2002 chevy 2.2 liter belt diagram - S 10 Chevrolet Cars & Trucks

T_330_81_1981_Chevrolet_Light_Duty_Truck_10_to_30_Service_Manual
http://www.73-87chevytrucks.com/techinfo/7387CKMans//Service/ST_330_81_1981_Chevrolet_Light_Duty_Truck_10_to_30_Service_Manual.pdf

GMC Workshop Manuals

Diagram courtesy of AutoZone.com

Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.

3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.

4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.

5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.

6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

Hi: Hope this Diagram Downloads Right. This diagram is for a 3.5 liter


Below is Diagram 3.0 liter Toyota Camry


Diagrams Courtesy of Autozone Please let me if these are what you needed?

Thank You From: d_hubbs

this should help you, please leave a good feedback thankyou and good luck.

Go to the web site below. (copy and paste the address into your browser).

http://www.daycoproducts.com/daycoweb.nsf/cf652a4feb630ad0862571a4005ae40c/a866a821123f887c862571a5006988df!OpenDocument

Above the photo are 2 PDF documents. The first - Routing Guide gives you the diagram code for the car and engine. See page 30 for the 89 CHEV Corsica 2 liter.
There are 2 belts - one for the air conditioned equipped engine (diagram 6-3) and one without the aircon (diagram 5.3).

Next go to the second document - Illustration guide PDF document - for those 2 belt diagrams.

Cheers
Sean
- Voluntary contributor.

here is an image of the engine in question (on the right) it is not a diagram but shows the track of the serpentine belt

http://static.howstuffworks.com/gif/1999-2000-2001-2002-2003-2004-ford-mustang-5.jpg

Below is the diagram you requested. Kindly return to rate this solution and thank you for using Fixya!
Greg

Copyright © 2002 Delmar, All Rights Reserved.

Ford explorer 4.0 liter motors have 2 timing chains. If they don't rattle, leave them alone.