Question about 2009 Dodge Journey

1 Answer

How do you get the 2 fastners out without breaking them?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I took a knife and pried the edges up and eased it from the wall.Then I used a screw driver to pry ithem out .Be careful ,don't rush.

Posted on Jan 10, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't remove front caliber


Holding the caliper to mounting bracket ?

Use a long 3/8 flexhead ratchet & socket,torx driver,
allen driver or whatever fastner you have

If it is something like a 12mm wrench-- use a long one
& break loose with a plastic or rubber hammer

Dec 16, 2012 | 1998 Ford Expedition

Tip

Avoid dropping nuts and bolts out of your socket, or wrench!!


How frustrating is it , when you are trying to start a nut, or bolt, in a tight area, or in a recessed area, where fingers don't fit? All you have to do, is tear off a small piece of paper, wrap the head of the nut, or bolt, and firmly push the fastner into the socket, or wrench. Not only will this keep the fastner snug in the tool, it will save potential hours of recovering lost fastners. Good luck...Coop

on Oct 06, 2010 | GMC Sierra 2500HD Cars & Trucks

1 Answer

The middle part to my bumper won't stay up. what can I do about that


go to the chevy dealer and get new plastic fastners, they can break over time and the bumper will come loose.

Oct 25, 2012 | 2003 Chevrolet Cavalier

1 Answer

How to get change tail light bulb


Lift gate up remove the 2 screws on the side of the light housing. The back of the light housing is held in by pin style snap fastner. Two ways 1 grab top and bottom pull hard and fast and hope to pop out both. 2 get a hold of the top and just pop it out turn it out grab and pull (always pull straight or the pins will break)

Nov 11, 2010 | 2005 Mercury Mariner

1 Answer

HOW DO I REPLACE A BRAKE LIGHT ON A 1987 MR2?


Open the rear bootlid behind the engine and there are two carpet panels on each side covering the light electrics. they are held in by fastners, push each fastner at the centre to release them.
Remove the carpet panel to get access to the brake light. Twist the bulb holder and replace the bulb.
Then replace the carpet panels using the fastners.

Nov 09, 2009 | 1987 Toyota MR2

1 Answer

How to remove door panel on 2002 dodge caravan


The easiest way is to purchase a door panel removal tool for less than $10. You'll still probably break a couple of the tabs but the job will be much easier. Here's a picture of one:

http://www.bodyshopzone.com/archives/trim/door_panels/Dodge/stratus_2003/dpdsta31a.jpg

Sep 29, 2009 | 2002 Dodge Caravan

2 Answers

Remove F150 door panel


There isn't a diagram to show you EXACTLY where each fastner is but this tool pictured below will help you remove the trim panel from the door. Go slow and try to get right under the plastic fastner.

5228ddc.jpg

Jul 23, 2009 | 2005 Ford F-150

2 Answers

1999 GMC Suburban - how to install dr side power window motor/arm


The window should be put in a closed position.
Hidden screws behind buttons of the same color as panel should be opened up using a pick or small screwdiver.
Pry the lower part of the panel away from the door using a paint scraper, The lower half of this panel is usually held in with plastic fastners. When pulled hard enough they will release. These fastners are replacable you can buy them at your local body shop. After releasing all plastic fastners lift door panel off door lock in an upward thrust. Be careful not to pull to far away from door due to wire harnesses and speaker wires ect.. These can be uncliped to remkove whole panel. To operate window you can replug window harness wires in order to bring the window into the proper position to remove bolts that hold it into place. Carefully position glass in upward position and duct tape in place.
The regulator is held in place by three or more bolts.
Remove regulator.
Compare your new part to the existing window regulator.
Installation is reversal of removal.
Any questions get back!

Jan 17, 2009 | 1999 GMC Suburban

1 Answer

Remove hood insulator blanket


carefully pry the black plastic fastners holding blanket away from hood. these fastners snap into a bracket attached to the hood replace by inserting into the original hole

Dec 30, 2008 | 2004 Cadillac SRX

Not finding what you are looking for?
2009 Dodge Journey Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...