Question about 1999 Dodge Durango

1 Answer

I have a new world dishwaser flashing e4 what is the problem

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Expert
  • 92 Answers

You can troubleshoot your dishwasher by

  • First check the manual to see if the machine has a specific troubleshooting guide.
  • Note all sounds or other symptoms the dishwasher shows.
  • Look for some of the more common problems. This includes water temperature deviations, poor washing, failed motor, overflows or leaks or door-latch problems, among others. Anything that can't be dealt with through your troubleshooting guide needs the use of a professional. Check for obvious causes, like blockage in any area or extremely dirty situations affecting water flow

  • you can also always troubleshoot your dishwasher by :

    Instructions Things You'll Need:
    • Dishwashing Detergent
    • Scrub Brushes
    • Steel Wool
    • Steel Wool
    • Screwdriver Sets
    1. Make sure the cord is plugged in and that the breaker hasn't tripped.
    2. Be certain that the door is completely closed and latched.
    3. Check that the cycle button is pushed in all the way.
    4. Check the sprayer arm and filter screen at the bottom. Are they obstructed by a loose piece of silverware or a plastic lid?
    5. Unscrew the cap holding the sprayer arm on; pull it and the screen beneath it out. Use a wire to poke obstructions out of the sprayer arm holes. (Don't use a toothpick because it could break off in the hole.) Scrub the screen with a scrub brush and a little bit of dishwasher detergent.
    6. Eliminate the following as sources of noise: low water pressure keeping the dishwasher from filling, dishes rattling against the sprayer arm or other dishes, loose items tumbling around or trapped in the bottom of the unit.
    7. Take apart the front door panel according to the manufacturer's instructions if the detergent dispenser isn't opening. It may be corroded or have a broken timer lever. If this is the case, rub the corrosion off with steel wool or replace the lever according to the owner's manual

    Posted on Jan 03, 2011

    Ad

    1 Suggested Answer

    6ya6ya
    • 2 Answers

    SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

    Hi,
    a 6ya expert can help you resolve that issue over the phone in a minute or two.
    best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
    the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
    click here to download the app (for users in the US for now) and get all the help you need.
    goodluck!

    Posted on Jan 02, 2017

    Ad

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Is this a hoax: australian pm adviser says climate change is 'un-led ruse to establish new world order'


    probably not
    the Australian PM is being led by the nose by the fossil fuel giants and refuses to acknowledge that there is a climate change problem
    His government has in fact reduced funding and crippled the climate change council so that they cannot report to the people
    the so called "new world order " is already starting around the world by every day people who are sick and tired of the wealthy destroying the planet in the name of profit

    Dec 04, 2016 | Cars & Trucks

    1 Answer

    Diognosis light pattern 316 keeps putting my 2004 fvz1400 isuzu into limp mode. i can not find a reference for this code


    light pattern, is that a light bulb? or means weak engine power
    or harsh misfiring?
    it has misfire, 2004
    7.8L diesel.? the 9L
    or TDI , ?\
    what code? ahhh , i get it light pattern is the engine ECU flash codes. yes, and is only in a ISUZU book , in your country
    no country stated so really nobody can look for you.
    worlds is huge, and these trucks are not same world wide.
    "smog laws' big time ....
    6HK1 (engine"?)

    go to isuzu dealer get book on this EFI diesel system
    and its all there, codes and all. (reasons for them all)\



    26334739-lfvi2b44iwkqit5d2rqve4gf-5-0.jpg

    Oct 31, 2016 | Isuzu Cars & Trucks

    1 Answer

    Need a wiring diagram for Delphi delco am FM CD player from a 2004 Chevy malibu


    According to http://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=2&ved=0CDMQFjAB&url=http%3A%2F%2Fwww.aircommand.com.au%2Fdocs%2FIbisTechManual.pdf&ei=29JPVfO8NYu9sAWE_YGQAg&usg=AFQjCNEPb_nNaXQsRrD2ZphXVLpRYwECGQ&sig2=cHErjmhdOfyCsep25gpmfw

    E4: Indicates lack of refrigerant, or the compressor is not running, or the thermistor is out of calibration. Action: Check that the compressor is running by listening. If it is apparent that the compressor is running, then check the temperature difference across the evaporator. i.e. Measure temperature of return air at inlet filters and measure temp. of discharge air at grilles. This temp diff. should be 14 to 18 C. with fan on hi speed. If temp diff. is less than this, suspect lack of refrigerant. Fit a suction gauge to access valve at rear of unit. See fig 12. On a 35C outside temp. then suction should be 380 to 450Kpa.
    Page 2
    Action (continued) If the temp. differential is 14C or more but unit goes out on E4 after approx. 30 minutes, please check the actual thermistor temperature by the following procedure. With the inside fan running on Hi. Press Temp down button followed by the mode button. Hold them both in for approx 5 seconds. The amber Lock LED illuminates. Now press the Temp down button and the Sleep button Together for about 1 second. The green Med speed will be Flashing. The display is now reading the temp of the outside coil. Now press the Temp up button once. The Green Hi speed will be flashing. The display is now reading the temp. of the inside coil. This temp will usually be from 5 to 12 C. If it is above 24C. It is another indication of lack of refigerant. If on the other hand the air on /air off differential is 14C or greater then suspect the thermistor itself to be out of calibration. Check the thermistor as per an E1,E2 or E3 failure by measuring its resistance. See fig 19 and referring to table 1.

    May 10, 2015 | 2004 Chevrolet Malibu

    1 Answer

    Where can I get a radio for my Suzuki grand vitara? The gear in my cd changer is damaged


    where to get ,
    what? a new radio, a used radio. or upgraded radio.
    a Suzuki radio or after market
    why not upgrade, its cheaper a $100 media center radio
    with USB memory stick with 1000s of songs MP3 on it>
    CDs and DVD are dead technology, see netflix drop DVD's
    everyone uses flash memory sticks, mines 1/2"/1/2" near invisible on dash.
    time to upgrade , the software to rip your CDs to Mp3 or wave is free.
    IMO,,, join the rest of the world. and dump spinning disks.
    that love to fail ,jam, scratch or break. easy

    Jan 30, 2015 | Suzuki Cars & Trucks

    1 Answer

    What wire is the live for the radio on a 54 plate mondeo


    2005 Pontiac Azteck Mondeo? ???????????
    what in the world is 54 plate.? (is this UK, jargon?)
    my guess is you need the schematic for the radio?
    and dont have the FSM,
    cars come new with 3 to 4 new radio systems. (options)
    my car had 5, (even sat radio and amps, and tons of other junk)
    only knowing that matters.
    to above all that open the FSM book, turn audio and see those.
    in the USA we have 3 top online sources to this too.
    the best is alldata.com but dont cover UK, cars, nor options.

    the RADios, have 3 hot wires, (inputs) and 1 output.
    1: power.
    2: dial lamp, (parking lights)
    3: memory. (newer cars are devoid of this with flash memory)
    4: power out to electric antenna.

    some with external AMPS, more.

    Jul 03, 2014 | 2005 Pontiac Aztek

    1 Answer

    What to do to read codes from check engine light


    short answer, bad question! GEN 5 , trecel,
    long:
    is this a USA,
    car,?? gee, why not say that. ????
    as each car in each country has different systems. OBD1, OBD1.5 , OBD2, JOBD, EOBD. etc. or worse.....
    did you look for the 16pin D-shell shaped DLC connector ? at drivers
    knee?


    so im blocked from being accurate, just that.... alone..
    and what engine? 5 engines world wide.... a fact.
    2E,3E,4E,5E (new twin cam in 95) or the 1N

    in 1995 some engines on some cars were full or 1/2 OBD2 compliant.
    that RIGHT, some with 4cyl are OBD1, and V6 OBD2, can prove it.

    some cars in 1995, are OBD2 and have no flash codes,
    some are compliant to OBD2 with a cable adaptor. 1.5 compliance
    the EPA will list this car and non compliant ever if 100% good,
    but connector is wrong, or get this, more than 1 meter for steering
    so, RTM. the manual never lies, and that manual is , THE FSM.
    http://actron.com/faq_detail.php?pid=16298&id=7
    fact2 the earliest OBD2 is 1994 car. 1996 is mandate.
    1995 cars are on LIMBO do your home work. ! or ask ?
    to ask answer all questions above, country and ENGINE

    Lots of disinformation on the web, i track this and know it.
    OMG , 1995.5 year cars, ouch.

    ok 1 step at a time.
    the light must glow key on, does, ,if not its burned out or stolen
    many cars, (vast) the nasty PO stole it so new owners can see truth.
    very common. in real world.

    short answer 2: can work (USA ONLY)!!!
    i found the OBD2 standard, OBD2 connector by right knee.
    i jacked in new scan took key on and its dead.
    i open hood, look up and see , EPA sticker and no OBD2 compliant word, bingo a OBD1.5 car, ask for help. (custom cable)

    tricky huh, i dont design them i only fix them i fix ECU/s

    Jan 11, 2014 | 1995 Toyota Tercel

    1 Answer

    2000 deville ses flashing


    Hmm a phantom flasher ? the world is agast in awe -so please explain whats flashing the car or the driver??

    Sep 08, 2013 | Cadillac DeVille Cars & Trucks

    1 Answer

    HELP, BMW 2001 325i engine code 8F, A8, E4, E3, F2, EF


    A8 is thermostat needs replacement, i just had mine done at Peter pan dealership

    Oct 04, 2012 | 2002 BMW 3 Series

    1 Answer

    It wont start at any level


    E4 indication? Like a error message? About what are talking here? Send us details

    Aug 09, 2012 | Cars & Trucks

    1 Answer

    Car stalls when cold, only generally first start of each day.


    My 2007 Sebring with the 2.4L World Engine had a similar problem when shifted from reverse to drive when engine was stone cold. The engine either hesitated significantly or stalled. Brought it back to the dealer and they found a TSB and installed new flash in the Powertrain Module. Never hesitated or stalled after they installed the new software.

    Mar 07, 2010 | 2007 Chrysler Sebring Sedan

    Not finding what you are looking for?
    1999 Dodge Durango Logo

    118 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...