Question about 1992 Buick Park Avenue

1 Answer

How do you remove the front brake calipers to replace the brake pads? I don't find any bolts or pins to remove that hold the calipers in place

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 3,113 Answers

Remove bolts from the back of it.

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the front breaks on a 1992 ford f250 custom??


take off the wheels one or two at a time,un-pin the middle swivel device that the rim slides over,if there is none then just pull the rim off.Now on the caliper is a retractable pin that is triangle shaped about 3-4 inches long.This pin is what holds the caliper and the pad together!Also dont forget to remove the bolts that hold the calipers in place!Now you should be good,whatever you do,don't remove the brake lines!Good luck,hope this helps!-CB

Dec 20, 2011 | 1992 Ford F250

1 Answer

How to replace front discs and pads


Front brakes are very simple to do:
  • Pull off the front tires.
  • Remove the brake pads by removing the slide pin bolts where the piston assembly attaches to the caliper mounting bracket. The slide pin bolts are usually a 12 or 14mm bolt. Once the piston assembly is free slide the old brake pads out.
  • Compress the piston back into the caliper by using a large pair of channel lock pliers or a c-clamp. If you don't do this, you won't be able to get the new pads on.
  • Before you put the new pads on, replace the rotor.
  • Remove the two bolts for the caliper mounting bracket. They are in the back and are bigger than the slide pin bolts. Usually a 17 or 19mm bolt.
  • Pull off the caliper mounting bracket.
  • At this point the old rotor should slide right off. If it doesn't slide right off, look for a screw in the center of the rotor, some cars will have a screw there to hold the rotor on. If there's no screw and it still won't come off, try tapping it with a hammer. If you're replacing the rotor, don't be shy.
  • Put the new rotor on. Make sure to clean off any grease with brake cleaner that may be on the braking surface from packaging.
  • Put the caliper mounting bracket back on.
  • Put the new brake pads on. Make sure to use some anti-squeal grease on the back of the pads.
  • Put the caliper assembly back on with the slide pins. Grease up the slide pins as well.
  • Put the wheels back on.
  • Make sure to pump your brakes 10 - 15 times before you drive off. Because you compressed the piston back into the caliper, the piston will not be contacting the brake pads unless you pump the brakes.

Good Luck!
~Brandon

May 27, 2011 | 2002 Mitsubishi Lancer

1 Answer

How can i change the brake pads on the rear tires??


Hi. Please see procedure below:

Remove the old Brake Pads

1 Park your car on a level surface. If you have a stick shift car make sure the car is in gear. Place blocks in front of the front tires so the car does not move while you are working on it.

2 Open the hood of your car and locate the master cylinder. If necessary, remove brake fluid until the level in the container is less than half full. A turkey baster is a good tool for this. Put the brake fluid in the plastic container and dispose of it the way you dispose of motor oil.

3 Raise the rear end of your car with your car jack. Remove the rear tire or wheel assembly.

4 Remove the parking brake cable from the back of the caliper. Use the pliers to remove the cable clip (restraining clip). This step is done only for Grand Prix RPO Z7Us.

5 Hand-tighten two lug nuts to the studs to hold the disc rotor in place while you work on the caliper. Remove the bolt and washer holding the cable support bracket to the caliper. The cable support has the parking brake cable and brake hose attached to it. This step is not done for Grand Prix RPO Z7Us.

6 Use the socket wrench to remove the caliper guide pin bolts. Slide the caliper off of the disc rotor and hang it in the wheel well with a small bungee cord or wire hanger; Don't let the caliper hang from the brake hose.

7 Remove the brake pads and shims from the caliper. Throw away the shims.

Install the new Brake Pads

1 Use the spanner tool to rotate the piston clockwise all the way into the caliper. Make sure the notches on the piston are at the 6 and 12 o'clock positions. There is a boot (rubber seal) around the piston bore. Lift the seal's inner edge and press out any trapped air. Insert the brake pad clips into the caliper support.

2 Apply a thin coat of lubricant to the parts of the inner pad that come in contact with the caliper piston and mounting areas. As you install the brake pads in the caliper support, make sure the wear sensors are downward and at the leading edge of the rotor when the tire rotates. Push the brake pads into the support, holding the metal shoe edge against the spring end of the pad clips. This slightly bends the spring ends and lets the notches engage with the support. This step does not apply for the Grand Prix RPO Z7U.

3 Swing the caliper back into place over the brake pads and replace the mounting bolt. Reconnect the cable support bracket and tighten the bolt to 32-ft.lb. (43 Nm). Remove the lug nuts holding the rotor in place. For the Grand Prix RPO Z7U, Slide the caliper back into place on the disc rotor. Reconnect the parking brake cable. Insert and tighten the caliper mounting bolts to 44 foot lb. (60 Nm).

4 Replace the tire wheel assembly. Lower the car to the ground.

5 Pump the brake pedal a few times to seat the brake pads. Do this before trying to move your car.

6 Add fluid to the master cylinder container to replace any you removed before you removed the old brake pads.

7 Season the brake pads by making only gentle stops when you are driving for the first week

Thanks!

Apr 29, 2011 | 2006 Pontiac Grand Prix

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

Will I need a caliper reset tool kit to change the brakes on my 2007 toyota sienna or will a standard c-clamp do the job? And since it is an ABS system, I assume that brakes must be bled, correct?


Brake Pads Removal & Installation Front To Remove:
  1. Remove the front wheels. Front brake caliper (exploded view) toyota-09-00-5838.gif

  2. Loosen the caliper bleeder.
  3. Hold the slide pin; remove the 2 mounting bolts and remove the brake caliper from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, wear indicators and anti squeal shims.
  8. Remove the slide pins and bushings from the caliper support.
To Install:
  1. Lubricate the slide pins and bushings with brake grease.
  2. Install the bushing on the slide pin.
  3. Install the slide pin on the caliper support.
  4. Install the brake pad support plates on the caliper supports.
  5. Lubricate the anti squeal shims with brake grease.
  6. Install the anti squeal shims on the brake pads.
  7. Install the pad wear indicator facing upward and install the pads on the caliper support.
  8. Install the caliper on the support.
  9. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  10. Fill the reservoir and bleed the brakes.
  11. Install the front wheels.
Rear To Remove:
  1. Remove the rear wheels.
  2. Loosen the caliper bleeder. Rear brake caliper (exploded view) toyota-09-00-5842.gif

  3. Hold the slide pin; remove the 2 mounting bolts and rear brake caliper assembly from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, and anti squeal shims.
  8. Remove the slide pins from the caliper support.
To Install:
  1. Lubricate the slide pins with brake grease.
  2. Install the slide pin on the caliper support.
  3. Install the brake pad support plates on the caliper supports.
  4. Lubricate the anti squeal shims with brake grease.
  5. Install the anti squeal shims on the brake pads.
  6. Install the rear pads on the caliper support.
  7. Install the rear caliper on the support.
  8. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  9. Fill the reservoir and bleed the brakes.
  10. Install the front wheels.
prev.gif next.gif

Sep 18, 2010 | 2007 Toyota Sienna

1 Answer

How to change front brake pads on 2006 town and country


Loosen tire lug nuts. Jack up the car and remove lug nuts and tire. Remove two bolts holding the caliper in place. Remove the the two bolts holding pads in place. Hang caliper with a wire from wheel so brake line is not stressed. Mount new calipers in correctly and tigthen pad bolts. Put caliper on and tighten caliper bolts. Replace tire and lugs nuts. Jack car down and tigheten lug nuts.

Aug 17, 2010 | 2006 Chrysler Town & Country

1 Answer

Brake pad replacement 2004 audi a4 and rotor how do i do and what tools are neccessary?


YOU NEED REMOVE A LITTLE BRAKE FLUID FROM MASTER CYLINDER.THEN YOU RAISE VECHICLE SAFELY.SUPPORT IT WITH JACK STAND.MAKE SURE VECHICLE IS ON LEVEL SOLID GROUND.REMOVE TIRE OR WHEEL.THEN YOU NEED A LARGE C - CLAMP.PLACE C - CLAMP OVER BRAKE CALIPER AND BRAKE SHOE BACKING.TIGHTEN C - CLAMP JUST ENOUGH PUSH CALIPER PISTON BACK IN CYLINDER BORE TO REMOVE CALIPERS FROM ROTORS.TO REMOVE BRAKE CALIPER YOU NEED 2 OPEN AND BOX END WRENCHES ONE TO HOLD CALIPER SLIDE PINS AND THE OTHER WRENCH FOR LOOSEN CALIPER BOLTS.THEN YOU REMOVE CALIPER AND REPLACE FRONT BRAKE SHOES.IF YOU NEED TO REMOVE BRAKE ROTORS JUST REMOVE THE BRAKE CALIPER CARRIER SUPPORT BOLTS THE REMOVE THE BRAKE CALIPER CARRIER SUPPORT THEN REMOVE ROTOR.YOU NEED TO REPLACE BOLTS WITH NEWS AND USE LOCK TIGHT.THEN YOU PUT IN NEW BRAKE PADS IN CALIPER PUT CALIPER BACK ON SUPPORT CARRIER.REPLACE WITH NEW BOLTS USE LOCK TIGHT THEN TORQUE BOLTS TO 26 FT LBS.MAKE SURE MASTER CYLINDER COVER IN PLACE.WHEN YOU FINISH REPLACING BOTH FRONT BRAKE PADS PUMP BRAKE PEDAL TO SEAT BRAKE SHOES AGAINST BRAKE ROTORS SO YOU WILL HAVE FIRM BRAKES WHEN YOU APPLY THEM. THEN CHECK YOUR BRAKE FLUID LEVEL IN MASTER CYLINDER MAKE SURE ITS NOT LOW. MAKE SURE YOU HAVE FIRM BRAKES BEFORE DRIVING.IF YOU HAVE ANY PROBLEMS CHANGING FRONT BRAKE PADS YOU CAN GO TO ANY AUTO PARTS STORE AND BUY A HAYNES REPAIR MANUAL.

Jun 16, 2010 | 2004 Audi A4

1 Answer

Brake pad replacement


Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Front wheels
  3. Place a C-clamp over the caliper as illustrated, place a screw drive head against the outboard pad and hook against the rear of the caliper. Slowly tighten the screw drive and retract the caliper pistons into their bores and breaking the outboard brake pad from the caliper fingers.
  4. Once the pad is free, slide the caliper in on the guides to provide clearance between the rotor and inboard pad.
  5. Place an appropriate prytool through the center opening in the top of the caliper behind the inboard pad between the pistons using care not to contact the piston boots. Pry the pad to free it from the pistons.
  6. Remove the two caliper guide pin bolts and position the caliper aside. Remove the brake pads.
ff17c9d.gif
Place a C-clamp over the caliper as illustrated

b802acb.gif
View of the caliper guide pins and boots (1), anti-rattle clips (2), brake rotor (3), outboard pad (4), caliper adapter (5) and inboard pad (6)

To install:
  1. Completely compress the caliper pistons
  2. Install or connect the following:
    • Brake pads with anti-rattle clips onto the adapter
    • Caliper and align the guide pin bolt holes with the guide pins. Install the pin bolts and tighten to 32 ft. lbs. (43 Nm).
    • Banjo bolt with new washers on each side of the hose fitting and tighten to 35 ft. lbs. (47 Nm)
    • Wheels
    • Negative battery cable
  3. Check and adjust the brake system fluid level and road test the vehicle.

Nov 01, 2009 | 2005 Chrysler Pacifica

1 Answer

How do i replace front pads on 2005 chrysler pacifica


PLEASE DON'T FORGET TO RATE!!!!

Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Front wheels
  3. Place a C-clamp over the caliper as illustrated, place a screw drive head against the outboard pad and hook against the rear of the caliper. Slowly tighten the screw drive and retract the caliper pistons into their bores and breaking the outboard brake pad from the caliper fingers.
  4. Once the pad is free, slide the caliper in on the guides to provide clearance between the rotor and inboard pad.
  5. Place an appropriate prytool through the center opening in the top of the caliper behind the inboard pad between the pistons using care not to contact the piston boots. Pry the pad to free it from the pistons.
  6. Remove the two caliper guide pin bolts and position the caliper aside. Remove the brake pads.
24539c8.gif
Place a C-clamp over the caliper as illustrated

6ccd8b6.gif
View of the caliper guide pins and boots (1), anti-rattle clips (2), brake rotor (3), outboard pad (4), caliper adapter (5) and inboard pad (6)

To install:
  1. Completely compress the caliper pistons
  2. Install or connect the following:
    • Brake pads with anti-rattle clips onto the adapter
    • Caliper and align the guide pin bolt holes with the guide pins. Install the pin bolts and tighten to 32 ft. lbs. (43 Nm).
    • Banjo bolt with new washers on each side of the hose fitting and tighten to 35 ft. lbs. (47 Nm)
    • Wheels
    • Negative battery cable
  3. Check and adjust the brake system fluid level and road test the vehicle.

Nov 01, 2009 | 2005 Chrysler Pacifica

1 Answer

How to replace the front brake pads


    Calipers With Guide Pins
  1. Step 1 Disconnect the negative battery cable from the battery. Remove the wheel. Using an open wrench hold the lower guide pin. Remove the bolt that secures the caliper.
  2. Step 2 Pivot the caliper up and then suspend it from the frame using mechanic's wire. To remove the pads, slide the pads straight out.
  3. Step 3 Using a C-clamp, compress the caliper piston into the bore. Insert the new pads by removing the mechanics wire and pivoting the caliper back into it's place.
  4. Step 4 Clean the old bolt and apply thread locking compound. If the old bolt can not be used install a new bolt. Hold the guide pin using a back-up wrench when tightening the bolt. Using a torque wrench, torque the bolt to 26 foot/pounds. Install the wheels. Add oil to the master cylinder reservoir. Reconnect the negative battery cable to the battery.
    Calipers With Sleeves and Bushings
  5. Step 1 Disconnect the negative battery cable from the battery. Remove the wheel. Remove the bolt that secures the caliper to the carrier.
  6. Step 2 Push the caliper up and pivot the caliper bottom out of the carrier. Remove the pads and the anti-rattle springs.
  7. Step 3 Install the new pads by putting the anti-squeal pads onto the caliper and then sliding the new pads onto the carrier. Put the caliper top back into place. Remove the mechanics wire and push the caliper up so that it pivots back into place and the bottom.
  8. Step 4 Clean the caliper mounting bolts. Install the caliper mounting bolts and using a torque wrench, torque the bolts to 18 foot/pounds. Install the wheel. Add oil to the master cylinder reservoir. Reconnect the negative battery cable to the battery.

Jul 09, 2009 | 2006 Volkswagen Jetta

Not finding what you are looking for?
1992 Buick Park Avenue Logo

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...