Question about 2004 Ford Taurus

1 Answer

Wires to brake light switch broken. - 2004 Ford Taurus

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

Thats common, you can buy a new "pigtail" from Ford or a Motorcraft dealer.

Posted on Jan 04, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1999 chevy tahoe. Is there a way to adjust brake light switch. Lights come on when manually press / move switch. But won't come with brake pedal

Brake light switch is activated by brake pedal arm, above the pedal. Have you looked to see if the switch is bent, broken, out of place or disconnected from wires?

Apr 23, 2017 | Cars & Trucks

1 Answer

Brake light switch wires broken

Here is a picture of the brake light switch. Also at this point just buy a new connector and splice it on, much easier.

Jan 15, 2012 | 2000 GMC Sierra 3500

1 Answer

Running , signal & hazard lights work but the brake lights dont .

check the fuses then if they are good check the brake light switch on the base of the brake pedal.there should be a switch with 2 wires on wire should have 12 volts at all times and the other should have 12 volts only when the brake pedal is pressed.if not then the switch is no good and needs replacing.also check and make sure the wires are not broken for the switch(common problem).

Apr 27, 2011 | 2004 Ford Mustang

1 Answer

I changed all the bulbs and the fuse in my 94 Camry but the tail lights still do not light up. The brake lights and marker lights are okay. What else can I do?

Its most likely that your brake switch is broken. Look under the dash by the steering column. Run your hand up the brake pedal arm and you will feel a tab that makes the brake lights go on. The tab pushes on the switch to shut off the lights. You will find that the switch is broken, stuck in, or that the wires have come loose from the switch. Good luck...

Dec 06, 2010 | 1997 Toyota Camry

2 Answers

Brake lights dont work

Check the brake light switch, it is down on the brake pedal lever, you can dis-connect the wire connector at the brake light switch and check for broken wires at the connector, and then jumper the connector with a paper clip, if the brake lights come on then replace your brake light switch.

There might be more than one switch attached to the brake light pedal lever, the brake light switch usually only has two wires going to it when there are two switches.

If there is no problem with the brake light switch then you can suspect the turn-signal switch to be at fault, as all of the running lights, turn-signals, brake lights, and hazard lights are all ran through the turn-signal switch. You can also try stepping on the brake pedal and wiggle around the turn-signal switch and see if the brake lights flicker or come on.

Apr 26, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Cannot get shifter out of park without using screw driver

I have found broken wires right at the connector on the brake light switch. That switch does a lot more than just activate the brake lights, it also releases the shifter interlock solenoid, and that is why you have to press the brake pedal to shift out of park. (there may be two switches attached your brake pedal lever, if so then check both wire connectors carefully for broken wires).

Apr 20, 2010 | 2001 Nissan Pathfinder

2 Answers

96 suburban brake ligh don't work

you may have to change the brake light switch at the top of the brake pedal stop by your local GM dealership in the parts department and they be able to print you off pictures and diagrams but check on the part at your local part store because it maybe cheaper wish you the best of luck Michigan Man.

Dec 27, 2009 | 1996 Chevrolet Suburban

2 Answers

I replaced all rear bulbs and i still have no lights when i hit the brakes

If they work when the turn signals or the hazards are on then you need to replace the brake light switch on the brake pedal bracket.If the lights don,t work on hazards but do with the turn signals,then you have a fuse blown.If none of the above work then you need to check the wiring under the truck box for a bad plug in connection,corrosion or broken wires.

Dec 23, 2009 | Chevrolet 1500 Cars & Trucks

1 Answer

Brake lights dont work

Look for broken wires or with a test light. follow the wires checking from the fuse box back to the brake lights checking every so often in between the light wires and the fuse box.

Dec 06, 2008 | 2002 Jeep Liberty

Not finding what you are looking for?
2004 Ford Taurus Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides