Question about 1988 Ford Bronco II

1 Answer

Cylanoid just replaced tostarter .now no power

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,114 Answers

Start by checking your positive battery cable connection that the batter and the solenoid remove those cables with the proper sized wrench and clean with wire brush or sandpaper reconnect and attempt to start and be sure all the other wires wired to the soleniod ignition wire for one is connected and secure.

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a question about my 2003 gmc seirra 6.0l. When I turn the key to crank the engine it struggles for a second then starts. It has the same sound as if the battery is almost dead, but I just replaced...


Might be a fuel delivery issue. You can rent a fuel pressure test kit from most parts stores. see if the pump pressures are correct or if the regulator is bad.

Nov 01, 2013 | GMC Safari Cars & Trucks

1 Answer

1966 ford pickup f-100 352 motor will not start


check wire goes from ignition to starter if no power when trying to crank then replace the wire with a new one its easier ok

Nov 12, 2012 | Cars & Trucks

1 Answer

1996 nissan maxima is eating cylanoid switches


If "tapping" the SOLENOID ever worked... you
HAVE A DEFECTIVE SOLENOID.

Defective is all inclusive... and when "STUFF"
happens (burns up)... it is VERY LIKELY to cause
COLATERAL damage...

(FRIED WIRES & IGNITION SWITCH)
((fix that "STUFF" later)).

At the SOLENOID ... apply "B" battery DIRECTLY
to the "S" terminal of the SOLENOID...

IF it does not fully spin up the starter 100% of the time
the solenoid or the starter is DEFECTIVE.

Apr 14, 2017 | 1996 Nissan Maxima

1 Answer

Starter cylanoid just replaced,now no power to anything


You might have not hooked up the main hot wire right. It is a large cable that goes from the battery to the solenoid. Make sure all connections on the battery are tight and clean.

Jan 03, 2011 | Ford Bronco II Cars & Trucks

1 Answer

I go to crank the truck and it keeps blowing the cylanoid fuse and i have replaced the bat, and the cylanoid switch on the fire wall. what can be causing this problem?


what have you found out about the problem ,seems strange to have a solonoid on the firewall because this system was only used on 70s vehicles since then pre -engaged starters have been used ..just cant seem to get my head around the layout of this truck ,never seen one here in spain ,anyway happy and a prosperous new year

Jan 01, 2010 | Ford F-150 Cars & Trucks

2 Answers

No electric power, only to feed side of cylanoid


There is a fuseable link on the heavy wire, not the battery cable, going to the hot terminal of the solenoid. That heavy wire (about 12 gauge) supplies power to the vehicle. Take a test light and probe the wire on both sides of that fuseable link (it says fuseable link on it). If you don't have power on the vehicle side of that link, that's part of the problem. Now you have to figure out why it blew. It may have just corroded off, I've seen that happen.

Dec 03, 2009 | 1987 Ford Ranger

1 Answer

'91 Toyota Truck Starts Randomly.


try to replace the starter or at least the cylanoid because the points in the cylanoid tend to rust over time and not work this should fix ur problem

Dec 05, 2008 | 1991 Toyota Pickup

1 Answer

My 1990 Thunderbird is getting no electrical power. The battery is new and fully charged. I have put in a new ignition switch and cylanoid switch. Still nothing. No headlights, no hazzard lights or dummy...


Replace the ignition switch. It's under the steering column covers half way down the column. There is a long electrical plug that has a bolt in the center of it that holds it on. You may need to buy tamper proof sockets to actually remove the switch. They look like torx bits but has a hole in the center of it.

Jul 22, 2008 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...