Question about GMC Yukon

Open Question

POWER ADJUSTABLE PEDALS IS NOT WORKING,i JUST BOUGHT A USED CAR YUKON 2006,I TRIED TO PRESS THE BOTTON FOR THE ADJUSTABLE PEDAL BUT IT IS NOT WORKING.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: engine drops speed when I press gas pedal

Ignition distributor caused problem. Rotor element needs replacement.

Posted on Aug 04, 2008

Ad
  • 190 Answers

SOURCE: shakes looses power to the engine when i press gas pedal driving.

Sounds like you have a Bad ground to the Engine Block,
Add a second Ground to the Engine Block, Every time you hit the Gas the Engine lifts up and you lose ground..

Posted on Feb 04, 2009

RJones1125
  • 373 Answers

SOURCE: GAS PEDAL NOT WORKING/2001 LINCOLN LS

inspect throttle linkage, it may be disconnected or broken

Posted on Feb 28, 2009

jim9813
  • 124 Answers

SOURCE: 2004 Supercrew Lariat no driver power seat or pedal adjust

Maybe, you can diag yourself with a test light and an ohmmeter. These will cost less at sears than having a dealer diag it. Check fuse 109 in the cab, that's the fuse for the driver's seat module. If that fuse is ok, then check power at the module. It's a little black box under the driver's seat with i think 3 connectors. Back probe the dark green wire at the connector with a test light, you should have power, even with the key off. If not, repair the circuit. Clamp the test light to battery positive and back probe the black wire, if the light does not light, repair that ground circuit. Test the memory set switch by measuring with an ohmmeter points 7 and 2, 7 and 6, 7 and 5 resistance should be less than 5 ohms, if not replace it. If all these tests pass, disconnect the connectors from the module and give 12v to the red and white wire. If the seat moves, have the module replaced at the dealer, it will have to be programmed.

Posted on Aug 10, 2009

  • 131 Answers

SOURCE: I had the front disk brake pads and rotors

check you fluid brake fluid level, and rebleed the system. that should help it out, sounds like you may have air in the line.hope this helps

Posted on Aug 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Brakelights dont work car wont shift


THE SHIFTER INTERLOCK RECEIVES ITS SIGNAL FROM THE BRAKELITE SWITCH.. NO BRAKE LIGHTS NO SHIFTY. CHECK THE STOPLITE SWITCH ON THE BRAKE PEDAL ARM

Nov 08, 2013 | 2006 Cadillac CTS

1 Answer

My brake lights stay on until I begin to press the brakes my car. When I press the brakes on my car, the brake light won't turn on and won't turn back on. Does this mean I need to replace my brake...


on your brake pedal yuo have a switch to turn off the brake lights when not in use and when depressed turns on yuor brake lights. i would suggest either trying to adjust them on the pedal and if not replace the switch.

Sep 30, 2011 | 2006 Pontiac G6

2 Answers

1999 GMC Yukon, Do I need to replace the stop light switch if my brake lights only come on when I push the pedal real hard to the floor. I have already replaced the brakes and did a new brake booster. Is...


Sounds like you are on the right road with the switch. Before I bought a new switch I would locate the switch, it will come in direct contact with the brake pedal arm, and see if there is an adjustment or if it has moved for some odd reason. Sometimes things just happen.

Jan 28, 2011 | 1999 GMC Yukon

1 Answer

The brake lights on my 2000 yukon denali stopped working, The upper light works and I checked the fuses. I replaced the bulbs. The running lights work fine.


If the circuit has power and the fuse is good the problem is most likely the switch. Look under the dash above the brake pedal arm. There is a small plunger type switch which is activated when the brake pedal is depressed. Sometimes this switch gets loose and or out of adjustment. There are two nuts on the shaft (one on each side of the mount). They should be adjusted so the brake lights activate when the brake pedal is depressed about 1/2 inch. If adjustment does not activate the lights use a multimeter and see if the switch is good by touching each of the two wires and depressing and releasing the switch. If there is no difference replace the switch.

Jan 03, 2011 | 2000 GMC Denali

1 Answer

Code p2120 and P2125 on GMC Yukon 5.3 2006 with low engine power message. can you please tell me whats that .


OBD-II code P2120 What does it mean? Throttle/Pedal Position Sensor/Switch "D" Circuit

Poooooooooo2125
ThrottlP2125
ThrP2125
Throttle/Pedal Position Sensor/Switch "E"ottle/Pedal Position Sensor/Switch "E"e/Pedal Position Sensor/Switch "E"

May 27, 2010 | 2006 GMC Yukon

1 Answer

GMC Yukon - ABS light and parking brake light come on while driving but they will go out if the car is restarted. Could it be a sensor or ECBM?


try to pull up on your parking brake pedal with your hand when light comes on. if this makes it go out u will need to adjust the parking brake switch under the pedal. or replace pedal spring that holds it up.

Oct 02, 2009 | 2002 GMC Yukon XL

1 Answer

Just bought 99 Hombre. My clutch pedal dose not work right


yes you can adjust the clutch unless it is already adjusted as far as it can be then you may have to replace it

Aug 30, 2009 | 1999 Isuzu Hombre

1 Answer

I have a 2006 gmc yukon and just had it for 1 year and the engine came on yesterday and did oil change but still on i thought that since i have 22,inch rims that was the problem


check owners manual for reset procedure. or try the key in on position so dashlights are on & holds gas pedal to floor or key on & pump gas pedal 3xs. or call dealer

Jun 20, 2009 | 2005 GMC Yukon

2 Answers

Brake lights stay on till the pedal is pulled back not the switch I replaced it


Two things come to mind:

1) Pivot bushing on the pedal swing arm might be bad.

2) It could be the brake master cylinder is sticking/binding and not allowing it to return all the way. The MC connecting rod may need adjusting, too.

May 03, 2009 | 1992 GMC Yukon

1 Answer

EMERGENCY BRAKE PEDAL GOES DOWN TO THE FLOOR WHEN ENGAGED


sounds like you have a worn set of park break shoes. they are located inside /behind the read rotors. if you remove the rotor and the shoes look fine then you can adjust them with the little star gear located on the bottom of the brake shoes.

Apr 28, 2009 | 2001 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...