connect the oil pressure sensor electrical connector.
  4. Install the engine appearance cover.
prev.gif next.gif

Sep 18, 2010 | 2003 GMC Sierra 1500

1 Answer

The oil sensor needs to be replaced where is it


  1. Remove the engine sight shield.
  2. Disconnect the oil pressure sensor electrical connector.
  3. Using J 41712 or equivalent, remove the oil pressure sensor.

    0996b43f802053c4.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Using J 41712 or equivalent, remove the oil pressure sensor-8.1L engines

To install:
  1. Apply sealant to the threads of the oil pressure sensor.
  2. Using J 41712 or equivalent, install the oil pressure sensor.
    1. Tighten the sensor to 22 ft. lbs. (30 Nm).

  3. Connect the oil pressure sensor electrical connector.
  4. Install the engine sight shield.

Nov 15, 2009 | 2001 Chevrolet Silverado 2500HD

1 Answer

Oil sensor replacement for 2006 GTO


COST Around $25 - $35 and Fallow these Instructions PLEASE RATE ME!!!!!

Engine Oil Pressure Sensor and/or Switch Replacement

Tools Required
  • J41712 Oil Pressure Switch Socket
Removal Procedure
Disconnect the oil pressure sensor electrical connector (1).
  1. Important: Clean the area around the sensor before removal. This prevents debris from entering the engine. Use J41712 to remove the oil pressure sensor from the engine block.
Installation Procedure
  1. If installing the old sensor, apply thread sealant GM P/N 12346004, (Canadian P/N 1093480), or equivalent. Notice: Refer to Fastener Notice in Service Precautions.
  2. Use to install the J41712 oil pressure sensor to the engine block. Tighten the engine oil pressure sensor to 35 Nm (26 ft. lbs.) .Connect the oil pressure sensor electrical connector (1).

Oct 04, 2009 | 2006 Pontiac GTO

1 Answer

Where is the oil sending unit on a 2001 4.3 liter vortec v6


ENGINE OIL PRESSURE SENSOR OR SWITCH REPLACEMENT

TOOLS REQUIRED
J 41712 Oil Pressure Switch Socket

REMOVAL PROCEDURE

IMPORTANT: Clean the area around the sensor and Distributor before removal. Do not allow debris to enter the engine.

89348473

  1. Remove the distributor.
  2. Disconnect the engine oil pressure sensor electrical connector.
  3. Remove the engine oil pressure sensor using the J 41712. IMPORTANT: Note the alignment of the engine oil pressure sensor fitting prior to removal.
89348474

  1. Remove the engine oil pressure sensor fitting, if necessary.
INSTALLATION PROCEDURE

89348474

  1. Apply sealant GM P/N 12346004 or equivalent to the threads of the fitting and/or the engine oil pressure sensor. NOTE: Refer to Fastener Notice in Service Precautions.
  2. Install the engine oil pressure sensor fitting, if removed. Tighten Tighten the engine oil pressure sensor fitting to 15 N.m (11 lb ft) .
89348473

  1. Install the engine oil pressure sensor. Tighten Using the J 41712, tighten the engine oil pressure sensor to 30 N.m (22 lb ft) .
  2. Connect the engine oil pressure sensor electrical connector.
  3. Install the distributor.
  4. Check and adjust engine oil level.

Jun 05, 2009 | 2001 Chevrolet Blazer

Not finding what you are looking for?
1991 Chrysler New Yorker Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...