Question about 1991 Chrysler LeBaron

5 Answers

1991 Le Baron Turn Signal Problem

Hello,

I recently picked up a 1991 Le Baron convertible. I have been having problems with the turn signals. The 4-way flashers work, but the turn signals do not work. I have replaced the yellow flasher unit along with the fuses and relays located along the inner wall underneath the driver's side dash. I replaced the diode package that the turn signal current runs through. The bulbs, sockets, and turn signal switch have been checked. I am still having problems. So, I went to a Chrysler dealer and asked for some input. He told me that the yellow flasher unit located to the right of the steering column ONLY controls the flashers and NOT the turn signals. I need to look for a separate disc-shaped unit that controls only the turn signals.
So, does anyone know anything about how these turn signals are wired? Where should I be looking for this separate turn signal unit?

Posted by on

  • 2 more comments 
  • dirtdoc13 Jul 11, 2008

    Thanks for the help. I have a Haynes Repair manual. This manual does contain VERY GENERAL wiring diagrams. It gives limited information about ALL midsize chrysler automobiles from '82 to '95. Therefore, it is not very detailed for the LeBaron. It is way too general. I have also checked at various libraries for books (like you say) that specifically pertain to the LeBaron. No luck so far. Any other help/suggestions anyone can throw my way would be greatly appreciated.

  • Anonymous Mar 14, 2014

    Where is the turn signal flasher control on a 1986 Nissan pick up

  • Anonymous Mar 20, 2014

    lites working no turn signal

  • Anonymous Mar 23, 2014

    Our daughters 2001 Concorde has no flashers or signals. My husband replaced the fuses & the relay flasher under the dash next to the brake pedal but they are still dead. Should we replace the signal switch or is there something else we can do first?

×

5 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Since all of the relays and fuses were good, I figured something wasn't working in the dash pod. So, in order to fix this problem, I had to replace the entire circuit board that the turn signal unit is plugged into. FYI. The 90 and 91 Le Barons (along with some later years) have what are called "combination flashers." This flasher unit controls BOTH the turn signals and the hazards. It is a yellow unit located under the dashboard to the right of the steering column. I was told to look for a disc-shaped flasher that controls only the turn signals. These disc-shaped flashers were used in earlier Le Barons and earlier Chrysler models, NOT the later ones.

Posted on Jul 15, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 3,422 Answers

Hi,
You'll find the problem to a failure of a connection in the switch itself. Fix that, and you will have no problem. The plug-in that may not be making contact which is under the cowl that goes over the instrument panel. 3 screws hold the underside of the cowl panel in place. Once that is removed you can see the switch connecter on the left hand side. Turn the key on to activate the turn signal switch in the left turn position and gently wiggle the connection till the left turn signal comes on.may even try spraying some electronic tuner cleaner but very sparingly. Button everything back up and you should be in fine shape. By the way, Chrysler no longer makes the remote turn signal/dimmer switch for these model Lebarons. That particular remote switch was used in the 1990 thru 1994 Lebaron coupes and convertibles. Should you ever have need of the switch itself about the only place you could find one would be in a salvage yard. The part number for the switch is 5269468.
hopes this helps.
Good luck

Posted on Jul 11, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,472 Answers
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 250 Answers

The first thing I would do is goto Autozone and have them pull the part. Take a look at it so you know what you're looking for. Also, many times autozone has diagrams in thier computer that shows how to connect the part. Have them look for that too and show it to you. This is where I always start when I'm not exactly sure what a part looks like or where it's located.

Posted on Jul 11, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 555 Answers

A Clymer Guide or similar manual will show you the wiring schematic. Should be available online, or in your library.

Posted on Jul 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Left turn signal works intermittently.


Hello. You may have a faulty turn signal switch or an expensive relay module. A turn signal switch is way cheaper than a relay module.

Apr 02, 2014 | 1991 Toyota Pickup

1 Answer

1991 honda civic turn signal problem


I can't recall as its been a while since I've worked on the older Civics, but there may be 2 bulbs in the cluster. They are not that hard to pop out and have a look.

Jun 17, 2013 | 1991 Honda Civic

2 Answers

2004 Chrys Concorde, new utility trailer, tail light converter. Problem: There is output from conv box in yellow wire, when turn signal is on, but when it is connected to the trailer harness, no output...


Your vehicle CANNOT be wired for a trailer without using the converter box. The only vehicles that do not require a converter box are the vehicles that use the stop lamp bulb as a turn signal. Your vehicle is equipped with SEPARATE stop lamp and turn signal bulbs.

To make the converter box work correctly, it must be wired according to the instructions to BOTH the stop lamps AND the turn lamps. The tail (or PARK) lamps DO NOT go through the converter box.
Your trailer uses the SAME bulb for stop and turn - THIS is the reason you need a converter.

The wire color for both your LEFT TURN and your RIGHT TURN are LIGHT GREEN/TAN. Although the wire colors are the same at the bulb sockets, these are SEPARATE circuits and must be wired to the correct wire at the converter box. (LEFT and RIGHT) The converter box will have an INPUT connection for EACH of these.

The wire color for your STOP lamps is WHITE/TAN. The converter box should only have one INPUT wire that connects to this. It doesn't matter which side of the vehicle you connect this wire to. All of the stop lamps are on the same circuit.

The converter will then have only one wire for LEFT turn and stop (usually YELLOW) this is the wire that needs to go to your trailer connector for left turn and stop.
The RIGHT turn and stop will most likely be GREEN coming out of the converter.

Sep 05, 2011 | Chrysler Concorde Cars & Trucks

1 Answer

There is no fuse box cover inside of 1991 galant to see where the turn signal relay is? Where can I find free diagram to locate what fuse is what?


hello, turn signal relay is round, it plugs into your fuse panel, it should be the size of a quarter round, you have relay for brakes and turn signals, both are round, and they are only about 1 inch to inc half long, eay to spot them, they are only two round plastic things that plugs into fuse box,

Feb 06, 2010 | 1991 Mitsubishi Galant

1 Answer

Right rear taillight keeps sending a brake light out on my cousins 1989 Chrysler Le Baron. Yet every time I remove/replace the same bulb it will work for a short period of time then send the signal again...


make sure you put in the right bulb. different bulbs have different resistance ratings. if this is not the problem yhen you may need to replace the receptical.

Dec 18, 2009 | 1989 Chrysler LeBaron

1 Answer

Signal light and Windshield-Washer Pump


The wipers & turn signals are all in one unit, called a combo switch. It sounds like there is a short in switch which means you will have to replace the whole thing.

May 15, 2009 | 1991 Honda Accord

1 Answer

Turn Signal Failure


TRUE DAVE FROM THE SOUNDS OF THIS IT'S PROBLY A BAD RELAY THATS STUCK OPEN OR CLOSED

Apr 12, 2009 | 1998 Chevrolet Blazer

1 Answer

The turn signals don't work in the rear of my 1991chevy s-10.


Hello, I see you are having problems with you turn signal and brake lights on a 91 s10. If you will try switching the hazzard flasher off and on several times and shaking the turn signal left turn to right turn several times that may get the signals and brake to working again. The are probably just not making good connections inside. Thank You.

Feb 23, 2009 | 1991 Chevrolet S-10

2 Answers

1991 buick regal brakelight and left signal


I would check the wire leads to the light inside the truck. The trunk seals are prone to leaking and cause the exposed wires and leads to rust out. If they are dirty or rusted up, pull out one wire connector at a time from the wire harness plug going into the light. Take a fine grit sandpaper and clean it up. If the break off or are brittle, go to your local Radio Shack and pick up some new ones for about a buck. Cut the old ones off the wire and crimp the new ones on with a pair of needle nose pliers... Easy cheap fix...

Jan 07, 2009 | 1991 Buick Regal

1 Answer

Turn signal will not ''flash'' on /off-cops pulled me over about it


The problem is most likely not a bulb and certainly not a fuse but the 'flasher'. The flasher is located under the driver's side A/C duct above the fuse box. It just plugs in so you shouldn't need any tools.

Dec 13, 2008 | 1991 Plymouth Acclaim

Not finding what you are looking for?
1991 Chrysler LeBaron Logo

2,155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...