Question about 2000 Chrysler Concorde

Open Question

How do I remove the instrument cluster to replace the dash light for the speedometer and all that (also need to replace the flasher too)?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

shaggyrat
  • 1224 Answers

SOURCE: Instrument cluster failure causes fuse #29 to blow.

ok it could be quite simple
lets look at wrong size fuse
example 15 and you need a 25 fuse
also if you did any work on vehicle its quite possible that you grounded something out wrong retrace your work and fix accordingly
bad cluster relay is another problem that would cause these problems

Posted on Jun 10, 2008

  • 18 Answers

SOURCE: 1991 Volvo 740GL Speedometer

I remove two panel underneath the steering column. The first panel is removed using a 10 mm socket. The second panel is removed using a torx socket (can't remember the size). Removing these two panels gives you room to get to the clip on speedomter. Looking at the speedometer, you should see two rectangular holes on each side of the speedometer cover. I use a awl to push in the clip (you could use a screwdriver). Looking underneath the dash, you should be able to see the clip you are pushing on with the awl. I take my 2nd awl and put it behind the clip. I get the left side to release. One the speedometer cover releases, you can see the speedometer. You will see the 4 torx screws (t20) and two smaller clips holding the speedometer. All that is left is the wiring. (I take a sharpie pen and mark one of my wire locations on the speedometer. I am not sure what it does. It is a single wire.)

Posted on Aug 20, 2008

  • 341 Answers

SOURCE: instrument cluster removal 2001 buick century

no you have to remove trim most gm you just pull on trim & pops off then remove 4 screws lift out cluster

Posted on Oct 20, 2008

  • 1170 Answers

SOURCE: My bmw 318is instrument cluster doesnt work

The fuse must have blown off. Replace the fuse.

Posted on Mar 24, 2009

  • 73 Answers

SOURCE: Need to replace burnt out dash board lights 2001 Toyota Corolla

Just remove the 4 screws and then slowly pull the cluster out and reach behind and disconnect the plugs on the back of the unit and then remove the cluster. The bulbs can be removed by turning them and pulling out.

Posted on Sep 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the speedometer cable in a 1998 chevy tracker


Removal Procedure
  1. Remove the instrument cluster assembly. Refer to Instrument Cluster Replacement .
  2. Unhook the speedometer cable from the heater case.
  3. Remove the grommet from the bulkhead.
  4. Feed the speedometer cable through the bulkhead.
  5. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
Unscrew the speedometer cable (1) from either the transfer case or the transmission. Remove the speedometer cable (1) from either the transfer case or the transmission. Remove the speedometer cable (1) from the clamp. Remove the speedometer cable (1) from the vehicle.
Instrument Cluster Replacement
Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.
Disconnect the negative battery cable. Remove the hazard lamps switch by gently pulling the knob straight up. Remove the instrument cluster bezel from the instrument panel. Refer to Instrument Panel Cluster Trim Plate Bezel Replacement . Remove the 4 screws and pull the instrument cluster assembly forward from the instrument panel. Disconnect the 3 electrical connectors. Remove the speedometer cable at the speedometer head. Remove the instrument cluster assembly from the vehicle.
Remove the 5 screws (2) and the steering column upper and lower covers (1, 3).
Remove the 4 screws and the instrument cluster bezel from the vehicle.

Jun 17, 2015 | 1998 Chevrolet Tracker

1 Answer

How do I REPLACE light to speedometer honda odyssey 2006


You will first have to remove the screws that hold the dash surrounding the instrument cluster then use molding tools to help pop the panels off to access the instrument panel/ Once you get to the panel and remove it here is a good video that will help with the rest.

Dec 29, 2014 | 2004 Honda Odyssey

1 Answer

Replacing speedometer light on 95 jeep wrangler


the instrument cluster should not be a problem. there should be bolts holding the front dashplate in, just look in odd places on the front, sides, and bottom of the dash to remove it. after removing the plate, your instrument cluster should be easy to remove.

Apr 07, 2013 | 1995 Jeep Wrangler

1 Answer

My 89' ford ranger will not pass smog here in socialist california. it has passed for 15 years since i've had it. the new machines indicate that the check engine light is'nt operating. i...


Hi, it's possible the bulb is burned out or not making good contact with the circuit board. It should come on during the bulb check when you first turn the key on. Pull out the cluster and check the bulb. If it's good, see if you can clean the contact surfaces to get it working again. Or, move to another state where they don't worry about stupid things like a light bulb.

REMOVAL & INSTALLATION

See Figures 1, 2, 3, 4, 5 and 6


jturcotte_2200.gif

Fig. Fig. 1: To remove the instrument cluster, first remove the trim panel by removing the lower fascia panel


jturcotte_2201.gif

Fig. Fig. 2: With the lower fascia moved aside, remove the lower trim panel attaching screws ...


jturcotte_2202.gif

Fig. Fig. 3: ... as well as the upper attaching screws


jturcotte_2203.gif

Fig. Fig. 4: Then pull the entire instrument trim panel from the dash board


jturcotte_2204.gif

Fig. Fig. 5: Exploded view of the instrument cluster


jturcotte_2205.gif

Fig. Fig. 6: Rear view of the instrument cluster wire routing and connections

  1. Disconnect the battery ground cable.
  2. Remove the two steering column shroud-to-panel retaining screws and remove the shroud.
  3. Remove the lower instrument panel trim.
  4. Remove the cluster trim cover from the instrument panel by removing the eight screws.
  5. Remove the four instrument cluster to panel retaining screws.
  6. Position the cluster slightly away from the panel for access to the back of the cluster to disconnect the speedometer.

If there is not sufficient access to disengage the speedometer cable from the speedometer, it may be necessary to remove the speedometer cable at the transmission and pull cable through cowl, to allow room to reach the speedometer quick disconnect.
  1. Disconnect the wiring harness connector from the printed circuit, and any bulb-and-socket assemblies from the wiring harness to the cluster assembly and remove the cluster assembly from the instrument panel.

To install:
  1. Apply approximately 1 / 8 in. diameter ball of D7AZ-19A331-A Silicone Dielectric compound or equivalent in the drive hole of the speedometer head.
  2. Position the cluster near its opening in the instrument panel.
  3. Connect the wiring harness connector to the printed circuit, and any bulb-and-socket assemblies from the wiring harness to the cluster assembly.
  4. Position the cluster to the instrument panel and install the four cluster to panel retaining screws.
  5. Install the panel trim covers and the steering column shroud.
  6. Connect the battery ground cable.
  7. Check operation of all gauges, lamps and signals.

Sep 07, 2011 | 1989 Ford Ranger

1 Answer

All my gauges work except my speedometer. What is going on?


Check your speedometer cable at both ends and make sure it is on tight. If the speeometer cable is the original cable it might be time to replace it with a new one. The cable will wear out over time and cause your speedometer to stop working when you drive your car. A replacement cable will cost around $15. If your speedometer cable is good and in working order then you will have to have your instrument cluster repaired. Take a trip to your local junk yard and find your vehicle and then remove that instrument cluster and replace your broken unit. This is cheaper then having your original instrument cluster rebuilt at a shop. If your instrument cluster is digital, check the fuse box located underneath the drivers side steering wheel and locate the "instrument cluster" or "speedometer" fuse. Pull it out and replace it with the same number fuse. To remove your instrument cluster, remove the four phillips screws holding your plastic bezel that surrounds the cluster and then remove the four phillips screws that hold the instrument cluster in place. Now pull it away from the dash and disconnect the electrical plugs. This is very easy to do at home using a phillips screwdriver. If you have any more question, feel free to contact me.

michael34

Mar 09, 2011 | 1987 Nissan 200SX

2 Answers

Where is the flasher located for signal lights,all lamps are ok. can manually flash on/off,but don't flash automatically.


Hazzard/Turn Signal Flasher (With Analog Instrument Cluster) On Convinience Center
Hazzard/Turn Signal Flasher (With Digital Instrument Cluster) On Instrument Panel Fuse Block
I personally call the "Convinience Center" the INCONVINIENT CENTER. You have to remove the entire lower end of the dash to get to it. (about 10 screws, 4or 5 push clips, and a bunch of wrestling) Then you will find it at the lower center of the dash.

Jan 05, 2011 | 1995 GMC Sonoma

1 Answer

How do I access the dash lights for the speedometer and the tachometere? You cannot easily remove the dash. Are they accessible through an air vent?


you can do it like this. Let me know if you have questions.

  1. Disconnect the negative battery cable. Wait at least 90 seconds for models equipped with an air bag.
CAUTION Some models covered by this guide may be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS.
  1. Remove the fuse box cover from under the left side of the instrument panel.
  2. Remove the heater control knobs.
  3. Using a screwdriver, carefully pry off the heater control panel.

adbb67a.gif
Fig. Pull the finish panel and disconnect the wiring harness from the back

eb8d7ea.gif
Fig. Unscrew the instrument cluster from the dash . . .


ef30da2.gif


Fig. . . . then extract the assembly

  1. Unscrew the cluster finish panel retaining screws and pull out the bottom of the panel.
2aff1a4.gif

Fig. Detach the cluster wiring, you may want to label them prior



1c45d87.gif

Fig. Remove each bulb individually and inspect for replacement

  1. Remove the combination meter.
  2. Unplug all electrical harnesses and unhook the speedometer cable.

To install:
  1. Connect the speedometer cable and harnesses.
  2. Position the combination meter and secure into the dash.
  3. Install the cluster finish panel.
  4. Install the heater control panel with the control knobs.
  5. Install the fuse box cover if removed.
  6. Connect the negative battery cable.

Oct 31, 2010 | 1998 Toyota Avalon

1 Answer

Dash board is digital and the dash lights went out seeking information on how to remove the dash board console 1993 chevy blazer tahoe LT


Remove the 5 mounting screws from the instrument cluster trim plate and remove the trim plate. Remove the 4 mounting screws from the instrument panel face plate and remove the face plate.Remove the instrument light grid from the center of the cluster. From behind the instrument cluster reach behind the speedometer and disconnect the speedometer cable by releasing the tab. Pull the cluster forward just enough to detach the "check engine" light bulb from the center of the cluster. Remove the instrument cluster from the dashboard.

Jan 13, 2010 | 1993 Chevrolet S-10 Blazer

1 Answer

Looking to replace flasher switch looking for location


Left hand side of dash behind instrument cluster with your speedo, instrument cluster needs to come out to replace it.

Jun 16, 2009 | 1998 Buick Century

Not finding what you are looking for?
2000 Chrysler Concorde Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...