Question about Mitsubishi Galant

1 Answer

Crank Shaft Position Censor for Mitsubichi Galant 2003 went bad. How much for a new one

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 17,970 Answers

This replacement part is around US$ 50.00; check the right part in THIS LINK

Hope helps.

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor located on a 2003 Mitsubishi Galant 4 cylinder


Hello, crank position sensor located at the 2 o`clock position hidden behind timing cover and crank shaft pulley. If you look closely in well lit area or use a flashlight you can follow the (CCPS) harness down the right hand side of timing cover to where it goes into lower timing cover on lower right hand side of crank shaft pulley. It can be replaced with out removing timing belt. Please note if the 60,000 miles heavy service interval for timing belt is needed and water pump condition should be observed when repairing the crank position sensor.

Feb 21, 2018 | 2003 Mitsubishi Galant

1 Answer

How can I iinstall a tachometer sensor a mitsubichi galant 03.


This depends on the tach you buy some have there own sensors and others use the ones with the car you can get a signal from the crank shaft sensor

May 09, 2014 | Cars & Trucks

1 Answer

L have a 2003 Kia Sorento, sometimes it will just turn over but won,t crank. after a while it will start up. or l can be driving down the road and it will start poping and cut off, and won,t start.it does...


It will be a position sensor problem Check the air gap and check that the censor rotor is tight and that there is no material getting in the air gap causing a problem

Jan 06, 2014 | Kia Cars & Trucks

1 Answer

2003 Dodge Caravan sxt


Is the check engine light on ?

Aug 06, 2012 | 2003 Dodge Caravan

1 Answer

I am working on a 2003 mitsubishi galant and the timing belt was destroyed along with the crankshaft position sensor, balancer belt and the crankshaft sensor plate, now i have replace them and algined all...


Check to see if your getting voltage to your coil wire plug coming from vehicle, if there voltage at the plug then its most likely that when the crank shaft censor was damaged it may have shorted out your cam shaft sensor because they both run off the same system..

Jul 18, 2011 | 2003 Mitsubishi Galant

1 Answer

I have a 99 jeep Cherokee and it gets very hot often. i have 3 elect fans in it (2 that **** in, 1 that blows through). i do not run a thermostat for max water flow, i added a new radiator (The Heat...


I think you may be on the right track. If the timing is too far advanced, the engine can overheat. The computer uses the crank sensor input to time the engine. Let us know if it still over heats with the new crank sensor in.

Sep 12, 2010 | 2004 Jeep Grand Cherokee

1 Answer

2003 ford F250 6.0 deisel..it will crank but will not start,cam and crank wil not synchronize..both are new. oil gauge wil not show pressure while cranking RPM.is around 48 rpms on a scan tool...


I HAVE A 7.3 DEISEL AND I DONT KNOW IF THE 6.0 HAS ONE OR NOT BUT MY CRANK SHAFT SENSOR WENT BAD AND THE TRUCK WOULD NOT START( JUST TURN OVER ) DEALER PUT NEW CRANK SHAFT SENSOR ON MINE AND FIXED THE PROBLEM...HOPE THIS HELPS...

Nov 29, 2009 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

Plenty of battery power,engine turns,will not start


the best thing to do is have the cpu read for any fult codes it could be some thing like the crank shaft censor playing up or the cam shaft censor but the problem is in the cpu

Nov 15, 2009 | 2003 Dodge Dakota Club Cab

1 Answer

Cranks but wont turn over


you know. i took it to a mechanic and actually.... The timing belt cut the Crank Shaft Censor... So it was the crank shaft censor again. The wires were routed wrong from the first mechanic that "fixed" the car.

Aug 01, 2008 | 2000 Hyundai Sonata

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

79123 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...