Question about 1994 Mitsubishi Mirage

1 Answer

Trying to find the engine size to replace a rear main seal and don't have the owners manual

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 22,219 Answers

Take it out then go to the auto factor with it in your hand ,cannot possibly go wrong then can you

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear seal leaking on 2007 ford escape


In order to replace the rear main seal you will need some auto repair tools and experience . this is a big job , the transmission must be removed to replace this seal, also make sure that the seal is the leak,

oil always flows down, a leak on the top of the engine will flow down and drip at the center rear and look like a rear main seal , make sure that is the leak!!.

Depending on what engine you have and if it has 4 wheel drive the time for a shop to do is from 7 to 10 hours depending on engine size and 4wd,

Oct 21, 2012 | 2007 Ford Escape

1 Answer

I have a 93 grand Jeep Cherokee Laradeo ,to change the oil pan seal , and or the oil filter housing to change the O rings , or the timing cover seal or the rear seal , dose one need too lift up or pull...


The oil filter housing and the timing cover can all be worked on with engine in car.
For the rear engine seal (rear main seal), the transfer case and transmission will have to be removed to access the seal.
Most of the time, the oil pan can be removed without raising the engine. Check your clearance under there for anything obstructing removal. (I loaned out my Jeep manual and never got it back!) On some cars, engine needs to be raised about 4 inches for pan to clear the oil pickup tube. Don't know about your Jeep.

Nov 07, 2011 | 1993 Jeep Grand Cherokee

1 Answer

Rear barring an seal replaced


I'm not sure if this is the right part of your car but, are you talking about the rear seal on the engine for the crankshaft?

If so:

Rear Main Oil Seal REMOVAL & INSTALLATION Fig. 1: Rear main seal installation for the 2.3L and 2.5L engines 85553306.gif
Fig. 2: Removing the rear main seal 85553307.gif
Fig. 3: Installing the rear main seal on the 2.9L engines 85553308.gif
If the crankshaft rear oil seal replacement is the only operation being performed, it can be done in the vehicle as detailed in the following procedure. If the oil seal is being replaced in conjunction with a rear main bearing replacement, the engine must be removed from the vehicle and installed on a work stand.
  1. Remove the starter.
  2. Remove the transmission from the vehicle, following the procedures in Section 7.
  3. On a manual shift transmission, remove the pressure plate and cover assembly and the clutch disc following the procedure in Section 7.
  4. Remove the flywheel attaching bolts and remove the flywheel and engine rear cover plate.
  5. Use an awl to punch two holes in the crankshaft rear oil seal. Punch the holes on opposite sides of the crankshaft and just above the bearing cap to cylinder block split line. Install a sheet metal screw in each hole. Use two large screwdrivers or small pry bars and pry against both screws at the same time to remove the crankshaft rear oil seal. It may be necessary to place small blocks of wood against the cylinder block to provide a fulcrum point for the pry bars. Use caution throughout this procedure to avoid scratching or otherwise damaging the crankshaft oil seal surface. To install:
  6. Clean the oil seal recess in the cylinder block and main bearing cap.
  7. Clean, inspect and polish the rear oil seal rubbing surface on the crankshaft. Coat a new oil seal and the crankshaft with a light film of engine oil. Start the seal in the recess with the seal lip facing forward and install it with a seal driver. Keep the tool, T82L-6701-A (4-cyl. engines) or T72C-6165 (6-cyl. engine) straight with the centerline of the crankshaft and install the seal until the tool contacts the cylinder block surface. Remove the tool and inspect the seal to be sure it was not damaged during installation.
  8. Install the engine rear cover plate. Position the flywheel on the crankshaft flange. Coat the threads of the flywheel attaching bolts with oil-resistant sealer and install the bolts. Tighten the bolts in sequence across from each other to the specifications listed in the torque chart in this section.
  9. On a manual shift transmission, install the clutch disc and the pressure plate assembly following the procedure in Section 7.
  10. Install the transmission, following the procedure in Section 7.
prev.gif next.gif

Oct 07, 2010 | 1994 Ford Explorer Limited

1 Answer

My car has a worn out engine rear seal how can I replace it?


This is a fun one. You can do this 2 different ways. One of which, remove the transmission and flexplate (automatic trans.) or flywheel (manual trans.) and you can loosen the rear main cap and pull the old rear main seal out and install the new one. The other way of replacing it is removing the engine and replacing the seal on an engine stand. Either way, it'll take some time to do.

Apr 04, 2010 | 1994 Ford Ranger Supercab

1 Answer

2000 Nissan Maxima Se with a manual transmission 135K miles original owner. Rear engine seal leaking. Mechanic has suggested that since he has to separate the engine and the transmission he should replace...


You should not have to replace the master or slave cylinder with a rear main seal but if the clutch has alot of miles on it you should have that done with the seal because you will be paying for almost all of the labor with the seal.

Jan 23, 2010 | 2000 Nissan Maxima

1 Answer

My 1994 camaro w/ 3.4L engine has an oil leak in rear of engine. It is running down both sides of the block in rear. Oil filter is wet, but not leaking, the starter and bell housing drip oil and its...


This is most likely a leak from your rear main seal. It happens and can be a pain to replace if you're a DYI kinda person without the nec. equipment.
  1. Raise and safely support the vehicle with jackstands.
  2. Remove the transmission.
  3. If equipped with a manual transmission, remove the clutch and pressure plate.
  4. Remove the flywheel assembly.
  5. Using a suitable prytool, carefully pry the old seal out.
6. Inspect the crankshaft for nicks or burrs, correct as required.
88143g59.gif Crankshaft rear main seal - 5.7L engine

To install:
  1. Clean the area and coat the seal with engine oil. Install the seal onto tool J-34686 for 3.4L engines, J 41349 for 3.8L engines or J 35621 for 5.7L engines.
  2. Install the tool (with the seal mounted to it) onto the rear of the crankshaft. Tighten the screws snugly to be sure the seal will be installed squarely over the crankshaft.
88143g60.gif Exploded view of the rear main seal installation - 3.4L engine
Click to Enlarge

  1. Tighten the wing nut on the installation tool until it bottoms out.
  2. Remove the tool from the crankshaft or rear oil seal housing, as applicable.
88143g61.gif Rear main seal and installation tool - 3.8L engine
Click to Enlarge
88143g62.gif After position the seal on the tool, install it to the crankshaft housing

  1. Install the flywheel.
  2. If equipped with a manual transmission, install the clutch and pressure plate.
  3. Install the transmission.
  4. Check the fluid levels, start the engine and check for leaks.

Dec 30, 2009 | 1995 Chevrolet Camaro

1 Answer

Engine main seals leaking


Replace them.

You will need to diagnose exactly which seals are leaking.

Replacing the front main seal requires removal of the cam timing components, including the timing belt and lower timing cog. The front main engine seal is installed in the oil pump, and can be removed with a pick. The new seal should be installed with care, using ether a seal installer tool or a socket/pipe of size equal to the metal ring in the seal, using a gentle tapping with a small hammer or board to ensure that you don't damage the seal. You must also ensure that the seal is seated fully in the bore. Ensure that you install the seal in the correct orientation.

If the rear main seal needs to be replaced, you will need to remove the engine or transmission from the vehicle to access it.

Dec 19, 2009 | 1989 Honda Civic

2 Answers

Rear main seal is leaking on a Ford Mustang 2003 V-6


In order to replace the rear main seal u have to pull the transmission out to access it, u will need a special seal installer tool to install the new rear main "full circle seal", it u don't use the special ford tool the seal will leak again, also if there is a groove worn ion the crankshaft the crank must be repaired or replaced or the or the seal will leak again, so this is avery diff job, a 9 on the scale of 1-10 with 10 being the mos difficult.

May 10, 2009 | 2003 Ford Mustang

1 Answer

Rear main seal leaks..does this affect transmission??


A leaking rear main seal will not cause your transmission to leak.

The transmission has its own seal and should not leak because of the engine rear main seal.

Due to the labor involved in replacing the rear main seal on the engine, it is best if you replace the front transmission seal at the same time if possible.

Installation varies on different vehicles but the principles are the same.

Apr 15, 2009 | 1997 Oldsmobile Regency

Not finding what you are looking for?
1994 Mitsubishi Mirage Logo

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...