Question about 1987 Nissan Stanza
first of all you need to know what is the starter in order to remove it. if you can trace the big wire that comes from the positive wire of your battery to a big round thing at the bottom part of the engine. that round thing is the starter. before you start removing bolts, remove first that big wire from the positive terminal of the battery. it is normally bolted to the engine by three or two bolts. there are two wires that you need to remove first before removing the starter. a big wire from the battery and a small wire that controls the solenoid of the starter. after you remove the wire, remove the bolts that is holding the starter in place and the starter would drop down. the you can repalce it or repair it.
i hope i was able to solve your problem. please rate me.. tnx.
Posted on Jul 09, 2008
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Aug 31, 2012 | 1987 Nissan Stanza
Nov 15, 2010 | 1990 Nissan Stanza
NISSAN STANZA WAGON - Manual Transmission
Q. Where is the starter on a 1986 nissan stanza station wagon and how do you get to it ?
Due to limited access to the starter, it is recommended that the transaxle be removed when servicing the starter.
1. Cold vehicle.
Remove 2 mounting bracket bolts, 10 & 12 mm (Figure 1).
Remove top starter motor bolt 14 mm with universal & long extensions.
Raise vehicle on hoist.
Remove front splash pans 10 mm.
Automatic transmission: Drain 2 qts out.
Remove rt-ft wheel 21 mm., & tie rod (Figure 3), axle cap, cotter pin, adj-nut & rubber washer.
Remove ball joint nuts 17 mm., left lower control arm 19mm. & swaybar bracket 14 mm. (Fig 2).
Remove axle nut 36mm (Figure 4), the front tube, catalytic converter heat insulators 10mm, ctr ex-tube 17 mm., and front tube from exhaust system (Figure 5).
Remove long bolt from ft engine mount (next to radiator), 17mm socket (Figure 6, Item A).
Remove tension rod mount 14 mm. Has adj-bracket with rubber insulators (Fig 6, Items B, C).
Remove right side drive shaft bolts that hold shaft to bracket mounted on engine (Fig7) 12mm.
CAUTION: Transaxle side seals are cut by spline teeth.
Install hoist type transmission jack and wooden block under the transmission/engine. Be certain the transmission is safely balanced on the hoist.
Remove 5 engine crossmember mounts (3 bolts, 2 nuts) 14mm.
Remove nut that attaches crossmember to engine mount.
Loosen stabilizer bar mounts to allow adequate clearance for crossmember to be removed.
Remove following brackets to allow starter assembly to pass through bottom:
tubular support bracket - engine to transaxle
angled support bracket - driveshaft bracket to engine mount
manifold collector stay - (bottom bolts)
Loosen top bolts, remove bracket above driveshaft-holding bracket 14mm.
NOTE: This bracket is slotted to allow it to slide out without completely removing the bolts.
Remove bottom starter motor mounting bolt.
Separate starter assembly from bellhousing, DC all cables/connectors, remove starter motor.
When installing starter, connect cable, install/torque starter bolts.
Nov 03, 2010 | 1986 Nissan Stanza
Sep 18, 2010 | 1992 Nissan Stanza
May 20, 2010 | 1989 Nissan Stanza
Dec 15, 2008 | 1987 Nissan Stanza
Nov 17, 2008 | 1991 Nissan Sentra 2 Door
Nov 07, 2008 | 1987 Nissan Stanza
Jan 24, 2014 | 1987 Nissan Stanza
198 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: