Question about Jeep Grand Cherokee

1 Answer

P0441 evap emission control system purge flow fault i am trying to find the repair for this code

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 95 Answers

There is a selonoid in the engine compartment has a hose going to it that hose goes to a tank in the rear of the truck near the gas tank if the hose is broken cracked or un plugged . did you just get gas ? what year is the truck is it v8 or 6 cyl let me know

Posted on Jan 03, 2011

×

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

keithheavili
  • 410 Answers

SOURCE: im getting a P0441 EVAP emission control system

Here is what I could find for your code error as potential causes:
After market parts and accessories nonconforming to the EVAP system specifications.
Damaged, missing or improperly installed fuel filler cap.
Blockage in fuel vapor hoses/tubes (EVAP canister tube, EVAP canister purge outlet tube or EVAP return tube) in EVAP system.
Disconnected or cracked fuel vapor hoses/tubes in EVAP system.
EVAP canister purge valve stuck closed.
Canister vent (CV) solenoid stuck open.
Fuel tank pressure (FTP) sensor malfunction.
EVAP canister leaking.
Fuel vapor control valve tube assembly blocked.
Fuel vapor vent valve assembly blocked.

Obviously the gas cap would be the easiest and cheapest thing to fix.  Just make sure it is put on correctly and tight.  If it is not that, I would have to suggest to take it to a mechanic because the other problems on that list are not really DIY material.  Hopefully it is the gas cap and you can take care of it yourself.  Good luck.

Posted on May 17, 2009

  • 71 Answers

SOURCE: P0441 EVAP Control System Incorrect Purge Flow

Test the purge valve and the vent valve for leaks. This can only be done with a Tech 2 and or a vacuum pump.

Posted on Jun 21, 2009

  • 1 Answer

SOURCE: Check Engine light - Code P0441 (Evap Emission

There is an evap purge valve located in the back of the driver side of the engine. This valve needs to be replaced. Had the same code a couple weeks ago. Replaced that valve and the problem was fixed. Hope this helps.

Posted on Dec 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0441 what dose it mean and how can I fix it .toyota camery le 1998model


P0441 1998 Toyota Camry - Evaporative Emission Control System Incorrect Purge Flow

When is the code detected? Pressure in charcoal canister and fuel tank does not drop during purge control (2 trip detection logic).

Possible symptoms: - Engine Light ON (or Service Engine Soon Warning Light)
- Possible a noticeable fuel odor caused by the release of fuel vapors

P0441 1998 Toyota Camry Description: The Engine Control Module (ECM) tests the Evaporative Emission (EVAP) system for the following conditions:
- Large and small leaks

- Excess vacuum

- Purge flow during non-commanded conditions

- Fuel Level and Fuel Pressure sensor faults

- EVAP Purge and Vent Valve faults

The ECM monitors the Fuel Tank Pressure sensor in order to determine the level of vacuum/pressure in the EVAP system. The ECM commands both the EVAP Purge Solenoid and the EVAP Vent Valve ON when the conditions are met in order to apply an engine vacuum to the EVAP system. The ECM commands the EVAP Purge Solenoid OFF once the system has reached a predetermined level of vacuum. This test verifies if a vacuum can be achieved in the EVAP system. Failure to develop a vacuum may be caused by a large leak or a restriction.

P0441 1998 Toyota Camry Evaporative Emission Control System Incorrect...

Possible causes - Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- Incorrect fuel tank vacuum relief valve
P0441 Toyota Evaporative Emission Control System Incorrect Purge Flow

Jun 01, 2015 | 1998 Toyota Camry

1 Answer

Emissions Code


Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
- Purge control VSV connector disconnected.
- Evaporative Emission (EVAP) Canister Purge Regulator Valve is faulty/jammed.
- Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
- Evaporative Emission (EVAP) Canister Sealing faulty.
- Pipes between Tank Breathing and Throttle Body leaky/blocked.
- Hose connection(s).
- Intake leak.
Solutions:
- Check Evaporative Emission (EVAP) Canister Purge Regulator Valve.
- Perform Output Test.
- Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
- Check Evaporative Emission (EVAP) Canister.
- Perform Basic Setting.
- Check Pipes between Tank Breathing and Throttle Body.

Jan 10, 2014 | Toyota Cars & Trucks

1 Answer

Toyota echo won't start code 440 441 446


Error Code: P0440
Fault Location:
Evaporative Emission (EVAP) System - Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Soution:
Check Evaporative Emission (EVAP) System Sealing.
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .

Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve .
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.

Error Code: P0446
Fault Location:
Evaporative Emission (EVAP) System, Vent Control - Circuit Malfunction
Possible Cause:
Wiring harness.
Evaporative emission (EVAP) canister purge valve.
Engine control module (ECM).

Feb 25, 2013 | 2002 Toyota ECHO

2 Answers

Common causes for codes p0441


getting code p441 could be caused by evap purge solenoid vacuum line loose leaking or restricted, evap purge solenoid faulty, evap purge vacuum line to canister leaking or disconnected,evap canister failed.

Feb 06, 2012 | 2001 Chrysler 300M

1 Answer

1996 pontiac firebird 5.7 liter engine light on po1441


Two choice dudes code there...

DTC P0441 - Evaporative Emission (EVAP) Control System Incorrect Purge Flow
EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.
With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Common Chrysler fix - Replace Leak Detection Pump / LDP
  • Repair damaged EVAP lines or canister
  • Repair open or short in voltage feed circuit to Purge Solenoid
  • Repair open in PCM purge command circuit
  • Replace purge Solenoid
  • Replace vacuum switch
  • Repair restriction in Evap line or canister or soleniod
  • Repair resistance in purge connector
  • Replace PCM


DTC P1441 - Evaporative Emission (EVAP) System Flow During Non-Purge.
M
ost generally caused by a purge valve stuck open. the only way to diag for sure is with a gm tech 2 scan tool and a smoke machine. but if dont mind spending a few bucks as a good quess. Replace the purge valve.


Hope this helps.

Jul 28, 2011 | 1996 Pontiac Firebird

1 Answer

1996 saab 900s p0441 evaporative emission system incorrect purge flow


This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.

Causes: A code P0441 could mean one or more of the following has happened:
* Bad vacuum switch
* Broken or damaged EVAP line or canister
* Open in PCM purge command circuit
* Open or short in Voltage feed circuit to Purge Solenoid
* Faulty purge solenoid
* Restriction in EVAP solenoid, line or canister
* Corrosion or resistance in purge connector
* Bad PCM

Possible Solutions: With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
* Common Chrysler fix - Replace Leak Detection Pump / LDP
* Repair damaged EVAP lines or canister
* Repair open or short in voltage feed circuit to Purge Solenoid
* Repair open in PCM purge command circuit
* Replace purge Solenoid
* Replace vacuum switch
* Repair restriction in Evap line or canister or soleniod
* Repair resistance in purge connector
* Replace PCM

Test it and tel us news.

Jan 11, 2011 | 1996 Saab 900

1 Answer

Hav Check eng. Light Code PO 441 what could be the problem?


P0441 Evaporative Emission Control System Incorrect Purge Flow

This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tankmag-glass_10x10.gif into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.
FB.init("dd7d9e9681341cde77587bc6a2029f6f");OBD-Codes.com on Facebook Symptoms

Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light.
Causes

A code P0441 could mean one or more of the following has happened:

  • Bad vacuum switch
  • Broken or damaged EVAP line or canister
  • Open in PCM purge command circuit
  • Open or short in Voltage feed circuit to Purge Solenoid
  • Faulty purge solenoid
  • Restriction in EVAP solenoid, line or canister
  • Corrosion or resistance in purge connector
  • Bad PCM
Possible Solutions

With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

  • Common Chrysler fix - Replace Leak Detection Pump / LDP
  • Repair damaged EVAP lines or canister
  • Repair open or short in voltage feed circuit to Purge Solenoid
  • Repair open in PCM purge command circuit
  • Replace purge Solenoid
  • Replace vacuum switch
  • Repair restriction in Evap line or canister or soleniod
  • Repair resistance in purge connector
  • Replace PCM

Sep 22, 2010 | Volkswagen Passat Cars & Trucks

1 Answer

I have a toyota matrix w/ 88,000 miles 2006. I have the check engine light on, took it to advance auto, codes are PO441- EVAP control system , purge flow-fault also PO455 EVAP system-large leak I don't...


P0441 Evaporative Emission Control System Incorrect Purge Flow
OBD-II Trouble Code Technical Description

Evaporative Emission Control System Incorrect Purge Flow
What does that mean?

This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.
Symptoms

Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light.
Causes

A code P0441 could mean one or more of the following has happened:

* Bad vacuum switch
* Broken or damaged EVAP line or canister
* Open in PCM purge command circuit
* Open or short in Voltage feed circuit to Purge Solenoid
* Faulty purge solenoid
* Restriction in EVAP solenoid, line or canister
* Corrosion or resistance in purge connector
* Bad PCM

Possible Solutions

With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

* Common Chrysler fix - Replace Leak Detection Pump / LDP
* Repair damaged EVAP lines or canister
* Repair open or short in voltage feed circuit to Purge Solenoid
* Repair open in PCM purge command circuit
* Replace purge Solenoid
* Replace vacuum switch
* Repair restriction in Evap line or canister or soleniod
* Repair resistance in purge connector
* Replace PCM
THIS IS LIKELY FROM TOPPING OFF THE TANK EACH TIME YOU FUEL UP



P0455 is similar:

Technical Description

Evaporative Emission Control System Leak Detected (no purge flow or large leak)
What does that mean?

This indicates a fuel vapor leak or lack of purge flow in the EVAP control system. It means a large leak has been detected. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.
Symptoms

You likely won't notice any drivability problems.
Causes

A code p0455 most likely means one or more of the following has happened:

* A loose or improperly affixed gas cap
* A non-conforming gas cap (i.e. not factory/original brand)
* Other leak or damaged piece in EVAP system

Possible Solutions

With a p0455, the most common repair is to:

* Remove and reinstall the gas cap, have AutoZone clear the codes, and drive for a day and see if the codes come back.
* Otherwise, replace the gas cap, and/or
* Inspect the EVAP system for cuts/holes in tubes/hoses (you may hear a vacuum noise or smell fuel), repair if necessary

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 05, 2010 | 2006 Toyota Matrix

1 Answer

P0441


DTC P0441 - Evaporative Emission Control System Incorrect Purge Flow

What does that mean?
This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle's fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine.

EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 is set.

Symptoms
Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light.

Causes
A code P0441 could mean one or more of the following has happened:
* Bad vacuum switch
* Broken or damaged EVAP line or canister
* Open in PCM purge command circuit
* Open or short in Voltage feed circuit to Purge Solenoid
* Faulty purge solenoid
* Restriction in EVAP solenoid, line or canister
* Corrosion or resistance in purge connector
* Bad PCM

Possible Solutions
With a P0441 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:

* Common Chrysler fix - Replace Leak Detection Pump / LDP
* Repair damaged EVAP lines or canister
* Repair open or short in voltage feed circuit to Purge Solenoid
* Repair open in PCM purge command circuit
* Replace purge Solenoid
* Replace vacuum switch
* Repair restriction in Evap line or canister or soleniod
* Repair resistance in purge connector
* Replace PCM

Other EVAP DTCs: P0440 - P0441 - P0442 - P0443 - P0446 - P0453 - P0455 - P0456

Hope helps.

Jun 18, 2010 | Hyundai Motor 2002 Elantra

2 Answers

P0441 EVAP Control System Incorrect Purge Flow


Error Code: P0441
Fault Location:
Evaporative Emission (EVAP) System - Incorrect Flow Detected
Possible Cause:
Malfunction Indicator Lamp (MIL) active.
Evaporative Emission (EVAP) Canister Purge Regulator Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Purge Solenoid Valve faulty/jammed.
Evaporative Emission (EVAP) Canister Sealing faulty.
Pipes between Tank Breathing and Throttle Body leaky/blocked.
Hose connection(s).
Intake leak.
Possible Solutions:
Check Evaporative Emission (EVAP) Canister Purge Regulator Valve .
Perform Output Test.
Check Evaporative Emission (EVAP) Canister Purge Solenoid Valve.
Check Evaporative Emission (EVAP) Canister.
Perform Basic Setting.
Check Pipes between Tank Breathing and Throttle Body.
VSV connector near air filter box disconnected.

Jun 15, 2009 | 1996 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

255 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...