Question about 2006 Chrysler Pacifica

Open Question

2006 Pacifica ABS light always on and setting hard code for L/F Wheel speed sensor circuit. Sensor was replaced but light did not go off, Sensor was found to be faulty and was replaced again under warranty. Light still on and same hard code for L/F wheel speed sensor cir. setting. Ohmed sensor and it ohms at 577 ohms. Put volt meter across speed sensor connector with key on. read only 6 volts but according to Diag. info. it should be 12 volts. Disconnected connector at ABS module and found I could read sensor and it was ohming out at 557 ohms there as well. What is it? ABS module faulty? or am I missing something still?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 412 Answers

SOURCE: ABS light and trac control light off

YOU NEED TO HAVE ABS CONTROLLER SCANNED FOR DIAGNOSTIC TROUBLE CODES..THE SYSTEM HAS DETECTED A FAULT..A GOOD SCAN WILL YOU LEAD DOWN THE PATH TO FIXING THE PROBLEM..YOU CAN SEE IF WHEEL SPEED SENSORS ARE NOT WORKING,IF YOU CAN'T COMMUNICATE WITH CONTROLLER,ETC..LET ME KNOW WHAT IS FOUND

Posted on Jun 22, 2009

  • 242 Answers

SOURCE: Same ABS problem with my 2006 Pacifica

Go to a diffrent mechanic! There is only one light for your ABS and thats on your dash. If the light came on after the brakes were installed, I would suspect that your mechanic didn't open the bleeder screw on the calipers before depressing the piston. This would force fluid back to the ABS acumulator, setting off the light.

Posted on Aug 27, 2009

  • 1 Answer

SOURCE: 98 Honda Accord V6 automatic

You need to check to resistance of all solenoids of this transmission.
If you are referring to the solenoids on the front lower portion of the transmission, a 10 mm socket with a 3 inch extension and a ratchet will remove the solenoids. you can check them out of the vehicle. if one is out of spec, you must replace both b and c shift solenoid. Note Honda refers to these solenoids as solenoid and solenoid B. One more thing, if you disconnect the battery and take the battery and battery tray out, if is very easy to get to all the solenoids. Make sure you have the security code for the radio, or it may not have full function when powered up. Good Luck

Posted on Sep 16, 2009

Testimonial: "This fella appears to have been there and done that. Good info but I could still use a little more..."

johnjohn2
  • 5763 Answers

SOURCE: 2002 gmc abs light is on tested sensors with ohm

ohms shuold be 700-2000 ohms, next spin wheel by hand as fast as you can measure ac voltage should be 100mv or better. use a digital multi meter when testing. good luck.hope this helps.

Posted on Oct 02, 2009

Testimonial: "thanks will give it a try"

97F350diesel
  • 1326 Answers

SOURCE: Chrysler Pacifica ABS on

Not long at all, there located in each wheel. Worst case is about an hour per sensor...

Posted on Nov 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Abs codes c0040 and c0041 front wheel speed control sensor and circuit


Will be located near the wheel hub. As long as there is no physical damage I would guess you will be replacing the sensor

May 19, 2013 | 2005 Chevrolet Uplander

1 Answer

2006 ford crown vic abs code b1596


B1596 ABS Module Service Continuous Codes NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart.
Anti-Lock Brake System (ABS) Module Diagnostic Trouble Code (DTC) Index DTCs DTC Caused By Description Action B1342 ABS Module ECU is Defective INSTALL a new ABS module. REFER to Anti-Lock Brake System (ABS) Module in this section. B1484 ABS Module Brake Pedal Input Open Circuit Go To Pinpoint Test D . B1596 ABS Module Service Continuous Codes NOTE: If other DTCs are present, REPAIR them before installing a new component.
TURN the ignition switch to the OFF position and wait at least 30 seconds. Turn the ignition switch to the ON position. REPEAT the ABS self-test. If any DTCs are retrieved, REFER to the Anti-Lock Brake System (ABS) Module Diagnostic Code (DTC) Index. If no DTCs are retrieved, CARRY OUT a drive test above 15 km/h (9 mph), then REFER to the symptom chart. B1676 ABS Module Battery Voltage Out of Range Go To Pinpoint Test E . C1145 ABS Module Speed Wheel Sensor RF Input Circuit Failure Go To Pinpoint Test B . C1155 ABS Module Speed Wheel Sensor LF Input Circuit Failure Go To Pinpoint Test B . C1165 ABS Module Speed Wheel Sensor RR Input Circuit Failure Go To Pinpoint Test B . C1175 ABS Module Speed Wheel Sensor LR Input Circuit Failure Go To Pinpoint Test B . C1222 ABS Module Speed Wheel Mismatch Make sure the tires are the same size and correctly inflated. INSPECT the wheel speed sensor rings. CLEAR the DTC. TEST drive the vehicle. REPEAT the self-test. C1266 ABS Module ABS Valve Power Relay Circuit Failure Go To Pinpoint Test K . C1296 ABS Module Wheel Speed LF Signal Fault Go To Pinpoint Test C . C1297 ABS Module Wheel Speed RF Signal Fault Go To Pinpoint Test C . C1298 ABS Module Wheel Speed RR Signal Fault Go To Pinpoint Test C . C1299 ABS Module Wheel Speed LR Signal Fault Go To Pinpoint Test C . C1300 ABS Module ABS Hydraulic Pump Motor Circuit Failure Go To Pinpoint Test A . C1805 ABS Module Mismatched PCM and ABS Modules Do Not Match CHECK the part numbers. INSTALL the correct module. C2775 ABS Module TC ON/OFF Switch Stuck Failure Go To Pinpoint Test H . U0073 CAN Bus Control Module Communication Bus Off REFER to Section 418-00 . U1900 CAN Bus CAN communication Bus Fault - Receive error REFER to Section 418-00 . U2023 CAN Bus Fault received from External Node REFER to Section 418-00 .

Jan 14, 2013 | 2006 Ford Crown Victoria

1 Answer

How do I install a vehicle speed sensor in a 2006 chrysler pacifica 3.5L


here is the link for the part you need.


http://www.partsgeek.com/gbproducts/TC/17855-06015753.html?utm_source=google&utm_medium=ff&utm_content=TC&utm_campaign=PartsGeek+Google+Base&utm_term=2004-2006+Chrysler+Pacifica+ABS+Speed+Sensor+Replacement+2970068+Front+Left+04-06+Chrysler+ABS+Speed+Sensor+2005+05&fp=pp&gbm=a&gclid=CJzn5eXokLQCFQioPAodpREAXg



Simple as pie. Once you have the part in hand, You will see where it plugs in near the intake. Just follow it to the other end, remove and replace.


Should be a 10mm bolt holding it down, and to remove the plug, just press the retainer tab and pull out. New plug snaps right in.



Dec 10, 2012 | 2006 Chrysler Pacifica

2 Answers

Abs light on 2005 Pacifica


Wiring harness issues. the code doesn't men the sensor is the problem, it means a problem exists in the circuit of that sensor, that can be of course the sensor or the wiring or the computer. You need to the dealer to sort this out, a live data scanner is needed to look at the wheel speed sensors signal to see what is going on, that scanner costs big dollars. Many people yell and scream and call names when I suggest the dealer service dept, but that is what it takes so please don't shot the messenger. I speak form 35 years of experience.

May 24, 2012 | 2005 Chrysler Pacifica

3 Answers

The ABS light is on my 2006 Chrsyler Pacifica Touring


Each wheel has a sensor. Theres more to it than the sensors. have the repair shop check it over for you and recommend repairs.

May 31, 2010 | 2006 Chrysler Pacifica

1 Answer

Need to replace front abs speed sensors on 2006 pacifica .how do i do it


If you look at the front hub area with the wheel off, youll see a wire running up the knuckle you need to unplug the connector, the sensor it self is bolted right behind the wheel with a small 10mm bolt, just take that bolt out and pull the sensor out, you might have to use a small flat head screw driver, then just reinstall new sensor..

youll have to have the abs light reset if its on, you can disconnect the battery and it should do the trick

Apr 06, 2010 | 2006 Chrysler Pacifica

1 Answer

Pontiac G6 ABS Problem


when the ABS light comes on you will not hear or feel anything cause soon as the ABS light comes on the ABS is disabled
sounds like it is weather related (rain,snow)
i would check both rear wheel speed sensor harnesses for water intrusion if you see any corrosion (green) on the terminals replace both the hub and harness
if there is no corrosion then check resistance of the sensor also check for a short to ground
if that is ok then put some dielectric lube on the wheel speed sensor terminals and clear the codes and see what happens
intermittent problems can be hard to find
hope this helps

Dec 30, 2009 | 2006 Pontiac G6

1 Answer

Changed brakes andd ow ABS lite came on


Hi:
The most common part to cause the ABS light is a wheel speed sensor. You should remove your wheels and inspect the wheel speed sensors, and make sure the harnesses are in good shape, and the sensors are all in place, and clean. Brake part cleaner spray works well....

Dec 01, 2009 | 2006 Chrysler Pacifica

1 Answer

HOW TO REPLACE OR REPAIR WHEEL SPEED SENSOR


It is part of the bearing hub assembly.Very have to do without air tools,If setting multiple abs/tc code (wheel speed sensors) probably abs electronic module or chaffed wires on drivers side at ac lines by air box.Have big problems with this and probably will come back.

Jun 12, 2009 | 2005 Saturn Relay

Not finding what you are looking for?
2006 Chrysler Pacifica Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...