Question about 2003 Mercury Grand Marquis

1 Answer

Reverse lights and licsene plate lights not working

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 679 Answers

Check the sockets for corrosion, power, ground
Check the wiring for an open
Run a test wire from the reverse lights to the plate lights.
thanks

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 nissan sentra (released in the phils) reverse or back lights dont work..This car has 4 reverse lights. Left, right and two in the middle (near the plate number).When i put the car in reverse, only the...


sounds like you have a bad ground wire or the wire going to the sides is broken. you may have to check the connections till you find where the wires are connected. if you can test the two side lights with a battery to confirm they do work and are not bad bulbs. or switch them with working light bulbs to confirm they work. then if they work they you need to start looking for a section of wire that may be broken or is corroded and will need to reconnected to make work again.

Sep 17, 2017 | 2001 Nissan Sentra

1 Answer

I had my slave cylinder and clutch plate replaced. they also replaced the driver side cv axle and now the ABS and ESP/BAS and TCS lights are on. oh and my reverse lights don't turn on. Is there an


ABS problem may be related to the axle work...either a sensor was left unplugged, got damaged or is obstructed by rust. Reverse lights are on a separate system and likely, they weren't working and you just noticed. I'd have the shop that did the work check it over. If for any reason you don't want them doing that, have another shop do that and document what they found.

Mar 12, 2013 | 2007 Jeep Compass 2.4

1 Answer

Running lights for 2005 odyssey on license plate are not working


The lenses cover & the lenses housing snap in to place. There are plastic tabs on the sides of each.
Directions: Remove the license plate light housing, and disconnect the 2P connector from the light. Remove the lens from the light, and then replace the bulb. Install the light in the reverse order of removal.

Nov 05, 2012 | Cars & Trucks

1 Answer

License plate light and reverse lights dont work after checking lights and fuse


They are two different circuits. Do you have voltage at the neutral safety switch when in reverse ? Are the ground wires for the light sockets ok ?

Aug 05, 2012 | 2001 Buick Century

1 Answer

Back up lights and license plate light doesn't work.


Reverse lights are activated by a small switch on the transmission. Usually located on the passenger side of the vehicle with a small rubber cap over the switch, Your plate light bulbs are probably in need of replacement, and have nothing to do with the reverse lights.

Jan 17, 2010 | 1996 Jeep Grand Cherokee

1 Answer

Reverse lights do not work, and the licsence plate


Someone has fixed your wiring. Fix it back and the light work as they should.

Oct 03, 2009 | 1994 BMW 3 Series

1 Answer

How do I take the spare tire under the vehicle off


the factory jake handle should have a t on the end insert into the key way that should be just above the rear licsens plate and crank it down

Aug 03, 2009 | 1988 Plymouth Voyager

1 Answer

Reverse lights and license plate light dont work


Try link below, may point you in right direction, but you'll have to scroll down & find what you need. Otherwise I'd start from bumper with test light & work my way back toward front harness, after all fuses, plugs etc been checked.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800610de

Dec 06, 2008 | 1991 Toyota Pickup

Not finding what you are looking for?
2003 Mercury Grand Marquis Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...