The pump comes out under back seat the cover off lock ring removed not attached to cover please help

Yes, remove back seat, it is under the passenger side, just pull back the carpet. It is a circular cover held on by 6 screws. Be sure to disconnect your negative battery cable before performing any work on the fuel pump/ sending unit assembly.

You will need to remove your seat in the back of the car. The pump is under the drivers side rear back seat. You will have to remove the floor cover. You should see a panel. remove panel on floor and you will see the top of the fuel pump. There may be a lock ring holding it in which you would move counter clockwise and then the pump should come out

TO CHANGE FUEL PUMP YOU HAVE TO RELIEVE FUEL PRESSURE FIRST.LIFT THE LEFT REAR SEAT CUSHION POSITION THE CARPET ASIDE.REMOVE THE SCREWS AND THE FUEL PUMP MODULE ACCESS COVER.DISCONNECT THE FUEL PUMP MODULE AND ELECTRICAL CONNECTORS.REMOVE FUEL PUMP FUEL VAPOR CONTROL TUBE ASSEMBLY VALVE ELECTRICAL CONNECTOR.USING A SUITABLE FUEL PUMP LOCK RING REMOVER.ROTATE THE LOCK RING COUNTERCLOCKWISE AND REMOVE FUEL PUMP MODULE ASSEMBLY CAREFULLY.PUT EVERY THING BACK IN VISA VERSA.BECAREFUL WHEN WORKING ON FUEL SYSTEM.DONT MAKE NO SPARKS WHEN REMOVING FUEL PUMP MODULE LOCK RING.USE LOCK RING TOOL DONT USE HAMMER AND A METAL PUNCH WILL MAKE A SPARK CAUSE EXPLOSION.

The ring is what locks the cover in place, turn the ring to unlock and remove

Hi. here's how to change the fuel pump. The actual electric fuel pump is in the tank on the right side. The tank is directly below the rear seat. If you remove the seat bottom you will find a 6 inch or so cover. Under the cover there is a plastic, threaded collar that locks the fuel pump into the tank. The driver's side also has a pump, but it works only my venturi effect from the electric pump on the other side. This pump is used to equalize the fuel level from left to right. The drive shaft tunnel prevents all but the very top of the tank from communicating left to right.

should be 4 bolts holding seat into floor pan, one under each corner of the seat. Remove bolts, unplug any power connections , seat should come right out.

Removal & Installation WARNING Extreme caution should be taken when removing the fuel tank from the vehicle! Ensure that all removal procedures are conducted in a well ventilated area! Have a sufficient amount of absorbent material in the vicinity of the work area to quickly contain any fuel spillage. NEVER store waste fuel in an open container, as it presents a serious fire hazard!

This procedure will require a new fuel pump gasket for pump installation, so be sure to have one before starting.

1. Relieve the fuel system pressure.
   
2. Disconnect the negative battery cable.
   
3. Remove the rear seat cushion and unplug the electrical connectors from the fuel pump.
   
4. Unfasten the four pump access cover screws and remove the cover.
   
5. If equipped, unplug the pump electrical connector located under the cover.
   
6. Unfasten the fuel line clip(s) and disconnect the line(s) from the pump.
   
7. Use a fuel pump locking ring removal tool or a brass drift and a hammer to unfasten the pump locking retaining ring.
   
8. Remove the fuel pump and the gasket from the tank.
   

To install:

1. Install a new gasket and place the pump into position in the tank.
   
2. Install the pump locking retaining ring.
   
3. Connect the fuel line(s) to the pump and install the line retaining clip(s).
   
4. If equipped, attach the fuel pump electrical connection(s).
   
5. Install access cover, then tighten the retainers.
   
6. Attach the pump electrical connector(s).
   
7. Install the rear seat cushion.
   
8. Connect the negative battery cable.
   
9. Start the car and check for proper operation.
   

Hello dorina_jorge: My name is Roger and I will help you. The fuel pump is located in the fuel tank. You can access the pump by removing the rear seat cushion. After removal locate the pump cover plate. Should be in the middle of the floor pan. Remove the screws. There are 4 of them. Unplug the wire harness and lift the cover up. Remove the fuel lines. ( be careful as they may be under pressure ). Remove the lock ring this screws down and lift out the fuel meter assembly. Make sure to replace the gasket when you reinstall the pump. Reverse procedure when done. Should you need further help please just ask. Please rate the answer. This way I know it was helpful. Thank You for using Fix Ya. Roger

Hello rand1958: My name is Roger and I will help. The fuel pump is located in the fuel tank. You can access the pump by removing the rear seat cushion. Remove the 4 screws in the floor cover. unplug the fuel pump wire harness. Remove the fuel line locks. BE CAREFUL as fuel lines may be under pressure. Remove pump lock ring to remove the fuel pump. I would also recommend replacing the fuel filter at the same time. Should you need further help please just ask. Please rate the answer as this way I know it was helpful. Thank You for using Fix Ya. Roger

hope this helps...
Pump Module—Left Side

1. Release the fuel pressure.
   
2. Disconnect negative battery cable.
   
   NOTE The fuel level of the vehicle must be below 5/8 of a tank before you remove the module lock-rings. If it is above that you can spill fuel in the vehicle.
   
   
3. Drain partial fuel from fuel tank through the filler tube. Use a hard nylon tube, with a 30° cut on the end, to push the check valve open to drain fuel from tank.
   
4. Remove the rear lower seat cushion.
   
5. Push seat back and up to remove seat cushion.
   
6. Fold back the foam pad covering access cover for modules.
   
7. Disconnect the electrical connector from left side module.
   
8. Mark the module orientation.
   
9. Use special tool 9340 to remove left side module lock ring.
   
10. Drain fuel from left side of fuel tank. Lift module up enough to push hose into tank and drain. Do not spill fuel in interior of vehicle.
    
11. Disconnect the electrical connector for the left side fuel level card from bottom of the module top.
    
12. Disconnect the electrical connector for the right side fuel level sending card.
    
13. Lift module top half off and tip lower half on its side to drain remaining fuel from the reservoir.
    
14. Remove wire from module.
    
15. Use a screwdriver to separate the locking tabs on the level sending card.
    
16. Lift level sending card straight up and out of module.
    
17. Disconnect the electrical wiring from module.
    
18. Remove level sending card.
    

To install:

1. Install level sending card, make sure that the locking tabs are locked on the card.
   
2. Route wires in the proper location.
   
3. Install module top to module bottom.
   
4. Connect the electrical connectors for right side fuel level sending card, left side module card and fuel pump.
   
5. Install module and align marks on the module for proper orientation.
   
6. Install module lock-ring.
   
7. Use special tool #9340 to tighten left side module lock ring.
   
8. Connect the electrical connector to left side module and install plastic access cover.
   
9. Fold the foam pad covering access cover for modules back into place.
   
10. Install rear lower seat cushion
    
11. Rear lower seat cushion installed.
    
12. Fill fuel tank.
    
13. Connect negative battery cable.
    
14. Fill fuel tank. Use the scan tool to pressurize the fuel system. Check for