Question about 1992 Toyota Corolla

Open Question

I want to install an ammeter to my toyota car model 1992. Where should I tap the wire ?

Posted by on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 65 Answers

SOURCE: Do you have Electrical Wiring

i will find it .just hang on for a while

Posted on Aug 16, 2011


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Battery dead

this is called phantom drain
if you have an ammeter, this is easy
if not pure H3LL !!!

im and retired, ET. ask for details.
this page covers all ways to find it, even a $1 way, ASK

Jan 19, 2014 | 1992 Toyota Corolla

1 Answer

My 1992 Toyota pickup starts and runs for7-8 miles then blows the AM2 fuse any suggestion as why?

there is a short in that line.

there are only 2 ways to fix it.
the best is using and ampclamp type DC ammeter.
this makes the job childs play.
cost about 1hr shop labor.
if you want to know who shorts. its all here
alldata dot com.

Oct 08, 2013 | Toyota Pickup Cars & Trucks

1 Answer

Hi i want a wiring diagram of toyota corolla 92 model pls


Oct 26, 2012 | 1992 Toyota Corolla

1 Answer

How to replace a starter for a 96 toyota 4runner, 4wd, 6cyl

  1. Connect the battery ammeter to the starter as shown in the illustration.

0900c15280060948.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 4: Make the connections to the battery, ammeter and starter as shown here

  1. Check the rotation of the starter, it must be smooth and steady with the pinion gear moving outwards. Compare the ammeter reading to the starter specifications chart.


See Figure 5
Replacing the starter while the engine is cold is recommended. A hot engine can result in personal injury.
  1. Disconnect the negative battery cable.
  2. Remove the nut and disconnect the battery cable from the magnetic switch on the starter motor.
  3. Disconnect the remaining electrical connections at the starter.
  4. Remove the nuts and/or bolts securing the starter to the bell housing, then pull the starter toward the front of the vehicle to remove.

To install:
  1. Insert the starter into the bell housing being sure that the starter drive teeth are engaged with the flywheel teeth, not jammed against the flywheel.
  2. Tighten the attaching hardware to 29 ft. lbs. (39 Nm) and replace all electrical connections.

0900c15280060949.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Exploded view of a common starter mounting found on Toyota trucks

  1. Connect the positive battery cable (starter wire) to the starter.
  2. Connect the negative battery cable.


See Figure 6
The starter relays on most of your Toyota trucks are located either in the relay block in the engine compartment or on the driver's side junction block. The cover for the relay compartments should be marked, "starter'' or the relay will have a part number with a suffix of 28300-XXXXX. Simply locate the relay, pull it out, and install a new one if needed.

0900c1528006094a.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: The relay may be located in the driver's side junction block or in the engine compartment relay block

Feb 05, 2011 | 1996 Toyota 4Runner

1 Answer

How to install headlights on a 1992 toyota 4x4 pickup

To remove old light, remove screws holding the trim around the headlight. Some models require removing the grille to access them. Headlight should pull out and you can detach the plug. Install in reverse order.

Sep 01, 2010 | 1992 Toyota Pickup

3 Answers

How to change the Starter on a 1989 toyota camry

Gasoline Engines
  1. Disconnect the cable from the negative terminal of the battery.

Fig. 5: Exploded view of the starter motor mounting-5S-FE engine shown, others similar
  1. On 1992-96 models with cruise control, remove the battery.
  1. Also on 1992-96 models with cruise control, remove the actuator cover and disconnect the wiring harness. Remove the three bolts and then lift out the cruise control actuator. Remove the bracket from beneath the actuator and put aside.
  1. Peel the rubber boot away and remove the nut and disconnect the negative battery cable from the magnetic switch terminal on the starter. Disconnect the electrical connector also located on the magnetic switch.
  1. Support the starter by hand and remove the two mounting bolts.
  1. Remove the starter from the transaxle.
To install:
  1. Place the starter motor in the transaxle and support by hand.
  2. Install the two mounting bolts and tighten them to 29-31 ft. lbs. (39-42 Nm).
  3. Connect the connector to the magnetic switch. Place the battery cable on the switch terminal and install the nut. Tighten the nut and position the rubber boot over the cable.
  4. Using the ignition switch, "bump'' the starter over a few times and check for proper operation.

Hope helps.

Aug 11, 2010 | 1989 Toyota Camry

2 Answers

I have a 1996 Toyota Tercel with an aftermarket alarm system that I'm uninstalling. There are two large gauge wires from the ignition bundle, black/yellow & white/red that have taps on them. A third...

something is obviously wrong with the wiring try reinstalling the old system and letting a n experienced mechanic install this other one for you wiring is everything

Sep 06, 2009 | 1996 Toyota Tercel

1 Answer

It sounds like my 1992 toyota needs a starter, but how do I know for sure

Is your battery is fully charged, your clamps on your battery clean and tight? Try this put your headlights on crank your engine if lights dim serverly and you hear Click..Click...Click..Your starter/solenoid is shot.If it srarts with a jump with the other car racing it's engine it could be your battery does not have the cranking amps.You can try to tap the solenoid with a handle of a screwdriver, or quickly jump the wires on the solenoid and see if the engine cranks.Good Luck

Sep 06, 2009 | 1992 Toyota Pickup

2 Answers

1992 corolla GTI wont start sometimes

the starter solenoid contacts need to be replaced. if contacts are good better put a relay to the solenoid.

May 29, 2009 | 1992 Toyota Corolla

Not finding what you are looking for?
1992 Toyota Corolla Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides