Question about Porsche Cayenne

1 Answer

Replaced bulb,still works a few times, then stops operating in front but works at rear.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Porsche Expert
  • 330 Answers

Hello there
would you tell me the year+model of your Porsche?
proporsche

Posted on Jan 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clio wiring diagram


one of the common probs is the hazard switch faulty it can stop one side or other working intermittant. when problem happens operate hazard switch a few times and check all 4 work ok. the bulb holders are also poor if its just the front change the relevant bulb holder the only other is the poss is one of the inline harness connectors under bonnet or fascia. good luck.

Sep 29, 2016 | 2005 Renault Clio 1.4

1 Answer

Fuse blows out 5-10 min after replacement


Check all your wires ,make none have rubbed and exposed the bare wire .vibrations might cause the wire to short out on metal

Apr 01, 2014 | 2005 Chevrolet Suburban

1 Answer

Town and counrty front right signal light flashing faster, rear light stop flashing


the signal indicator lights are suppose to flash in perticular time interval which is connected to a timer relay when the light flashes faster that means the other light is not working and the relay is getting double the current and moving faster so check the other light either the bulb is fuse or the current is not reaching up to the bulb

Aug 22, 2012 | 2005 Chrysler Town & Country

1 Answer

Changing the interior map light


The bulbs is replaced from the back of the overhead console with 1/4 turn bulb holders.

the overhead console ( non rail version ) is held up with spring clips.

Open the rear compartment, and grab the rear corners and pull down 1 at a time. They are very hard to pull the 1st few times. Once you have the read released, there is another set of spring clips in the front, so be careful how far down you pull the rear, until the front is released.

Once you can see the back of the overhead console, you will see the 1/4 turn bulb holders for the map and interior lights.

Sep 18, 2011 | 2005 Ford F-150

2 Answers

What could cause my right front turn signal to not work some of the time. The bulb was checked and even replaced but did not solve the problem. Each time the car is turned off, the signal will work for a...


Some of th intermitent problems with lights can be traced to bad ground connection since flasher bulbs draw quite a bit of current. Some cars use the car bodywork as the ground connection. If the rear lamp flashes faster than normal when the front one does not you have a bad connection. Check the bulb holder and the ground connection.

Nov 24, 2009 | 2003 Land Rover Range Rover

1 Answer

The turn signals do not work on 2000 nissan exterra.Fuse was blown. Replaced and blew again after a few seconds.


1.Remove front & Rear turn signal Bulbs.
2.Replace Fuse.
3.Signal on.
4.Fix rear Signal Bulb.
5.Fix Front Signal Bulb.
7.If your Fuse blown.
8.Defect is There.

Jun 11, 2009 | 2000 Nissan Xterra

2 Answers

Right turn signal flashes too fast I have replaced my front turn signal bulbs a few times and within a couple days they stop working and the blinker on the inside flashes very fast. I have looked for the...


littlejevans: The turn signal flasher works against the resistance through the bulbs both front and rear. The Malibu's had a problem with the rear light sockets which caused problems with the tail lights. Have you checked to see if the rear lights are functioning correctly?

May 29, 2009 | 2005 Chevrolet Malibu

1 Answer

Right blinker dead left blinker works 2002 buick lesabre limited


RIGHT BLINKER dead ,front,back, or both..???? If front works, and rear doesn"t (REPLACE REAR BULB).....and vice a versa....If rear and front both don't work replace the FLASHER ..Flasher is located in the FUSE block area.......Listen to the operation of the LEFT or RIGHT flasher operation and you should notice a dirrerence....

May 17, 2009 | 2002 Buick LeSabre

1 Answer

Jeep Liberty Left Rear Turn Signal Not Working


sounds like the bulb you have is the wrong resistance the new noen bulbs will do this

Nov 16, 2008 | 2004 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

yadayada
yadayada

Level 3 Expert

74945 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...