Question about 2004 Ford F150

Open Question

What is torque spec on 4wd 05 f150 spindle nut

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
polarcycle
  • 1392 Answers

SOURCE: torque specs for front spindle (nut hold brake drum in place)

Tighten till the wheel bearing is tight. No one really uses a specification for that, do it by feel. when the nut is tight, and there is no play in the bearing. Should be about 15-20 ft/lbs, with about .001-.003 end play if you need exact numbers though.

Posted on May 30, 2009

Ad
c17hydro
  • 2984 Answers

SOURCE: is there a torque spec on the spindle nut for the

  1. nstall the caliper mounting bolts. Perform the following procedure before installing the caliper guide pin bolts (15 Series only).
  2. Remove all traces of the original adhesive patch.
  • Clean the threads of the bolt with brake parts cleaner or the equivalent and allow to dry.
  • Apply Red Loctite#272 to the threads of the bolt.
  1. Install the caliper mounting bolts (25 series). Tighten the caliper guide pin bolts to 42 Nm (31 ft. lbs.) on the 15 series; 108 Nm (80 ft. lbs.) on the 25 series.

Posted on Nov 19, 2009

Testimonial: "thank you that was very helpful"

  • 599 Answers

SOURCE: torque specs on replacing cv axle on 05 Pacifica

ok here we go tie rod=55 ft lbs axel nut= 180 ft lbs strut bolts= 65 ft lbs plus 90 degrees

Posted on Jan 07, 2010

Testimonial: "thank you very much!!!!!!!!!!"

emissionwiz
  • 76846 Answers

SOURCE: spindle nut torque spec on a 2004 F-150

u DON'T torque this!! tighten the nut while spinng the rotor, then back off untiol it is free, then tighten it down until it seats tight, then turn another 1/8" tighter, that is it, any tighter u burn up the the wheel bearings

Posted on Feb 04, 2010

emissionwiz
  • 76846 Answers

SOURCE: WAT IS THE TORQUE SPECS ON THE FRONT SPINDLE NUT

U DON'T TOQUE A SPINDLE NUT!!! JUST TIGHTEN WITH PLIERS AND INSTALL COTTER PIN.

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is an 01 dodge dakota 4wd spindle nut torque specs


180 ft lbs. Make sure to re-install the locking cap and cotter pin after torquing it down.

Jul 02, 2014 | 2001 Dodge Dakota

2 Answers

I need the torque specs for a 6 cyl 2004 Dodge Dakota 2 wheel drive- front wheel hub. In inch-lbs if possible.


Spindle nut. Tighten the nut to 185 ft. lbs. (251 Nm). Inch pounds is not an option, this critical torque spec is FT lbs.

Apr 26, 2011 | 2004 Dodge Dakota

1 Answer

How to change front hub assembly on 05 mustang


Remove tire/wheel. (5 nuts)
Seperate the brake pads just a little; pry apart with a screw driver. Easier to remove and replace later.
Remove caliper/brake assembly (2 bolts). Do NOT remove brake line.
Remove brake rotor (there may be a retainer clip or two that needs to be removed and discarded.
Remove black center cap (after reading warning on the cap).
Remove large spindle nut.
Slide bearing/hub assembly off the spindle. (If stuck, you may have to tap it with a hammer. It's a straight smooth shaft.

Reassemble in reverse order.
Tighten the nut to the correct torque spec. I don't know what it is, but it's pretty high... 200ft-lbs? The torque is important because it sets the preload on the bearing balls and races. Too low or torque will cause early bearing failure.

Bearing/hub looks like this:
$(kgrhqf,!hue1e+wrmfcbnhq(o4kj!~~_12.jpg

Apr 09, 2011 | Ford Mustang Cars & Trucks

1 Answer

What is the torque for a 2004 F150 spindle nut?


The axle nut torque is:
296 ft-lbs for 2WD
and
20 ft-lbs for 4WD

Make sure you use the correct torque for your application!

Aug 29, 2010 | 2004 Ford F150

1 Answer

WAT IS THE TORQUE SPECS ON THE FRONT SPINDLE NUT ON A 2004 FORD F150 XLT!?


U DON'T TOQUE A SPINDLE NUT!!! JUST TIGHTEN WITH PLIERS AND INSTALL COTTER PIN.

Mar 09, 2010 | 2004 Ford F150

1 Answer

Spindle nut torque spec on a 2004 F-150


u DON'T torque this!! tighten the nut while spinng the rotor, then back off untiol it is free, then tighten it down until it seats tight, then turn another 1/8" tighter, that is it, any tighter u burn up the the wheel bearings

Feb 04, 2010 | Ford F-150 Cars & Trucks

1 Answer

1986 ford f150 front axle


I believe its 50 ft/lbs for the nut and the lock nut. If you're talking about a 4x4, if it's a 2wd and you mean the spindle nut, then I'll have to get back to you. Cheers.

Feb 03, 2009 | 1986 Ford F150 SuperCab

Not finding what you are looking for?
2004 Ford F150 Logo

Related Topics:

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...