Question about 1996 Toyota Tercel

1 Answer

Radiator hoses I just recently change my radiator. After installing it, I noticed that the water just empty out after driving it or the next day. There is no leak from the radiator or hoses, is there a possibility that it is going straight to the engine? I check my oil which I also change it recently and I only put like 3 1/2 quarts, but now it is more than what it was before.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

If the coolant is going into the engine the oil should look milky.
You might want to check your water pump to make sure has not worn out and is leaking from there.

Posted on Aug 24, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

01 dodge ram 1500 5.2L. Radiator was empty, filled it up and next day was empty too. No noticeable leak coming from under the truck (no puddles). I used anti-freeze and water from hose (well water) front...


it may only leak when driving..when the pressure increases. this leak could be internal as well as in a head gasket. fill it up and let it idle and get up to temp and check for leaks then.(never remove the rad cap from a hot engine)

Aug 05, 2013 | 2005 Dodge Ram 1500

1 Answer

1997 Chevy C1500 Coolant Leak


start engine until get hot enough for coolant get hot pressurize then turn off engine check for leaking coolant hose.

May 03, 2013 | Cars & Trucks

1 Answer

I want to change a water pump how do i start


drain coolant from radiator, there is a plug at the bottom of it, turn it counter-clockwise. take off the radiator cap to get the anti-freeze out faster.next, remove air breather components. don't forget to disconnect all rubber hoses attached. next, the shroud has to come off. now on too the radiator hoses, they have to be disconnected in order to be able to remove the now empty radiator. Still with me ? remember to use tape to identify where the hoses go if you never done this before. use numbers for the order if that can help. example : put number on each side of where the hose seperates from where it's attached like the thermostat housing to the top radiator hose. it may sound childish but if you do it that way, the last number you put on is gonna be the first place to start and you won't forget a step. next, remove drive belt, that's the rubber belt around every accessory like alternator, power-steering pump, crankshft and, of course, your water pump. how are we doing so far ?

Jul 05, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Honda Odyssey Coolant System Prob.


You may have air in the system. Run the car with the cap removed and the defrosters on allowing air to escape. Add antifreeze as needed to keep full while running. Fluid level will drop as thermostat opens.

Dec 14, 2009 | 1997 Honda Odyssey

1 Answer

How to replace a water pump on a 2003 yukon


Water Pump Replacement (4.8L, 5.3L and 6.0L Engines)
Removal Procedure
1. Drain the cooling system.
2. Loosen the air cleaner outlet duct clamps at these locations:
 Throttle body
 Mass Airflow/Intake Air Temperature (MAF/IAT) sensor
3. Remove the radiator inlet hose clip from the outlet duct.
4. Remove the air cleaner outlet duct.
5. If necessary, remove the engine sight shield.
6. Remove the radiator vent inlet hose from the radiator hose clips.
7. Reposition the inlet hose clamp at the water pump.
8. Remove the inlet hose from the water pump.
9. Remove the fan blade.
11. Reposition the outlet hose clamp at the water pump.
12. Remove the outlet hose from the water pump.
13. Reposition the surge tank outlet hose clamp at the water pump.
14. Remove the surge tank outlet hose from the water pump.
15. Reposition the heater inlet hose clamp at the water pump.
16. Remove the heater inlet hose from the water pump.
17. Remove the water pump bolts.
18. Remove the water pump and gaskets.
19. Discard the water pump gaskets
Installation Procedure Important: All gaskets surfaces are to be free of oil or other foreign material
during assembly.
1. Install the water pump and NEW gaskets
2. Install the water pump bolts.
3. Install the heater inlet hose to the water pump.
Zoom Sized for Print
Notice: Refer to Fastener Notice in Service and Precautions.
2.1. Tighten the bolts a first pass to 15 Nm (11 ft. lbs.).
2.2. Tighten the bolts a final pass to 30 Nm (22 ft. lbs.).
4. Position the heater inlet hose clamp at the water pump.
5. Install the surge tank outlet hose to the water pump.
6. Position the surge tank outlet hose clamp at the water pump.
7. Install the outlet hose to the water pump.
8. Position the outlet hose clamp at the water pump.
9. Install the accessory drive belt.
10. Install the fan blade.
11. Install the inlet hose to the water pump.
12. Position the inlet hose clamp at the water pump.
13. Install the engine vent inlet hose to the radiator hose clips.
14. If necessary, install the engine sight shield.
Important: Align the arrow at the throttle body end of the duct with the throttle
body attaching stud.
15. Install the air cleaner outlet duct
16. Install the radiator inlet hose clip to the outlet duct.
17. Tighten the air cleaner outlet duct clamps at these locations:
 Throttle body
 MAF/IAT sensor Tighten the clamps to 7 Nm (62 inch lbs.).
18. Fill the cooling system.

I hope this helps. The numbering is incorrect in the sequence but the instructions are correct.

Roy

Nov 06, 2009 | 2003 GMC Yukon

1 Answer

I have the same exact problem and 2003 4cyl.and same year car....


You may have had an air pocket in the system. What I would when you get part,is to run at idle with radiator cap off and let warm up from cold start. With heater setting on so as coolant can flow through that part of system. Of course keep eye on temp as it warms up. This can take a while as fans won't come on till thermostat is opening. check hoses as it warms. when hoses get "hot to touch" both upper and lower , put cap on and make sure overflow bottle is filled to its level.If it all seems to be going well then i would let fans cycle for 2 may be 3 time before test drive.

Jul 22, 2009 | 2003 Toyota Camry

2 Answers

My 1994 jeep grand cherokee laredo is running hot


could be a lot of different things. bad heater core, cracked, ripped, or soft hoses, crack in the radiator, bad thermostat, clogged lines. next time you run the vehicle, try to see if you can see under the hood to see where the steam is coming from. that will help you to see if there is a bad line or hose. then try to flush the radiator to see if there is a clog in the lines. then go to get a new thermostat if none of those. then you get into the more expensive items the heater core and the radiator.

Jun 24, 2009 | 1994 Jeep Grand Cherokee

1 Answer

Overheating 2001 pontiac aztek


remove coolant.remove thermostat remove bottom radiator hose to water pump.put a empty container under the radiator.take a water hose put it where thermostat goes flush out the rust in block.watch the water as it come out the water pump .if stream water is small keep flushing until you get a study sream of clear water. also flush out radiator. lower water pressure dont flush radiator it with high water pressure you could burst it. make clean the over flow jug .make sure it not stopped up.put in a new thermostat and radiator pressure cap. fill radiator with half antifreeze and half water.bleed the coolant system.

Apr 05, 2009 | 2001 Pontiac Aztek

1 Answer

Top radiator hose


you may have a bad thermostat . i would start there .try flashing the motor with a garden hose ok have a nice day

Mar 29, 2009 | 2001 Chevrolet Venture

2 Answers

'97 subaru overheating


head gasket most likely.

Aug 21, 2008 | 1997 Subaru Outback

Not finding what you are looking for?
1996 Toyota Tercel Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...