Question about 1991 Dodge Dynasty

1 Answer

How do i relive the fuel pressure on the line to replace the fuel filter

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 59 Answers

There is usually a schrader valve in the fuel rail with a plastic cap on it.

Posted on Jan 03, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where's my gas filter for 2006 Chrysler pacifica


okay you have to crawl under the vehicle. ( or put the back end up on ramps or on jack stands). Looking on the right side ( passenger side ) follow the fuel lines from the fuel tank and you will find the fuel filter there. I know there are no manuels for this vehicle since it was only built from 2004-2008. It is a cylinder and it will be very dirty. make sure you relive the pressure from the system ( take off the gas cap and disconnect the negative cable from the battery) it is an easy replacement.

Oct 11, 2015 | Chrysler Cars & Trucks

1 Answer

'01 Punto Leaking Fuel


If you can access the lines and filter it wont be that hard, but you may need to buy special disconnect tools. Make sure you relive the fuel pressure before disconnecting anything.

Oct 14, 2012 | 2001 Fiat Stilo 1.2

1 Answer

How to change a fuel pressure regulater do i have to pull fuel rail


You should not have to pull the fuel rail to remove the fuel pressure regulator. Just remove the vacuum lines, and the bolts. Make sure to relive fuel pressure before removing the fuel pressure regulator. To relive the fuel pressure, remove the fuel pump fuse or relay, and start the engine. This will relive the fuel pressure.

Jun 17, 2011 | 1994 Pontiac Grand Am

2 Answers

Where do you relieve the fuel pressure at when changing the fuel filter on a 1996 Plymouth Voyager with a 3.3L engine (short wheel base)


there is no pressure regulator only one is built into the fuel tank to relive the pressure look on fuel rail for a small valve looks like a valve stem similar to tires stem it as a black plastic cover unscrew that and push with a pointy object

Aug 28, 2010 | 1996 Plymouth Voyager

1 Answer

Where is the fuel filter for 04 range rover located victor


Hi. The filter will be mounted underneath the vehicle. you will need to raise the vehicle, and support it carefully. Once raised, you will be able to locate the filter. It will be just to the right or left side of the fuel tank, mounted on a bracket, in between the fuel line. be sure to disconnect the negative battery post cable, and relive the fuel pressure, before removing the fuel lines form the filter.

Click here to view a picture of your filter.


Dec 04, 2009 | 2004 Land Rover Discovery

1 Answer

How do i change the fuel pump on a 1994 mitsubishi galant?


there should be an access panel either underneith the rear seat or in the trunk that should give access to the pump it self but before u start rippin and tearin u need to relive the fuel system of pressure what u can do is pull the fuel pump relay start the car and let it run out of fuel. the relay is prob in the fuse panel on the drivers side. dont quote me on that though. make sure u replace the fuel strainer in the tank and the fuel filter in line to the engine and put the new unit in reverse of dissasembly.

Oct 22, 2009 | 2000 Mitsubishi Galant

2 Answers

Where is the fuel filter located on a 2002 Lincoln LS, V8 and how do you reduce the pressure on the fuel line in order to safely remove and replace fuel filter.


To relive the fuel pressure look under hood on drivers side front of engine locate the fuel line where it goes into the fuel rail,trace it back a little ways and you will see a schrader valve for checking fuel pressure. Remove the plastic cap and take something like a small screw driver and press the pin in center to release pressure.
To replace fuel filter you have to remove left front wheel and inner plastic fender panel and fuel filter is located behind this at the back area.

Jun 04, 2009 | 2000 Lincoln LS

4 Answers

Fuel filter


unbolt the filter from the bracket, that is a 5/16" machine screw head size, then remove the nylon clips that hold the lines onto the filter, hold a rag over the fuel line when u remove it, it will have about 30 pounds of pressure.

May 09, 2009 | Ford F-150 Cars & Trucks

1 Answer

Fuel filter replacement


look over rear end it is by the gas tank .you need to spray the fittings with wd40 or P B blaster it works alot better than wd40 to help loosen the fittings start by pulling fuel relay under hood in fuse box start car this will relive fuel pressure you will need 2-15mm line wrenchs for one end of filter the other you squeeze the fitting and pull out filter

Nov 08, 2008 | 2000 Cadillac DeVille

2 Answers

Fuel filter location and replacement


You need to first jack the car off the ground, the fuel filter is located in front of the fuel tank. A new fuel filter is inexpensive and easy to find. One end of the filter needs to be disconnected with a wrench, around 5/8". The other end is a very simple, somewhat fragile plastic clip that should be no problem to disconnect once you look at it for a minute or so. Make sure and keep lots of rags handy, because once you unhook the filter, it will leak all over the place. Once you have the old one out, installing the new one will be simple.

May 15, 2008 | 2001 Oldsmobile Alero

Not finding what you are looking for?
1991 Dodge Dynasty Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...