Question about 1998 Toyota Corolla

1 Answer

Cant remove dash to change globe near fuel gauge

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Toyota Master
  • 1,348 Answers

You need to disconnect the speedometer cable at the transmission.otherwise the cluster will not pull out far enough to undo the plugs on the back.

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does the fuel gauge works with a separate fuse


most fuel gauges draw power from the dash gauge or panel accessory's fuse ,if only that one gauge is bad , most likely the sender in the fuel tank has let out and died on you , tank will need drained and removed to change this sensor , also I did have the little plug on sensor on tank pop off one time on me that kept the gauge from working too

Nov 22, 2016 | Cars & Trucks

1 Answer

Where do I find the ground unit for the gas gauge on a 95 Honda passport. I went and changed the dash board lights and the gas gauge started tripping and stopped working need help


If the fuel guage worked prior to changing the bulbs the ground should be ok. The only thing disturbed was the cluster assembly when you removed it. Recheck the connections at the back of the cluster again for tight connections and making sure there are no bent pins. You can also try tapping on the cluster near the fuel guage area to see if that helps

Jul 12, 2015 | Honda Cars & Trucks

1 Answer

MY HONDA STREAM FUEL GAUGE IS NOT WORKING,WHAT COULD BE THE PROBLEM


Could be fuse, faulty sender in the tank, broken wire (usually at tank or in dash near gauge) or bad gauge. To test, remove wire going to sender at the tank and briefly ground it while someone looks at gauge (key on, obviously). If gauge goes to max, problem is either ground wire outside of tank, or sender inside. If no effect, likely bad dash gauge.

Jan 22, 2015 | Honda Stream Cars & Trucks

2 Answers

Why does Temperature gauge reads hotter then normal but engine temp. is ok


some times after market senders read hotter if there not quiet the same value

Aug 15, 2014 | 2002 Audi TT

1 Answer

Fuel gauge lights up when empty but cant read fuel level how do i fix it


You need to decide if the tank sending unit or dash gauge is at fault.
The way to do that is remove the wire to the tank sending unit, and ground it out.
The gauge should rise to full.
If not, the gauge is bad.
If it does, then the sending using needs replacement.

Jan 21, 2011 | Toyota Corolla Cars & Trucks

1 Answer

2001 Nissan Micra replace fuel gauge bulb


need to remove instrument cluster to get to globe from the back,should be mounting screws in front to remove around instruments

Oct 21, 2009 | Nissan Se R Cars & Trucks

1 Answer

Cant get front dash speakers out of 87 deville


Top of dash must be removed. 2 bolts vertical in glove box 4 screws in defroster ducts, Remove 2 outer A/C air deflectors and 2 center deflectors. Be careful. Remove screws BEHIND A/C deflectors. Remove vertical screws along width of dash near speedo etc. Remove dash top and disconnect wires. Hope this helps

Jun 16, 2009 | 1987 Cadillac DeVille

1 Answer

High-beam indicator does not work


Sorry but the gauges have to be removed to replace the globe.Not the whole dash though,just the gauge surround and gauges only have to be pulled out far enough to get your hand in to change the globe.Good luck

Nov 11, 2008 | 2003 Toyota Camry

1 Answer

The gauges have stopped working ? Fuse under dash seems to be OK ?


Behind the dash is what they call a constant voltage regulator. It controls the guages. It's small and located behind the dash near speedo.

May 24, 2008 | 1966 Ford Mustang

Not finding what you are looking for?
1998 Toyota Corolla Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...