Question about 1990 Acura Legend

1 Answer

Were do the negative cable connect on transmission

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 541 Answers

Bolted down with one transmission to engine bolt

Posted on Jan 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Speedometer stopped working and transmission won't shift


Make sure all the connectors are connected to the transmission input and output shaft sensors. Also, check to see if the vehicle speed sensor is connected as well as the range switch. If all are connected, disconnect both battery cables from the battery and hold the positive cable and the negative cable to each other for about 30 seconds. Doing this drains the capacitor in the ECM and resets the system. Reconnect the cables to see if problem is still present.

Feb 21, 2015 | 2000 Saturn Ls 4dr Sedan

1 Answer

Just replaced the transmission in the truck and everything will come on inside the truck but when you try to start the engine everything goes out.


Clean and retighten battery post connections, Check the negative grounding point-where the negative cable grounds to frame. And check the positive cable connection on the battery. Sounds like a loose connection somewhere.

Aug 16, 2014 | Cars & Trucks

1 Answer

Where to connect negative battery cable 2005 altima


It mounts to the front side of the transmission. It is a larger bolt and it is located under the battery tray.

Nov 16, 2012 | 2005 Nissan Altima

1 Answer

Need to know where the non-battery side of the cable is affixed. Frame, engine, transmission, etc?


The negative cable is usually connected to the engine block.
The positive cable is usually connected to the starter solenoid.
There may be one or two smaller gauge positive cables connected to main power distribution boxes.

Aug 26, 2011 | Mazda B-Series Truck Cars & Trucks

1 Answer

Where is the starter located on my 2003 nissan sentra ser


Starter Motor -located to articulate with flywheel that has gear teeth between the engine and transmission accessible from down below. REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
  3. Lightly lower the transmission to make room and pull out the dipstick tube.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  5. Install or connect the following:
    • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
    • Harness connector
    • Connector bracket to the front mount bracket
    • Dipstick tube
    • Transmission into position
    • 4 rear mounting bracket bolts
    • Negative battery cable
  6. Remove the transmission jack
WITH MANUAL TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  3. Install or connect the following:
    • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
    • Harness connector
    • Connector bracket to the front mount bracket
    • Negative battery cable
1.6L and 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter
    To install:
  3. Install or connect the following:
    • Starter and torque the bolts to 70 inch lbs. (8 Nm)
    • Starter electrical connections
    • Negaative battery cable
Maxima
  1. Remove or disconnect the following:
    • Negative battery cable
    • Air duct
    • Harness protector from the harness
    • Starter wiring at the starter
    • Starter-to-engine bolts
    • Starter from the vehicle

      Image 89612G12l Not Found

    To install:
  2. Install or connect the following:
    • Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) and the short bolt to 22-30 ft. lbs. (30-41 Nm)
    • Starter wiring
    • Harness protector
    • Air duct
    • Negative battery cable
Altima
  1. Remove or disconnect the following:
    • Negative battery cable
    • Air inlet tube
    • Harness bracket
    • Wiring at the starter
    • Starter
    To install:
  2. Install or connect the following:
    • Starter and torque the bolts to 60 inch lbs. (7 Nm)
    • Starter electrical connectors
    • Harness bracket
    • Air inlet tube
    • Negative battery cable

Nov 03, 2010 | 2003 Nissan Sentra

1 Answer

How to get to starter on 2003 traikblazer


Removal & Installation 4.2L Engine To Remove:
  1. Disconnect the negative battery cable from the battery.
  2. Disconnect the brake booster hoses from the engine. Starter gm-02-42-1398.gif

  3. Remove the positive battery cable and s-terminal lead from the starter.
  4. Remove the starter from the engine.
To Install:
  1. Install the starter to the engine. Tighten the nut and bolt to 37 ft-lb (50 Nm).
  2. Install the positive battery cable and s-terminal to the starter. Tighten the battery cable nut to 80 in-lb (9 Nm). Tighten the s-terminal nut to 20 in-lb (2.3 Nm).
  3. Connect the vacuum brake booster hose to the engine.
  4. Connect the negative battery cable to the battery.
5.3L & 6.0L Engines To Remove:
  1. Disconnect the negative battery cable from the battery.
  2. Raise and support the vehicle.
  3. Remove the rear steering gear crossmember from the frame. Starter gm-02-53-1399.gif

  4. Detach the wire harness from the transmission oil cooler line bracket.
  5. Detach the transmission oil cooler line bracket from the engine.
  6. Remove the right transmission cover bolt from the transmission cover.
  7. Detach the starter from the engine.
  8. Slide the starter forward and remove the transmission cover.
  9. Remove the heat shield from the starter.
  10. Position the starter so that it can pass between the engine oil pan and transmission oil cooler lines.
  11. Detach the starter lead and battery positive cable from the starter.
  12. Remove the starter from the vehicle.
To Install:
  1. Place the starter between the engine oil pan and transmission oil cooler lines.
  2. Attach the battery positive cable to the starter and starter lead. Torque the battery positive cable nut to 80 in-lb (9 Nm). Torque the starter lead nut to 30 in-lb (3.4 Nm).
  3. Install the heat shield to the starter.
  4. Attach the starter from the engine. Torque the bolts to 37 ft-lb (50 Nm).
  5. Install the right transmission cover bolt into the transmission cover. Torque the bolt to 80 in-lb (9 Nm).
  6. Attach the transmission oil cooler line bracket to the engine. Torque the bolt to 80 in-lb (9 Nm).
  7. Attach the wire harness to the transmission oil cooler line bracket.
  8. Install the rear steering gear crossmember onto the frame.
  9. Lower the vehicle.
  10. Connect the negative battery cable to the battery.
prev.gif next.gif

Aug 19, 2010 | 2003 Chevrolet TrailBlazer

1 Answer

How do i change the starter on a 2000 nissan altima


I hope this helps:

REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
  4. Lightly lower the transmission to make room and pull out the dipstick tube.
  5. Remove or disconnect the following:
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  6. Install or connect the following:
    • Starter
    • Starter bolts. Tighten the bolts to 30–37 ft. lbs. (40–50 Nm).
    • Harness connector
    • Connector bracket to the front mount bracket
    • Dipstick tube
    • Transmission into position
    • 4 rear mounting bracket bolts
  7. Remove the transmission jack
    • Negative battery cable
WITH MANUAL TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  3. Install or connect the following:
    • Starter
    • Starter bolts. Tighten the bolts to 30–37 ft. lbs. (40–50 Nm).
    • Harness connector
    • Connector bracket to the front mount bracket
    • Negative battery cable
1.6L and 2.0L Engines
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter from the vehicle
    To install:
  2. Install or connect the following:
  3. Install the components in the reverse order of removal.
Maxima
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Air duct
    • Harness protector from the harness
    • Starter wiring at the starter
    • Starter-to-engine bolts
    • Starter from the vehicle Fig. 1: Starter location and mounting detail — Maxima with a manual transaxle 89612g12.gif
    To install:
  2. Install or connect the following:
    • Starter
    • Starter attaching bolts. Tighten the long bolt to 57–72 ft. lbs. (77–98 Nm) and the short bolt to 22–30 ft. lbs. (30–41 Nm).
    • Starter wiring
    • Harness protector
    • Air duct
    • Negative battery cable
  3. Start the engine a few times to make sure of proper operation.
Altima
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Air inlet tube
    • Harness bracket
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter from the vehicle
    To install:
  2. Install the components in the reverse order of removal.
prev.gif next.gif

Jul 13, 2010 | 2000 Nissan Altima

1 Answer

2004 jeep liberty replacing the starter


2004 Jeep Liberty 4WD 3.7L MFI SOHC 6cyl
Starteer - Removal & Installation

2.4L & 3.7L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the starter mounting bolts.
  4. On the 3.7L engine, the left side exhaust pipe and front driveshaft must be disconnected.
  5. Disconnect the starter solenoid harness connections.
  6. Remove the starter.
To install:

8222c5e.jpg

Fig. Starter mounting: 2.4L engine

1ab95e7.jpg

Fig. The starter position for the 3.7L engine
  1. Connect the starter solenoid wiring connectors.
  2. Install the starter and torque the bolts to 40 ft. lbs. (54 Nm).
  3. On the 3.7L, the left side exhaust pipe and front driveshaft.
  4. Install the negative battery cable and check for proper operation.

2.8L Engine
  1. Disconnect and isolate negative battery cable.
  2. Raise and support vehicle.
  3. Disconnect solenoid wire connector from solenoid terminal
  4. Remove battery cable from stud on starter solenoid.
  5. Remove 3 starter mounting bolts.
  6. Remove starter from transmission bellhousing.
To install:
  1. Position starter motor to transmission housing.
  2. Connect battery cable solenoid terminal wire harness connector to connector receptacle on starter solenoid. Always support starter motor during this process. Do not let starter motor hang from wire harness.
  3. Install battery cable eyelet terminal onto solenoid B(+) terminal stud.
  4. Install nut securing battery cable eyelet terminal to starter solenoid B(+) terminal stud.
  5. Refer to torque specifications.
  6. Position starter motor and install 3 bolts. Tighten 3 bolts in this sequence: top bolt, bottom bolt, middle bolt. Refer to torque specifications.
  7. Lower vehicle.
  8. Connect negative battery cable.

Also can review the Service Repair Manual for Jeep KJ Liberty

I really hope help you with this (remember rated this help) Good luck.

Oct 04, 2009 | 2004 Jeep Liberty

1 Answer

Vss location on 2000 miata


VEHICLE SPEEDOMETER SENSOR REMOVAL/INSTALLATION
  1. Disconnect the negative battery cable.
  2. Drain the transmission oil.
  3. Disconnect the vehicle speedometer sensor connector.
  4. Remove the vehicle speedometer sensor.
  5. Apply transmission oil to a new O-ring and install it on a new vehicle speedometer sensor.
  6. Install the vehicle speedometer sensor. Tightening torque 69.5 - 95.4 inch lbs.
  7. Connect the vehicle speedometer sensor connector.
  8. Add the specified amount and type of transmission oil.
  9. Connect the negative battery cable.

Oct 08, 2008 | 2000 Mazda MX-5 Miata

2 Answers

Changing the starter on my 99 tahoe


Starter Escalade, Suburban, Tahoe, Yukon, Denali, Denali XL, Yukon XL, 1999 – 2005 REMOVAL&INSTALLATION
Removal & Installation
4.8L, 5.3L And 6.0L Engines
CAUTION Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures.
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle.
  3. Remove or disconnect the following:
    • Protective shields, as necessary
    • Starter solenoid shield
    • Starter-to-transmission close out cover bolt
    • Engine oil level sensor connection
    • On 4WD, front axle mounting bracket through bolt nut
  4. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
    • Mounting bolts from the engine block. Slide the starter forward until the starter clears the transmission.
    • Starter transmission close out cover
    • Positive battery cable and wiring harness from the starter
    • Starter from the vehicle 0900c152800a6916.jpgStarter removal—4.8L, 5.3L and 6.0L engines
To install:
  1. Install or connect the following:
    • Starter
    • Positive battery cable to the starter. Tighten the nut to 12 ft. lbs. (16 Nm).
    • Starter transmission close out cover
    • Mounting bolts to the engine block and tighten to 37 ft. lbs. (50 Nm)
  2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
    • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
    • Engine oil level sensor connection
    • Starter-to-transmission close out cover bolt
    • Starter solenoid shield
    • Protective shields as necessary
  3. Remove the safety stands.
  4. Lower the vehicle.
  5. Connect the negative battery cable.
5.7L And 7.4L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Mounting bolts and shims
    • Wires
    • Heat shield
    • Starter
To install:
  1. Install or connect the following:
    • Starter
    • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
    • Heat shield. Torque the bolts to 53 inch lbs. (6 Nm) and the nuts to 35 inch lbs. (3 Nm).
    • Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm).
    • Negative battery cable
6.5L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cables
    • Mounting bolts/nuts and shim, if used
    • Starter
    • Wires
    • Heat shield and bracket 0900c152800a6917.jpgExploded view of the starter motor—6.5L engine
To install:
  1. Install or connect the following:
    • Heat shield and bracket. Torque the bolts to 13 ft lbs. (17 Nm).
    • Wires. Torque battery wire nut to 89 inch lbs. (10 Nm), and ignition nut to 18 inch lbs. (2 Nm).
    • Starter
    • Mounting bolts/nuts and shim, if used. Torque the bolts to 33 ft lbs. (45 Nm) and the nut to 75 inch lbs. (8.5 Nm).
    • Negative battery cables
8.1L Engine
  1. Remove or disconnect the following:
    • Negative battery cable
    • On 4WD, front axle mounting bracket through bolt nut
  2. Reposition the front axle mounting bracket through bolt until the bolt tip is flush with the support bushing. Do not remove the bolt.
    • Positive battery cable nut
    • Positive cable from the solenoid
    • Engine harness ground nut and ground from the solenoid
    • Mounting bolts and starter
    • Heat shield bolts, nut and shield, if necessary
To install:
  1. Install or connect the following:
    • Heat shield, bolts and nut if removed. Tighten the bolts to 35 inch lbs. (3 Nm) and the nut to 44 inch lbs. (5 Nm).
    • Starter and bolts. Tighten to 37 ft. lbs. (50 Nm).
    • Ground wire and nut. Tighten to 30 inch lbs. (3.4 Nm).
    • Positive cable and nut. Tighten to 80 inch lbs. (9 Nm).
  2. Reposition the front axle mounting bracket through bolt until the bolt is fully seated.
    • Front axle mounting bracket through bolt nut and tighten to 70 ft. lbs. (95 Nm)
    • Negative battery cable

Sep 28, 2008 | 1999 Chevrolet Tahoe

Not finding what you are looking for?
1990 Acura Legend Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...