Question about 1992 Honda Accord

1 Answer

What size socket for drive shaft nut - 1992 Honda Accord

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Honda Master
  • 1,455 Answers

It's either a 32mm or a 36mm socket for the CV shaft nut.

Posted on Jan 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Universal joint replacement


first remove drive shaft most likely to be 10mm bolts. if a vise is available use it to press out the old joint after removing keepers with snap ring pliers.if no vise is present use an old socket and hammer to remove joint.

Mar 21, 2012 | 1999 GMC Yukon

2 Answers

Rear axle leaks, want to replace seal where drive shaft connects to axle.


A continental is a front wheel drive car since 89. You must mean a town car. The pinion shaft seal is tricky because of a bearing preload issue that can be catastrofic if you get it wrong. I would recomend seeking the skills of a pro.

Jan 16, 2011 | 1997 Lincoln Continental

1 Answer

How to replace the center support bearing and what size bolts or if studs are used what size nuts are required? Also what is the best tool to use for changing the spark plug behind the steering shaft?


The center support bearing is secured to the cross-member using either a stud with an 11/16 in. nut or sometimes an 18mm nut. or it can also be sucured using a 3/8 in. bolt with a 5/8 in. bolt head and either a 15mm, 5/8", 11/16", or an 18mm nut, and GM did not stop the assembly line when they ran out of a certain nut or bolt and that is why there could be so many different ones used.

(A split drive-shaft is a balanced unit and it must be marked for proper alignment before separating the two halves or the drive shaft will no longer be in balance and will cause a vibration and early u-joint failure, and be very sure that there is a line on each half of the drive-shaft before it is separated so that the drive-shaft can be aligned re-assembled correctly)

The center support bearing should be pressed off and on the drive shaft using a hydraulic press, (a machine shop usually does not charge very much to do that) and using a hammer and a drift to replace the center support bearing is not recommended however some people do replace the center support bearing that way and a lot of the time they will damage the drive shaft or center support bearing and that will only make it more difficult and time consuming to properly install the center support bearing.

(The u-joint and the axle yoke should also be marked together before the u-joint is removed from the axle yoke so that they are installed back in the same way that they came out to prevent any drive shaft vibration)

To change the spark plug behind the steering shaft use a spark plug socket (a good spark plug socket will also have a provision for attaching a 5/8" or 16mm wrench to the end of the spark plug socket) and instead of putting an extension and a ratchet on the socket, slip the socket onto the spark plug and then use the wrench to loosen the spark plug and to tighten it, but also use a length of 3/8" fuel line and push the end of the spark plug into the fuel line and then use it to start and run down the spark plugs and also to remove the spark plugs once they have been loosened.


e223c4e.jpg

Sep 12, 2010 | 1996 GMC Sonoma

1 Answer

What size socket do i need to take the nut off of the cv shaft to replace my wheel bearing


Most likely 36mm. You have to measure nut and convert to mm. Size, divided by .0395

Feb 13, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

Shadtree replacement of a front wheel bearing possible?


the nut is special its metric, the parts store will know its like a 30or35. i know an inch and a half socket is to small If you got the tool i see no problem. you may have to tap on it a little but it should come right out.

Feb 03, 2009 | 1986 Dodge Lancer

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...