Question about Ford F-250

1 Answer

The light is broken and I need a new one - F-250 Ford Cars & Trucks

Posted by on

  • Mical Caterina
    Mical Caterina Jan 03, 2011

    need more info - year, model and what light???

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 17,129 Answers

You will need to source the part from Ford spares and replace after the mounting is removed .
you have not specified the details of the light- if headlight or other wise and if the damage is more than the assembly.
Please write in details for helping you .

Posted on Jan 03, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 Chevy Blazer 4.3 4WD 2DR brake lights on drivers side not functioning


Check to make sure you have a good ground. From there, you need a circuit tester light w/probe to trace back. Look for a broken wire.
Good Luck.

May 23, 2015 | 2000 Chevrolet Blazer

2 Answers

Interior door light stays on


Door switch stuck open or broken. Spray switch with wd40 to free it if it's stuck, replace if broken

Oct 23, 2014 | 2004 Volkswagen New Beetle Convertible

1 Answer

2006 jeep commander abs trac.control esp lights are on seems like abs is locking up 0ff and 0n


there is a small switch under brake bedal. when it is broken, you get a warning on your dash light and ABS and related equipment go into safe mode. you need a new one. other reason to this can be a broken sensor on one of brake calipers. those must be checked.

Jul 13, 2014 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Brake light switch wires broken


Here is a picture of the brake light switch. Also at this point just buy a new connector and splice it on, much easier.
1_15_2012_9_46_06_pm.jpg

Jan 15, 2012 | 2000 GMC Sierra 3500

1 Answer

Both bulbs on my 2002 S10 Blazer licence plate was burned out I replased them with new bulbs and they will not come on and I have checked the fuses what could be the problem?


you need to check for power and for ground at the lightbulb socket to determine which is not contributing to power the bulb(s). If the marker lights work at the rear then suspect a broken/melted light bulb socket, broken wire, or broken/rusted ground connection. Again, check at the light bulb socket for ground on one side (black wire) and 12V (brown wire) on the other. The light socket should have terminals that actually touch the light bulb; sometimes the sockets will melt not allowing a good connection. a cheap harbor freight multimeter (VOM) will help. Right and left side use separate fuses

Jan 13, 2012 | 2002 Chevrolet Blazer

2 Answers

2002 toyota 4runner


1.Crank position sensor or its circuitry is faulty.
replacement is reqired.
2.No fuel pump or fuse is out. New pump or new fuse required.
3.No spark. Coil(s) are out. New coil is required.
4.Distributor is broken or out of specs. New distributor cap and rotor needed.

any check engine lights? do you hear fuel pump?

Nov 25, 2011 | 2002 Toyota 4Runner

1 Answer

Brake pad warning light still on after fitting new pads


Hi
did you fit new pad warning wires. If there is a break in the wire the light will stay on. Even if you did fit new wires, the wire could be broken you can check this with a multimeter or battery and bulb. Don't for get any one of them could be broken or damaged and this will put you light on. Could even be a bad connection where your plug-in.

Jan 29, 2011 | 2010 Mercedes-Benz Sprinter

1 Answer

Replace broken turn signal


everything you will need you can find here:

http://www.ehow.com/videos-on_453_replace-turn-signal-switch.html

copy and paste in your address bar under new tab

Oct 06, 2009 | 1997 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...