Question about Mitsubishi Montero

2 Answers

How do I tell weither the crank shaft pulley is a sensor type or non sensor typ. 1996 V26 Engine 4M40 2.8 turbo diesel

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 38 Answers

Easy answer. When you look down from the top of the engine, there will be a small wiring loom that runs down the timing cover and enters very near the bottom. From memory it a two wire sensor. If this is the case u have a sensor type crankshaft pully.

Posted on Jan 04, 2011

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My is Fernando I have a 1989 park avenue buick,my car doesn't start about 3 months ago i replaced the main pulley because was making a loud clicking noises, the computer is reading bad sensor but do i have to remove the all pulley assambly or there is any other and easy solution.

Posted on Oct 09, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crank sensor located in an 89 Dodge Daytona


The info I looked at was for 2.5L engine, non-turbo.
If you have distributor, you don't have one. You may have a sensor inside distributor. Because the distributor usually works off the cam shaft, they don't call it a crank sensor.
Now, if you have a coil pack, you do have a crank sensor, some I've seen are on the tranny bell-housing. Or at the cranks shaft pulley in the front.
I did look at online partsbook for the engine I listed, no crank sensor listed.

Mar 14, 2016 | Dodge Daytona Cars & Trucks

1 Answer

Need torque settings for mazda xa 3.0l diesel 4 cyl


con rod bolt tension is 55-60ft/lbs
crank shaft main bearings is 80-85 ft/lbs
fly wheel bolts95-100 ft/lbs
crank shaft pulley nut 94-123 ft/lb
head studs tension 80-95 ft/lbs working in a spiral direction from no 1 stud directly in the centre of the head. Pull down in 10ft/lb increment starting at 20 ft/lbs
valve clearance is .010" both valves cold but after warming engine and re-tensioning the head studs re set valves to .012 both valves
injector retaining nuts tension12-17 ft/lbs

Dec 25, 2013 | Saab 9 Cars & Trucks

1 Answer

1996 Sonoma where's the crank shaft sensor


The crank sensor bolts into the front timing cover right underneath the crank pulley. If you look at the vehicle from underneath, you'll be able to see it... very common failure

Feb 03, 2013 | 1996 GMC Sonoma

2 Answers

Head Bolt torque settings for a 3.1 bighorn turbo Deisel


What is the torque for the crank pulley for 3.1turbo

Dec 21, 2010 | 1996 Isuzu Trooper

1 Answer

Were is the cam shaft senor and the crank shaft senor located


this car does not have a camshaft sensor the distributor pick up coil acts as a cam sensor here is crank sensor info the crank sensor is located in front of engine just behind the crankshaft pulley using ohmmeter check resistance between terminals on sensor replace is not within specs cold 1630-2740 ohms hot 2065-3225 ohms if this is not the problem please reply to your post ill monitor it. hope this helps

Jul 26, 2010 | 1996 Toyota Corolla

2 Answers

My toyota 3C turbo diesel engine the turbo compressor is flooding of oil . I can.t trace where it is coming from That is why I am searching service manual for this turbo charger. 12ct


Hi,

If your turbo housing is getting flooded with oil the it can only come from the shaft seal on the inside of the turbo.

You will need to remove it and replace the shaft seal.

Jun 19, 2010 | Cars & Trucks

1 Answer

1996 crank shaft postion sensor for a 3.0 lumina located where?


CHEVY 3.1 ENGINE CRANK SHAFT SENSOR IS BEHIND CRANKSHAFT PULLEY.

Sep 29, 2009 | Chevrolet Lumina Cars & Trucks

1 Answer

2002 Expedition Crank Shaft Sensor


FRONT OF THE ENGINE ABOVE THE CRANK PULLEY

Jul 06, 2009 | 2002 Ford Expedition

3 Answers

Charging problem on 1996 Dodge Ram 3500 Cummins Turbo Diesel


I had the same problem on a 94 dodge with the cummins. It seems the crank sensor that reads from a notch on the harmonic balancer was the problem Without this sensor reading that the engine is running the alternator wont charge. Possibly the same problem with yours

Mar 25, 2009 | 1996 Dodge Ram 3500 Club Cab

2 Answers

TIMING MARKS CAMBELT REPLACEMENT FOR CL-T CHARADE, PLEASE


This is the best I could find for you .. I am unfortunately able to verify the info because I have no personal experience with this car or its engine ...

Mar 14, 2009 | 1988 Daihatsu Charade

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...