Question about Jeep Cherokee

1 Answer

Cannot remove small bulb park light on jeep crd 2.8. The bulb is a BOSCH 233 12v 4w

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,400 Answers

Just push straight down and twist counter clockwise. If it's seized in socket you might have to break it and pull base out w/needle nose pliars.

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove parking light bulb on 2004 Porsche cayenne .I have removed the headlight unit but can't remove the bulb


You turn the bulbs socket

May even be an arrow on it

At the most you can see a release clip

Aug 12, 2014 | Cars & Trucks

1 Answer

How do i change the brake light on jeep liberty 2006?


1) You will need to open the rear swing door.

2) On the inside jam there are two torx headed screws (T-15's if I remember correctly).

3) Unscrew the two torx screws.

4) The light is now held by two mounting tabs (small spherical headed plastic sets that go through a rubber grommet).

5) You will need to pry the light casing off (easy pressure with a good size flat head screw driver will do the trick).

6) The light bulbs are twist mount settings inside the light casing.

7) Twist out the mount setting, change the bulbs, and reset the light mountings.

8) To put the light casing push the light casing back on and put in the screws. Everything else will work in reverse when it comes to assembling the whole unit.

2006 Jeep Liberty Replacement Light Bulb Sizes
Low Beam Headlamp Bulb Size: 9007
High Beam Headlamp Bulb Size: 9007
Parking Light Bulb Size: 2825 or 3157
Front Turn Signal Light Bulb Size: 3157
Rear Turn Signal Light Bulb Size: 3757ALL
Tail Light Bulb Size: 3157
Stop Light Bulb Size: 3157
High Mount Stop Light Bulb Size: 921
Fog/Driving Light Bulb Size: 9145 or H3-55W
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 3157
Front Side Marker Light Bulb Size: 168
Ash Tray Light Bulb Size: 161
Map Light Bulb Size: 578
Dome Light Bulb Size: 578
Step/Courtesy Light Bulb Size: 906
Trunk/Cargo Area Light Bulb Size: 578

Thank you for using fixya, and good luck

May 08, 2010 | 2006 Jeep Liberty

1 Answer

How do I replace the passenger side corner light and front side turn signal light?


Front Turn Signal & Parking Lights


7ccc73e.gif
Remove the 2 parking light housing retaining screws ...


9898a80.gif
... then pull the housing away from the vehicle far enough to remove the bulb socket from behind the housing. Turn the socket counterclockwise and pull


a323ae9.gif
Push the bulb in the socket gently and turn clockwise, then pull the bulb out of the socket. Note the offset retaining ears on each side of the bulb


  1. Remove the screws from the lens and separate the lens from the headlight bezel.
  2. Remove the headlight bezel.
  3. Remove the screws from the turn signal housing and pull it out.
  4. Turn the bulb socket counterclockwise 1/3 turn and remove it.
  5. Installation is the reverse of removal.


Side Marker Lights
  1. Remove the screws from the marker lens and separate the lens from the headlight bezel.
  2. Pull the bulb from its socket in the back of the lens.
  3. Installation is the reverse of removal.

Feb 14, 2010 | 1997 Jeep Grand Cherokee

1 Answer

How do i replace the fog lamp on a 2005 jeep liberty


is it the bulb or whole light assembly. Both are easy, the bulb has a slotted lock. turn the bulb to the left and it should come out. The assembly, under the front bumper, look at the light housing. There should be 2-4 small nuts mounting it to the surrounding body, once these are removed it will come out the backside.

Jan 01, 2010 | 2005 Jeep Liberty

2 Answers

How do I replace the turn signal bulb on my 1997 Jeep Grand Cherokee? It seems like I must remove alot of the front end to get at the bulb... is this true?


For the front turn signal:

There are two ways to get at the bulb.

Way 1) YOU NEED A SKINNY SHAFTED STAR SCREWDRIVER. This is how the manual describes it: Unscrew the 2 star screws holding the parking light housing on. One is on top, the other is between the parking light and the turn signal. This second screw can be very difficult to get to because the parking light and turn signal housing are very close. After the parking light housing is off, you can unscrew the turn signal housing. The screws should be located on top of the housing, underneath the parking light housing.

Way 2) This is the way I did mine: First, you have to take the headlight housing off. It should be pretty easy to pop off if you pry it the right way. It is held on by 1 square clip and 2 ball and socket clips. There is a small risk of breaking the ball and socket clips, as getting the headlamp housing off does require a little force, so be careful. You may want to take the headlight bulb out first, but isn't necessary. (Removing the right side bulb may require removing the battery) Once the headlamp housing is off, the turn signal bulbs should be very easy to get to.

To remove the bulb, simply turn the bulb socket and it will come out.


For the rear turn signal:


Open the lift gate.

There are 3 hex screws that hold each rear light assembly on. I'd recommend a hex screwdriver, as a socket wrench or box wrench would be very hard to use on the screws. Once the hex screws are off, just tug on the light assembly and it will come off. The bulbs are very easy to get to. The turn signal is the yellow one.

Nov 10, 2009 | 1997 Jeep Grand Cherokee

2 Answers

How do i get to the front turn signal bulb 1997 Jeep grand cherokee?


Front Turn Signal & Parking Lights

6bad7be.gif
Remove the 2 parking light housing retaining screws ...

36b7e3d.gif
... then pull the housing away from the vehicle far enough to remove the bulb socket from behind the housing. Turn the socket counterclockwise and pull

5206de4.gif
Push the bulb in the socket gently and turn clockwise, then pull the bulb out of the socket. Note the offset retaining ears on each side of the bulb

  1. Remove the screws from the lens and separate the lens from the headlight bezel.
  2. Remove the headlight bezel.
  3. Remove the screws from the turn signal housing and pull it out.
  4. Turn the bulb socket counterclockwise 1/3 turn and remove it.
  5. Installation is the reverse of removal.

Oct 12, 2009 | 2002 Jeep Grand Cherokee

1 Answer

2005 DIAGNOSTIC ERROR CODE P0069, CRD ENGINE WONT


Are you traveling high ground like Rocky Mountain?

I will remove the ground cable for 4 minutes to reset all data in ECU.///clock and radio stations too : (

Let the ECU to relearn the local environment parameter.



Here's so info on how to prevent vapor lock

Ride with full tank of gas but NO TOP OFF.

Crack open gas cap carefully during rest stops to release / equalize gas tank pressure'

http://www.estes-park-information.com/vapor-lock.html


Good Luck

Jul 15, 2009 | 2005 Jeep Liberty

1 Answer

How do I change the parking lightbulb?


In prying, I hope that you removed the screws first!!! Likely, there is one that you missed. Park light& turn signal light are connected to the housing around the headlight. When removing it, make sure you don't turn the adjusting screws for the headlight itself! The light socket turns 1/4 turn to left to disengage it. Be careful not to break bulb or you will cut yourself.. On some bulbs, match the small nubs in the sides of the brass part of the bulb to the slots in the socket. they are not the same (one high, one low) Use wd40 if socket is rusted to bulb.
That's about all I can tell you without going there & doing it for you!!!
Good luck!

Dec 26, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...