Question about 1999 Chrysler 300M

1 Answer

Code( p 1684 done ) on dash, after cranking but no fire,starts after sitting a while and then stops running ?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 541 Answers

P1684 means that the battery was disconnected in the last 50 starts or it died completly

Posted on Jan 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 corolla wont crank and start


Sounds like your ECM / ECU may need to be re-flashed at the dealer, have you tried pulling the codes? The check engine light does NOT need to be on for it to have codes stored. The starting issue could be caused by the TPS / MAF / MAP sensors, the flashing of the odometer could be something with your PSOM chip or your VSS sensor. Pull the codes see what you get.

Sep 13, 2015 | 2010 Toyota Corolla 1.8

1 Answer

Why does my 2002 Dodge Caravan Crank but wont start, check Oil Light on?


The oil light is the serious problem-it may mean the engine has lost oil pressure which is very dangerous. Don't drive with the oil light on- have a shop check your oil pressure with a mechanical oil pressure gauge. The previous owner's negligence in not changing the oil may have caused serious internal damage.
The code is not truly a diagnostic trouble code-it only indicates the battery has been disconnected within the last 50 starts, which would have erased any stored codes if there were any.

Jul 02, 2014 | Dodge Caravan Cars & Trucks

1 Answer

I have a crysler town &country lx 2003 the car would not start and gives the error codes: 0134+0135+1684+0300+0442+0455+0456 what is the cause of that .pls help .thanks


Code 134 and 135 are about the O2 sensor bank one sensor one.
Code 1684 is battery disconnect or loss of power to the PCM.
Code 300 is a random miss fire.
Codes 442 - 455 - and 456 are about a leaking EVAP system which vents fumes from the gas tank.
Its possible the PCM does not have voltage which would keep the car from starting.
Otherwise, you will have to figure out if the no-start is from an ignition or fuel problem to proceed.

Jun 29, 2012 | 2003 Chrysler Town & Country

1 Answer

Volvo 850 intermittant starting after sitting several days


The power stage module,can do this on you vehicle after a hot restart

Mar 06, 2012 | Cars & Trucks

3 Answers

A code APPEARED ON THE DASH IT WAS P1684 done. I need to know what that means. The car has been turning it self off, sometimes the oil light comes on but the car has had a recent oil change. It...


P1684 is "the battery has been disconnected within the last 50 starts".. I would start by inspecting your battery cables and have the battery itself tested.

Jan 04, 2011 | 1999 Chrysler 300M

1 Answer

After it stops, the car sit for about 2 hours or


Possible cause would be the coil breaking down. After the car starts and runs again and stops take a inline spark tester and connect between the coil and the spark plug wire to check for fire. If no fire then remove the coil and replace it. hope this will help you.

May 10, 2010 | 2001 Dodge Intrepid

1 Answer

I'm looking for the engine codes for a dodge intrepid codes are 1391 - 0134 - 1684.... I am trying to replace the oxygen sensors...how do you know which ones to replace?


1391 is a timing code cam or crank sensor
0134 bank 1 sensor 1 usually left front but double check
1684 doesn't match anything i know

Jan 30, 2010 | 1999 Dodge Intrepid

1 Answer

2002 malibu wont start


check for a bad crank sensor for this controls the timing of crank shaft. and sends info to pcm. it will cause no spark or pulse at injectors.the engine may start but cut out in a few minutes or seconds, of operation. have the car scanned for the problem code, if no scanner, any auto parts store will scan for free. good luck !!

Sep 19, 2009 | 2002 Chevrolet Malibu

1 Answer

Prelude 95


Disconnect alternator wiring; disconnect battery for a minute; reconnect battery & see if it starts & runs. If it works, replace alternator. If no difference, could be ECU error caused by alternator fault or carelessness with wiring when installing (spark to ECU perhaps). Check ECU codes (short the two-pin blue socket sitting loose on the transmission tunnel below the dash, switch ignition on and count any flashes of the check engine light (MIL))

Mar 30, 2009 | 1995 Honda Prelude

Not finding what you are looking for?
1999 Chrysler 300M Logo

Related Topics:

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...