Question about Chevrolet Avalanche

2 Answers

I was able to start, open and lock my vehicle with just a quick push on the designated remote key pad buttons, now I have to press and hold several times to get the transmitter to work. I thought the batteries were low, so I took it to Canadian Tire and have them installed new batteries and it still doesn't work

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,033 Answers

You may need to open the pad up and clean the contacts on the small board. When you state you have to press or hold several times, it sounds like it works when contact is made inside the pad. I use something like a baby wipe or a clean up wipe but nothing with harsh chemicals to avoid messing up the board.

Posted on Jan 03, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 22,246 Answers

Dealer only to programme ,diagnostic equipment only

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to find out where the valet/override button is located on my car....trying to program a new keyless remote


1. Insert key into the ignition and turn it to the On or ACC position, turn off radio. (do not start the vehicle)

2.Press and hold DISP button on radio until settings is displayed.

3. Press Seek until FOB PROG is displayed .

4. Press Prev or Next and BEGIN will be displayed

5. Press DISP and programming will begin when PUSH FOB is displayed. Press and hold Lock and Unlock together until vehicle chimes. This will signal successful programming. May have to hold buttons up to 20 seconds. Hold Lock and Unlock on additional remote until vehicle chimes again.

6. Exit programming mode. Scroll to Exit and press DISP to exit programming.

If you don't have the original radio, it can be done with a scanner.

Mar 19, 2016 | 2004 Chevrolet Chevrolet Impala

1 Answer

My 2004 Town and country van had to be jump started and now key fob won't lock or unlock doors.Took key fob to locksmith he said key fob was working, van was not reading signal and he didn't know what


The fob may need to be reprommed to the car. Do the following:

Grab your working remote. Push the LOCK button five times, allowing exactly two seconds to pass between each press of the LOCK button. Insert the ignition key and turn it to RUN. Push and hold UNLOCK on the working remote for 6 seconds. Push and hold PANIC for one second while continuing to hold UNLOCK. Release both buttons at the same time.
Push any button on the remote to program it. Then push any button on the remote that was already programmed. It has to be reprogrammed. The remote is now programmed to the vehicle. Turn the key to OFF.

Oct 28, 2014 | Cars & Trucks

2 Answers

I have a 2007 chevy tahoe with factory installed auto start. what buttons on remote or what sequence do i push to get truck running?There is a lock button an unlock button a rear glass open button and a...


To get your truck running with auto start first press the lock button and then hold down the semi cicle button for about 3-5 seconds this will start your truck

Jan 28, 2011 | 2007 Chevrolet Tahoe

1 Answer

I just got a used car. it came with the original key pad to the car, and a remote start key pad. no books on how to use it. i dont know what buttons to push on either pads to use my remote start. any...


Assuming that the car actually has remote start circuitry (probably does if the remote you have has the actual button for it), and also assuming that the radio DIC has remote start ENABLED, here is how you start it . . . press and release the LOCK button, then press and hold the Start (top) button for like 1-2 seconds and the car should start OR the lights will flash.

Nov 10, 2010 | 2005 Pontiac G6

1 Answer

Step by step reset the door remote control lexus 400LS


1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

Jun 16, 2009 | 1996 Lexus LS 400

1 Answer

Un work of the doors auto control lexus


1. sitting in driver seat, with driver's door OPEN, press lock/unlock button ON THE DRIVERS DOOR to lock all doors, then manually unlock driver door only.
2. Insert YOUR key in ignition, DO NOT TURN, then remove key.
3. Using the same lock/unlock button ON THE DRIVERS DOOR, slowly press lock-unlock in 5 cycles
4. Shut door.
5. Open door.
6. Using the same lock/unlock button ON THE DRIVERS DOOR, again slowly press lock-unlock in 5 cycles
7. With the door open insert your key into the ignition, turn to 'on' position (DON'T START), wait 5 seconds. Turn off and remove key.
8. Locks should cycle once (Car will lock and then unlock once by herself). If they don't cycle or they cycle more than once, do steps 1-7 over.
9. Now using the remote, push lock button, hold for one second, then release the button. The locks should cycle once. If not, start over and go slower.
10. Close the door.
11. Open the door.
12. Press the lock button on the remote. The locks should do a lock-unlock cycle.
13. Close the door
14. Press the lock button on the remote, the doors should lock.
15. Press unlock button and the doors should unlock.

Long beep to follow if successful.

Jun 16, 2009 | 1996 Lexus LS 400

1 Answer

Need the steps to programme the remote


Remote Programming Instructions

1. Driver's door OPEN and unlocked, all other doors closed and locked.

2. Insert YOUR key in ignition, DO NOT TURN, remove key.

3. Using the MANUAL lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

4. Shut door.

5. Open door.

6. Using the lock/unlock button ON THE DRIVERS DOOR, slowly press lock and unlock 5 times (count the lock 5 times and unlock 5 times).

7. With the door open insert your key into the ignition, turn to on position (DON'T START), wait 5 seconds. Turn off and remove key.

8. Locks should cycle once (Car will lock and then unlock once). If they don't cycle or they cycle more than once, do steps 1-7 over.

9. Now using the remote, push lock button, hold for one second,
release. The locks should cycle once. If not, start over and go slower.

10. Close the door. Open the door. Press the lock button on the remote. The locks should cycle. Close the door. Press the lock button on the remote, the doors should lock. Press again and the doors should unlock.

Jun 02, 2009 | 1995 Lexus LS 400

1 Answer

BMW Keyless Entry not working


hi, to program the keys to the vehicle is quite simple

1) open the vehicle, sit inside and close the door

2) insert the key in the ignition and turn to position 1 so that just the air bag light illuminates

3) press and hold the unlock button on the key and remove the key from the ignition (do not release the unlock button)

4) while still holding the unlock button with the key removed press the lock button 3 times

5) release the unlock button on the remote and the door locks should lock and unlock if the proceedure has been carried out correctly

6) to program any other key(s) press and hold the unlock button on remote and again press the lock button 3 times but do not insert it into the ignition or turn the ignition on as done previous.

you may want to print these instructions and read them a few times before proceeding, if you muck up the process while programing keys, no harm will be done, you just have to start the process over. hope this is of some help, regards mark.

Apr 07, 2009 | 1998 BMW 5 Series

2 Answers

Keys won,t lock or unlock doors


Use this Procedure for Buick Vehicles "With" Driver Information Center Buttons.

This information is in your "Owners Manual" in the "Drivers Information Center Section."

1. Insert Key and turn to ON position so you can access Driver Information Center.

2. Press the vehicle information button until PRESS TO RELEARN REMOTE KEY displays.

3. Press the set/reset button until REMOTE KEY LEARNING ACTIVE displays.

4. Press and hold the lock and unlock buttons on the key-less remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.

5. To program additional remotes at this time repeat step 4. This vehicle can have a maximum of eight remotes programmed.

6. To exit programming mode turn key off and remove key. Test remote(s).


Use this Procedure for Buick Vehicles "Without" Drivers Information Center Buttons.

To access this display, the vehicle must be in Park (P) with key in the on position (as far as you can go without cranking engine).

1. Press the trip odometer reset stem until RELEARN REMOTE KEY displays.

2. Press and hold the trip odometer reset stem for three seconds. The message REMOTE KEY LEARNING ACTIVE will display

3. Press and hold the lock and unlock buttons on the first key-less remote at the same
time for approximately 15 seconds. A chime will sound indicating that the remote is
programmed.

4. To program additional remotes at this time repeat step 3. This vehicle can have a maximum of eight remotes programmed.

5. To exit programming mode turn key off and remove key. Test remote(s).

Good Luck !

Mar 25, 2009 | 2005 Buick LaCrosse

2 Answers

How to program the key for my bmw 750i model 1997 to lock/unlock the door


BMW 7-Series - Key Remote Programming
Three methods to try:
Method 1:
1. Working from within the vehicle and with the doors shut
2. Turn ignition to position 1 and back to off within 5 seconds.
3. Remove the key from ignition and press and hold the unlock button for 15 seconds during this time press the key lock button 3 times within 5 seconds.
4. Release both buttons.
5. Doors will lock and unlock to show correct programming has occurred.

Method 2:
To do this procedure you need to have one working key and one key that needs to be programmed.
1) Get in and close all doors.
2) Turn on the ignition and turn off quickly. (No more than 5 seconds) to start the process. Next action must take place within 30 seconds.
3) Remove the 1st key.
4) Hold the key up near your left shoulder (this is so it is closer to the remote receiver antenna.
5) Hold down the unlock button and press the lock button 3 times. Release the unlock button and the doors lock which confirms the operation.
6) Quickly repeat steps 4 & 5 for key #2 etc.
If it does not work, try doing the keys in opposite order. Key 2 then key 1, vs 1 then 2.

Method 3:
Alternate if you do not have a working remote
1. Turn key to position 1 five times very quickly 2. Remove key 3. Hold unlock button then press lock button 3 times, release unlock button.
4. If you have another key do the same button pressing within 30 seconds 5. Turn on ignition to finalise.
PLEASE NOTE: This programming procedure programs the remote control part of the key. Any transponder chip for the immobiliser (starting of car) will not be programmed and must be done by a specialist.
window.google_render_ad();

Dec 16, 2008 | BMW 750 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6910 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...