Question about 1996 Chevrolet Blazer

1 Answer

I got four low and two hi istill cannot get four hi

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 95 Answers

I have seen the wires a the control moduel corrode

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Spare fuse number for headlights on 2007 g6


There are four 10A fuses: LH LOW (beam) FUSE 7; LH HI BEAM FUSE 11; RH LOW BEAM FUSE 9; and RH HI BEAM FUSE 12. The fuses are located in the underhood fuse block.

Sep 09, 2016 | 2007 Pontiac G6

1 Answer

Ineed to be able to get my 2002 toyota tacoma out of the heat mode. Even when I shut down the blower fan abd turn the heat to cold istill get heat coning into the cab.


Hi do check the heater control valve and blower control module possible malfunction or faulty, Valve normally situated in engine bay . module will be found on internal heater box .

May 01, 2015 | 2002 Toyota Tacoma

1 Answer

2005 jeep grand cherokee stuck in four wheel drive


are you in four wheel low or four wheel hi. if you are in four lo, put vehicle in neutral before trying to shift out and be at a complete stop. if you were in four hi, put vehicle in reverse and keep backing up, usually 4wd while come out and go back into 2wd

Mar 17, 2014 | 2005 Jeep Grand Cherokee

1 Answer

4x4 Will not engage


linkage may need adjusted, try adjusting, truck is 10 years old, if that doesn't work, might be an internal problem, don't think the worst, one step @ a time

Feb 23, 2013 | 2003 Chevrolet Silverado 1500

1 Answer

Put car in 4 wheel drive (pushed button) and now can't get in back into 2 wheel drive what am i doing wrong?


if you went to four low then you will need to be engine running with the transmission in neutral, to go back to 2 hi if it is in 4 hi then its not you it is something else because it is a shift on the fly system for two and four hi in any gearrange

Dec 18, 2010 | 2001 Chevrolet Blazer

1 Answer

Four wheel drive will not ingage in four low it only locks in hi


Vacumm leak in front axle preventing engagement.

Jan 23, 2010 | 1987 Jeep Wrangler

2 Answers

My 1999 chevy silverado 1500 four wheel drive won't engage. The truck is in 2wd now. When I push 4wd hi or low, I can hear the actuator try to engage the four wheel drive. The four hi or low button will...


You probably have a bad encoder motor.It is located on the side of the transfer case on the drivers side.It is black.The other problem they had with these was the switch but you have already replaced this so your next thing is the encoder motor.Hope this helps.Good luck.

Dec 28, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

2000 jeep grand cherokee four wheel hi not working but four low works fine


Does the rear axle still pull when in 4-hi? If so, then I'd say the shift fork on the transfer case is bent or worn.

Dec 08, 2009 | 2000 Jeep Grand Cherokee

2 Answers

1996 gmc 1500 four wheel drive


Have you checked the switch on the transfer case? Those switches tend to go bad and primarily operated the 4 wheel Hi.

Apr 13, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

1993 4X4 BLASER 4WHEEL DRIVE


Your blazer is equipped with a shift on the fly four wheel drive. That means that at speeds less than fifteen miles per hour you can shift into or out of four wheel drive by simply pushing the four wheel high button. If you wish to shift into four wheel low. Stop, put the transmission into park or neutral, and push the four wheel low button. Same procedure for shifting back out. Never shift into or out of four wheel low while moving. And be careful in four wheel low. At full throttle your still barely moving, you don't want to blow your engine up!

Dec 31, 2008 | 1994 Chevrolet S-10 Blazer

Not finding what you are looking for?
1996 Chevrolet Blazer Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...