Question about 2005 Hyundai Elantra

3 Answers

I changed my cluch and now my car will not start

Posted by on

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 146 Answers

Please check engine start fuse
and battery lif
and might might some of cable not fixed well

Posted on Jan 03, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 376 Answers

Remember all the (ground) cables you removed to accheive this, make sure the starter is getting power with the key, of all electrical is ok, then make sure the clutch disenguages correctly. but it sounds like you missed some ground mounts.

Posted on Jan 03, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 22,265 Answers

Who forgot to refit the crank sensor ,its on the bellhousing

Posted on Jan 03, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whats wronge when you can change gears without use of cluch with no grinding or movement


Either the clutch is totally gone (or the disc broke)or the transmission
input shaft broke.

Apr 20, 2013 | 1996 Saturn SW

3 Answers

When I press the clutch in my 99 Rodeo, there is this horrible noise. What is the problem?


if the noise is only there when you push down the clutch, you need to replace the throw out bearing.

Apr 02, 2011 | Isuzu Rodeo Cars & Trucks

1 Answer

We just bought a 2000 Suzuki esteem, the problem is whenever we start the car, it becomes very difficult to shift between gears when the car is idle, but when the car is on the freeway, shifting works...


The cluch not fully disingaging , ( carpet under the pedel, pedel bent , bushing worn out of pedal, low on fluild in clutch master ( brake fluid ) and bad cluch master or slave or air in system. A damaged clutch will drag too. If it shifts OK with the car shut off standing still trans lube is likly OK too. If it has a clutch cable it may need to be adjusted pull up on the clutch pedal as high as it can go then pust down with your hand it should only go down an inch before it gets harder to pust down as it openes the clutch and shoul continue to go down about 4 or more inches. The pedal should be as high or a little higher than the break paedal. If not the pedal height may be needing to be adjusted higher. Some slave master hydrolic sysems aren't adjusted and have to be replaced to fix lack of enought movement Clutes that are hard to pust in or get much harder as you get closer to the floor the cluch is likly to be worn out and need to be changed with a new clutch kit and resurface the flywheel. The flywheel can change to unflatand the cluch can drag. engine oil getting into the clutch though a leak in the valve cover or rear main can get on the cluch and make it drag and grab.

Mar 21, 2010 | 1996 Suzuki Esteem

1 Answer

2002 hyundai accent my cluch peddel goes soft


check fluid level if low bleed out the system.If thats fine then you have slave cylinder Problem.Before Changing the cluch assembly check your master cylinder is pushing good pressure.

Jul 17, 2009 | 1998 Hyundai Tiburon

1 Answer

1997 Cutlass Supreme Oldsmobile, 3.1:air conditioner is brocken.


Try adding a can of freon, you might have a leak, the clutch will not work if not enough pressure in ac system

May 23, 2009 | 1997 Oldsmobile Cutlass Supreme

1 Answer

Cluch is slipping after changing it


everytime you change a clutch, it is good practice to change the pressure plate also. in this case, thats what I would do.

Mar 27, 2009 | 1994 Volkswagen Golf

1 Answer

Ford focus hatchback 2004 turbo diesl


1000 pounds sounds a bit rich, just4 parts. sounds like you needto shop around,if you get someone to fix it look at the clutch plate or pressure plate you might be able to re use them, to save money . you should get about 135 kms out of of a clutch

Jan 06, 2009 | 2003 Ford Focus

2 Answers

1992 Ford Ranger - Starts Sometimes.. New Clutch. Help?


take back to dealer and have them check the neutral safety switch on the clutch because if the switch is not adjusted properly you will have this problem

Jan 01, 2009 | 1992 Ford Ranger

1 Answer

Cluch won't dis engage


How long have you had your car? How many miles on it?

Maybe the clutch plate gone, if the plate is not thick enough, you won't change the gear.

Jul 06, 2008 | Mazda MX-5 Miata Cars & Trucks

Not finding what you are looking for?
2005 Hyundai Elantra Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...