Question about Chevrolet S 10

1 Answer

My 2002 s 10 will not go into 4 wheel high i have taken it to my local garage 3 times to fix it and they tell me they have cleaned the burs off the chain, and greased it, they have cleaned the corrosion off the transfer case module and lubed it and they have replaced the transfer case module. and each time they say it works fine for them. when i go to pick it up it will go in maybe one time then it stops working, it will not switch from 2wheel to 4high while in motion, but sometimes when i stop and put it in neutral and take my foot off the break it will go, then sometimes the lights on the 2wheel 4 high and 4 lo will all flash or all go out completely. any ideas. the shop has guarented there work so i am not paying for the last 3 visits but they arent fixing the problem.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 450 Answers

Get them to check the detent shift switches on transfer case for correct operation as well as the one on the front diff for the shift on the fly unit, these tell the module as to what state it is in.
2H,4L or 4H.

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1984 mazda rx7 fails emissions for not burning enough gas


What are the HC and CO readings? if it is not that far out, tell your tech to richen it up an 1/8 turn at a time. The factory starting point for the mixture screw should be 2 1/2 to 3 out from closed can go as much as 3 1/2. As long as the throttle plate setting has not been played with. If that is the case it will take a bit more to setup properly.

Mar 23, 2013 | 1984 Mazda RX-7

1 Answer

My Cousin has a 2003 Ford Ranger his ABS light stays on and the Garage wont pass the MOT till it is fixed. they sent the whole unit up to Glasgow to be looked at but there machine couldnt read it. he has...


ABS light,most of the time, indicates a bad wheel speed sensor.
If you don't have an American OBD2 connected code reader or scan tool.
unplug one wheel speed sensor at a time,put a volt meter on the two wires,
set meter to HZ, and see if you get a decent output ,when turning the wheel
Compare, to what most likely will be 1 or 3 other good ones.

Nov 26, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

Ford focus' wheel bearings (2000 lx)


is difficult you need a press and some special tools as torquemeter to set the nuts to avoid the worn out of the new bearings.try to a local garage.buy the parts by yourself and the cost isnt so high!

Apr 13, 2010 | 2000 Ford Focus

2 Answers

Abs light stays on my 99 subaru outback. what should i do to get it off


you have to go to your local garage and have the car computer scanned

this will tell you which wheel sensor is not working properly, or abs module

Feb 17, 2010 | 1999 Subaru Legacy

1 Answer

High pitched humming noise from rear near side


did they check the other wheel bearings? some time a wheel bearing noise will travel and sound some place different.

Jan 05, 2009 | 2000 Ford Focus

1 Answer

Can anyone helpme before i go to my local rip off garage. I have just bought a 1996 landrover discovery v8i es. the car is immaculate and has been well cared for. On my way home the tempreature gauge went...


go to a good garage and tell them to run a co2 test ,it is simple test where you take off the radiator cap start the engine , hold a vile over the cap opening if co2 is getting back to the radiator the solution in vile will change color and this is head gasket problem . if not could be thermostat or cap a good garage can test caps with pressure tester if good cange t-stat

Nov 06, 2008 | Land Rover Discovery Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...